Kenmore / Sears Microwave Parts

Color: White. Size: 13 oz. Spray paint primer. can.

This thermostat controls oven/dryer temperature by opening or closing its contacts as the appliance reaches set temperatures, helping maintain safe and consistent operation. Replaces a worn or failed thermostat to restore proper temperature regulation. What it does:

• Senses temperature and interrupts heating when limits are reached to prevent overheating
• Re-establishes heating when temperature falls, maintaining normal cycle performance
• Commonly installed when an appliance won't heat, overheats, or cycles erratically
• Works as a direct replacement for the OEM thermostat designed for compatible LG units

• One thermostat

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Note wire locations or take a photo before removing wiring; reconnect wires to the same terminals
• Use a multimeter to verify thermostat continuity and correct operation before and after replacement

Secures microwave components to their mounting points. Replace this nut assembly if damaged, missing, or worn to prevent rattling and keep parts aligned.

This temperature thermistor is the sensor that lets the control board monitor and regulate appliance temperature for reliable cooling performance. Replacing a failing thermistor can restore proper temperature control and cycling. What it does:

• Senses internal temperature and sends readings to the control board
• Helps the compressor, fans, and defrost system run at the right times
• Commonly linked to symptoms like incorrect temperatures, overcooling, or frequent on/off cycling
• A faulty thermistor can cause improper defrost timing or erratic cooling behavior

• Disconnect power before inspecting or replacing the sensor to avoid shock
• Handle the sensor and wiring connector gently to avoid damage
• Mount the sensor in the original location and secure wiring per OEM routing

Microwave not heating? This magnetron generates microwaves to heat food. Replacing a faulty magnetron restores heating and stops cooking failures.

This is a plastic fan blade that attaches to the ventilation motor inside the microwave. It circulates air to cool internal components and, in over-the-range models, helps vent steam and cooking odors. Replace this blade if it is cracked, broken, or wobbling, which can cause excessive noise or reduced ventilation performance.

Microwave won't power up or shuts off after seconds? Failed thermostats cause intermittent operation. Test for continuity—straightforward repair.

Glass cover that sits over your microwave's cooktop surface. Replaces cracked, chipped, or broken covers to restore a smooth, protective finish.

Reduces electrical interference in your microwave. Mounts near the power supply. Replace if cracked, damaged, or causing blown fuses or failed operation.

Replaces a damaged or oxidized noise filter assembly in your microwave. Includes fuse holders and mounting hardware. Order a new one if terminals are discolored.

Fix microwave overheating or won't heat issues with this thermostat temperature limiter. Regulates oven temperature and prevents overheating damage.

This fan motor assembly cools the magnetron inside the microwave by circulating air to prevent overheating during operation. It includes the motor and fan blade as a complete unit. Replace this assembly if the microwave shuts off unexpectedly due to overheating, makes unusual noises during use, or the fan is no longer spinning.

This is a truss-head tapping screw used to secure trim, panels, and small assemblies on compatible LG appliances. It provides a low-profile, wide-bearing head that helps hold parts flush and resist pull-through. What it does:

• Fastens plastic and sheet-metal components where a self-tapping thread is needed
• Truss head spreads load to prevent damage to soft or thin materials
• Helps secure control panels, brackets, or trim pieces that require a low-profile head
• Common replacement when original mounting screws are missing, stripped, or corroded

• One truss-head tapping screw

• Use the correct screwdriver bit and moderate torque to avoid stripping the screw or workpiece
• Start threading straight and let the screw form threads without forcing at an angle
• Disconnect power and follow appliance-specific service safety procedures before working internally
• Replace any damaged mating threads or clips for a secure fit

Replacement screw that secures panels, trim pieces, and mounting brackets on cooktops and ranges. Needed when screws are missing, stripped, or damaged.

Factory mounting screw secures panels, brackets, and internal components in microwaves. Replace missing, stripped, or corroded screws to keep assemblies tight.

Microwave not heating or takes too long to warm food? This magnetron generates the microwaves that cook your food. Moderate repair difficulty.