Kenmore / Sears Microwave Parts

• Won't start

I had a blown fuse in which I replaced it and is up and running now. Read more

I searched the web and it seemed that many people had a similar problem when gunk got on the waveguide plate/cover. When I removed the cover, one of the plastic latches broke so rather than just trying to clean the plate, I had to order a new one. The new one arrived in just a couple of days, I put the plate on and at least for the last few days, no more arcing. <$10 fix for my over the stove microwave. Read more

Disassembled and replaced ac motor. The hardest part was to pull the microwave out of the cabinet. Read more

• Tray won't turn

Found Services online , was able to locate Part,by name and model. Place order and Received part total time 3 days. Well, pleased With handling, thought shipping was a bit High no more than weight, might ship in bubble Envelope. But still was please and will use your Servises Again 5??s. Donny Humphreys, South Carolina. Read more

Removed old broken door handle per video link on AppliancePartsPro.com. Installed new handle with no issues. <10 minute job at best. Read more

Main Fuse did not open, only fuse for high voltage section was opened. Prior to the fuse blowing a louder than normal hum was heard from microwave for 1-2 seconds prior. Easy fix is the high voltage capacitor, so first checked the voltage across the capacitor terminals to ensure capacitor was discharged. Typically should be reasonably discharged within 30sec-1min assuming drain resistor is still in place. Removed the high voltage cap, and checked the capacitance and did not get a reading.... Read more

Yes Read more

My daughter that she turned timer on but hit cook with nothing in the microwave. I was able to figure it was one of the four thermal cutoffs. It was obvious which one literally fried. Replaced that one worked like it was new. Took a lot of photos while dismantling and labeled the screws. Wasn't that hard just be careful of the capacitor Read more

I replaced the control board behind the keypad. Read more

Replace Thermostat on top of cavity. The thermostat is attached via 2 bending sheet metal tabs. Ours blew because the two wires connected to thermostat shorted, connectors melted. The short was caused by buildup of grease under thermal wire cover, shorting both leads. The unit is used heavily. This is the first thermostat to go. I had to replace wire connectors that connected to thermostat as well since the connectors were melted as well. Helpful hint. The grease build up was probably caused by... Read more

I replaced the two door switch interlocks and cam-plates which appeared to be worn. Before ordering the parts, I did a continuity check on the three door switches and determined that they were OK. While I was replacing the interlocks and cam-plates, I discovered that a piece on one of the cam-plates had broken off and was not making proper contact with the door switch when the door was closed. Read more

• shuts off after a few seconds

Ordered replacement transformer from appliance part pros.Found a video on youtube showing start to finish of how to remove and replace over the range microwave transformer. Received part amazingly fast, took about 45 minutes from start to finish to install new part. Microwave is like new, loud buzzing noise is gone! Thanks guys and a merry Christmas to all! Read more

I ordered a replacement handle from Appliance Parts Pro.com and installed it after watching the video at their site for a similar model. The video told of the trick on removing the door surround that allowed me to access the handle screws. I purchased new handle screws at the same time I bought the new handle. The new handle and screws were a bit different than the original but fit perfectly. Hopefully it will be more durable than the original handle. Read more

I bought the Housing-lmp, but when I got it at first I didn't think it was the right part because it didn't have the ceramic piece that it goes into. I didn't know that the ceramic piece slid over the housing. After one day of thinking about it I finally realized what I was looking at and put the new piece into the old ceramic piece. Read more