Kenmore / Sears Wall Oven Control Board

The Main Control Board is an OEM part for Frigidaire ranges. As the central processing unit, it coordinates bake/broil elements, lights, timers and sensory systems. Located inside the control panel area, this board continuously monitors range functions and relays information to the control display.

Causes can be splash or spill damage, power fluctuations over time, or inherent component failures due to age and usage. With proper replacement, full range functionality is restored.

Symptoms of a bad control board include:

• Knobs or buttons not working on the control panel
• Elements failing to heat properly
• Erratic temperature display readings
• Inability to preheat or maintain set oven temperatures
• Control locks that prevent range operation

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This electronic oven control board manages the bake/broil circuits and the clock/timer display. Replacing a failed board restores accurate temperature control and responsive keypad/display operation so your range can heat and time reliably again. What it does:

• Regulates power to the bake and broil elements based on temperature sensor feedback
• Interprets keypad inputs and drives the digital clock/timer display and alerts
• Controls oven relays for preheat, maintain-temp, and timed-cook functions
• Common failure symptoms include: no heat or intermittent heating, blank or unresponsive display, beeping/error indications, or oven that won't shut off

• 1 electronic control board

• Disconnect power at the breaker before servicing; verify no voltage is present
• Handle the board by the edges and use ESD protection to avoid static damage
• Note/photograph wire locations; transfer any mounting hardware or overlay from the original as applicable
• After installation, restore power, set the clock, and test all oven modes

This OEM replacement part is an oven control board. The oven control board is the primary computer circuit board that controls the main functions of the oven. These functions include turning the oven on as well as adjusting and maintaining the temperature of the oven. Luckily, replacing a control board is a simple process.To replace the board, first, make sure the oven is unplugged. Gain access to the back of the oven and remove the upper back panel. Once the panel is removed, locate the old control board. Take note of the orientation of the wires by taking a photo with a phone camera. Disconnect the wire harness and any individual wires that are attached to the old board. Re-secure the wires into their correct positions. Snap the new board back in place and reinstall the upper back panel.This genuine replacement control board is compatible with Frigidaire Electrolux, Gibson, Kelvinator, and Westinghouse brand ovens.

This electronic control board manages the oven's heating functions and the clock/timer display. Replacing a failed controller restores accurate temperature control, reliable cooking modes, and a working display on your range or wall oven. What it does:

• Controls heating element relays based on user input and temperature sensor feedback
• Operates the digital display, clock, and kitchen timer
• Coordinates oven modes such as preheat, timed bake, and self-clean
• Common symptoms of a failing board: no heat or erratic temperatures, blank/unresponsive display, beeping or error codes, inability to start or cancel bake/broil

• 1 electronic control board (controller) assembly

• Disconnect power at the breaker before servicing; this board carries live voltage
• Access through the control panel; remove panels/screws as needed to reach the board
• Move wire connectors one at a time from the old board to the new; take photos for reference
• Use ESD protection and avoid touching circuitry; set the clock and test all oven functions after installation

This electronic oven control board (clock/timer) is the brain of your range/oven, regulating temperature, powering the bake/broil circuits, and managing the display and keypad. Replacing it restores proper heating and responsive controls.

• Governs bake and broil circuits and maintains set temperature using oven sensor feedback
• Displays time/temperature and responds to keypad inputs
• Common failure signs: oven won't heat or start, erratic/inaccurate temps, dead or unresponsive display, repeated beeps or error codes

• Disconnect power at the breaker or unplug the appliance before servicing
• Handle the board by the edges and use anti-static precautions
• Photograph/label connectors and transfer wires one at a time to the new board
• Transfer the existing keypad overlay and any brackets as needed, reinstall panel, restore power, and test bake/broil

This electronic oven control board manages the oven's heating, keypad inputs, and display. Replacing a failed controller can restore responsive controls, accurate temperature regulation, and normal oven operation.

• Controls bake and broil heating through the oven's relays
• Interprets keypad inputs to start/stop modes, timers, and settings
• Drives the display for time, temperature, and status; may post fault codes
• Coordinates preheat, timed cook, and self-clean on applicable models
• Failure symptoms may include a blank or erratic display, unresponsive buttons, oven not heating or starting, inaccurate temperature, or beeping/error codes

• Disconnect power at the breaker or unplug the appliance before servicing
• Access the board behind the control panel/backguard on most models
• Move wire connectors one at a time from the old board to the new; take photos for reference
• Handle the board carefully and avoid static discharge to protect sensitive components

This Frigidaire oven range control board and clock are sold separately from the unit. The touchpad cover is also available individually. This control board contains the clock and timer digital display screen. This component is responsible for controlling the heat settings of the baking area and the electric cooktop. When a faulty control board continues active use in an oven, burners may begin to malfunction over weeks or months. Individual burners may work one day, and other days they may fail to power on altogether. This is also true of the baking and broiling functions of the oven. After the board fails, the clock and timer screen will fail to engage. The stove may also power on but fail to power off once the timer has reached its final countdown. On the back panel of the oven, there are rear screws that hold the control assembly in place. Remove these screws and turn to the inside of the stove. There are two anchor screws directly below the control assembly that fasten it to the cooktop. After removing these final screws, pull the control assembly off. Two tiny screws are holding the protective covering of the faulty control board. Remove these screws and disconnect the old control board/clock from the wiring harness. Proceed with the installation of the new component.This part is compatible with Frigidaire and Kenmore appliances. This is a genuine OEM part and is sourced directly from the manufacturer.

