Kenmore / Sears Range Oven Control Or Thermostat

This Thermostat L225 is a temperature limit thermostat that helps regulate heat and prevent overheating in the appliance. It restores proper temperature control so the unit runs safely and more reliably. What it does:

• Acts as a temperature-regulating limit switch to stop heating when limits are reached
• Prevents overheating by opening the circuit at excessive temperatures
• Common symptom: appliance heating inconsistently or cutting out during cycles
• Can be checked for continuity when diagnosing heating problems

• Always disconnect power to the appliance before starting any repair
• Handle and install the part in the same orientation and mounting as the original
• Verify electrical connections are secure and use a multimeter to test continuity
• If other safety devices (thermal fuses/thermistors) failed, inspect and replace as needed per OEM guidance

A hi-limit safety switch that stops heating when temperatures get too high, protecting the appliance from overheating and helping prevent damage. Designed to replace a failed thermal cutoff to restore safe temperature control. What it does:

• Opens the heating circuit when internal temperature exceeds the safe limit to prevent overheating
• Commonly replaces a failed or intermittently opening thermal limit control
• Helps stop burners or heating elements from running unchecked when a thermostat fails
• Addresses symptoms like no heat, intermittent heating, or safety trip shutdowns

• Disconnect power before accessing heating components and wiring
• Verify the part matches the appliance diagram and wiring orientation before installation
• If corrosion or other damage is present on connectors or terminals, replace or repair per OEM guidance

This modulating thermostat controls oven temperature by cycling the heating element to maintain consistent cooking heat. It replaces a failed temperature regulator so your oven can reach and hold set temperatures more reliably. What it does:

• Senses oven temperature and modulates power to the heating element to stabilize cooking temperature
• Helps prevent large temperature swings that cause uneven baking or roasting
• Commonly replaced when the oven won't reach or maintain set temperature or cycles on/off too frequently
• Works as the temperature control interface between the oven sensor and the heating elements

• One modulating thermostat assembly

• Disconnect power to the appliance before beginning any repair to avoid shock or injury
• Handle thermostat and any attached sensing bulb or probe carefully; avoid kinking or damaging sensing components
• Verify wiring location and routing before removal; transfer all connectors exactly as removed

A safety thermostat that monitors and limits temperature at the range/stove backguard to help prevent overheating. Replaces a failed safety limiter to restore proper temperature control and safety operation. What it does:

• Acts as a temperature-limiting safety device for the range backguard assembly.
• Opens the circuit when temperatures exceed safe limits to prevent overheating.
• Commonly replaced when the oven or control fails to maintain temperature or shuts off unexpectedly.
• Helps address overheating, intermittent heating, or safety-trip symptoms tied to the backguard area.

• Disconnect power to the appliance before starting any repair to avoid shock or injury.
• Access may require removing the backguard panel and control housing; keep track of fasteners and wire routing.
• Verify electrical connections are secure and intact; replace only with correct part number.

This oven thermostat regulates cavity temperature to the set point on your range. Replacing a worn thermostat restores accurate heating and proper cycling, helping resolve undercooked or overbaked results, long preheat times, and temperature drift.

• Senses oven temperature via a capillary bulb and opens/closes internal contacts to maintain the selected setting
• Fixes ovens not reaching set temperature or running too hot/too cold
• Addresses ovens that won't cycle off or heat continuously
• Helps improve erratic temperature swings, inconsistent baking results, and extended preheats

• Disconnect power and allow the appliance to cool completely; turn off gas supply if applicable
• Note the exact routing of the sensing bulb/capillary; do not kink or sharply bend it, and reinstall bulb clips in the original location
• Transfer mounting hardware and the control knob as needed; align the shaft to match the original orientation
• After installation, verify operation with an oven thermometer; for gas models, leak-check any disturbed connections with an approved solution

This oven thermostat senses and regulates oven temperature so food cooks evenly and the range reaches set temperatures. It replaces a failed temperature control to restore accurate heating and cycle behavior. What it does:

• Closes and opens the control circuit to maintain the oven at the selected temperature
• Can correct symptoms such as oven not reaching set temperature, overheating, or excessive cycling
• Works with the oven's control system and heating elements to stabilize bake and broil operations
• Mechanical design — avoid bending or damaging the sensing element/capillary

• One oven thermostat

• Disconnect power to the appliance before starting any service
• Handle the thermostat and sensing element carefully; do not kink or sharply bend the capillary
• Verify proper thermostat mounting and oven cavity seals for accurate temperature control

This mechanical temperature control thermostat replaces a failed refrigerator control that cycles the compressor to maintain proper internal temperature. Restores reliable on/off switching so the appliance can hold set temperatures. What it does:

• Senses cabinet temperature and opens/closes the compressor circuit to regulate cooling
• Stops extended compressor run or prevents compressor from starting when thermostat fails
• Addresses symptoms such as warm refrigerator, inconsistent temperatures, or excessive cycling
• Works with mechanical control systems that use a physical sensing element

• Disconnect power to the appliance before starting any work
• Access may require removing the control housing or inner cabinet trim; keep track of fasteners
• Handle the sensing element gently; avoid kinks or sharp bends in the capillary/sensing tube