This is a relay control board manufactured by Frigidaire to replace a broken or faulty part in wall ovens.In order for the appliance to work as intended, the relay control board needs to be able to receive signals from the main control board. It can then send relays that regulate the oven's various elements. Should this part be worn, faulty, or malfunctioning, the appliance won't work as intended, if at all, thus requiring replacement. To prevent injury, always wear work gloves and disconnect all power sources entirely from the appliance.This OEM relay control board is sold individually and manufactured from durable materials. It is compatible with wall ovens manufactured by various brands, including Frigidaire, Electrolux, Kelvinator, and Westinghouse.

The Oven Control Board is an OEM part for Frigidaire ranges. It is the central processor that regulates all heating functions, cooking modes, timers and safety features through electronic controls.

Causes of a bad control board can include moisture infiltration over time, loose connections, or component failures due to power fluctuations or surges.

Symptoms of a bad oven control board include:

• Elements not heating or cutting off as programmed
• Inaccurate temperature readings or inconsistent regulation
• Bake and broil modes not functioning properly
• Constant error codes or safety lockouts displayed

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This clock timer is the electronic oven control that governs timekeeping and oven functions. It displays the clock and settings and directs power to the bake/broil circuits so the oven responds to your commands.

• Controls and displays the clock, kitchen timer, and oven settings
• Sends power to bake and broil relays based on selected temperature and mode
• Coordinates preheat and cycle timing for consistent results
• Common signs it may be needed: blank or dim display, unresponsive buttons, error codes/beeping, oven won't start or heat though elements and power test good

• Disconnect power at the breaker before servicing—this is a high-voltage electronic part
• Access through the control panel or backguard; remove panel screws to reach the control
• Move wire connectors one at a time to the new control; reuse any mounting hardware
• Handle the board carefully to avoid static discharge; after installing, restore power and set the clock, then test oven functions

The Noise Filter is an OEM part for Whirlpool built-in wall ovens. It is installed inside the oven cavity near components that produce vibrations, such as the convection fan motor. 

Causes of a faulty noise filter include the degradation of noise-dampening materials over many heating and cooling cycles. Physical damage from accidental impact during cleaning could also compromise its sound-blocking ability.

Symptoms of a bad noise filter include: 

• Excessive buzzing or humming noises emitted from the oven cavity
• Louder than normal fan or component sounds carrying into the kitchen
• Vibrations felt externally on the oven chassis during operation

This OEM replacement fits several Whirlpool, KitchenAid, and Jenn-Air wall oven models.

This electronic oven control board governs your range's heating functions and displays the time and timer. Replacing a failed board restores reliable bake/broil operation, accurate temperature control, and a responsive clock/timer interface. What it does:

• Controls bake/broil circuits to run selected cooking modes
• Monitors the oven temperature sensor and regulates heat to the set temperature
• Drives the time-of-day and countdown timer display
• Interprets keypad inputs for mode selection and settings
• Failure symptoms can include no heat or erratic heat, a blank or flickering display, or unresponsive buttons

• One electronic control board assembly

• Disconnect power at the breaker before servicing; verify no voltage is present
• Use anti-static precautions and handle the board by its edges
• Photograph wiring and transfer connectors one at a time to the same positions
• Reuse the existing mounting hardware and any faceplate/overlay as required; set the clock after restoring power

This genuine OEM replacement part is a clock timer for ovens. If the display is dim, not visible, and the buttons aren't functioning properly, this could be a sign that the clock timer needs to be replaced. Luckily this is a relatively simple repair. Unplug the oven. The first step is to remove the top panel to gain access to the timer module. Once the top panel is removed, pull the brackets that hold the clock and timer in place. Make sure to take note of the orientation of the wires by taking a picture with a phone camera. Remove the wires and reconnect them to the new clock timer. Snap the timer module back into its original place. Reinstall the top panel and push the oven back in place.This replacement part is sold individually and is compatible with Frigidaire, Electrolux, Gibson, Kelvinator, and Westinghouse ovens.

The Control Board is an OEM part for Frigidaire ovens. It is an integral electronic component responsible for operating various functions of the oven such as temperature controls, timers, displays, and sensors. The control board works behind the scenes to ensure reliable and consistent cooking performance. 

Causes of a bad control board can include exposure to excess heat over time, damage from electrical surges, or failures in electronic components. 

Symptoms of a bad control board include:

• Lights or displays not working properly 
• Inability to control temperature or time settings
• Unexpected shutdowns or failure to operate as directed
• Error codes appearing on the display

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. Installation is recommended by an experienced technician.

This is a replacement oven range control board and clock from Frigidaire. It is the heart of the oven and is responsible for managing and monitoring all functions. It allows the user to set the oven temperature, choose baking/broiling cycles, set timers, and more. This part should last for many years, but it can be damaged by prolonged exposure to moisture or high heat.If the control board is failing or has failed, the oven may be inoperable, or it may experience erratic or erroneous operation. A multimeter test is needed to determine if the problem is the control board, though. This part does not include the overlay, which is needed to capture user inputs. To replace the control board and clock, users will need to unplug the oven. Remove the rear access panel of the oven, locate the wiring harnesses, then disconnect them. Remove the mounting screws and then the old board. Install the new board by reversing these steps. This control board is a genuine OEM part and is sold individually. It is compatible with Kenmore ovens.

This electronic control board manages the appliance's user interface and core operating functions so the unit responds to control input and runs set cycles correctly. Replacing a faulty board restores reliable control and display operation. What it does:

• Interprets user commands from the touchpad/controls and sends signals to motors, valves, heaters, and other components
• Manages cycle timing, settings, and display feedback for normal operation
• Common symptom: control or display is unresponsive, shows error codes, or buttons do not register
• Common symptom: appliance fails to start, stops mid-cycle, or behaves erratically due to lost control signals

• One electronic control board (controller)

• Disconnect power before accessing or replacing the control board to avoid shock risk
• Handle the board by its edges and avoid touching circuit traces or components
• Verify connectors are fully seated and routed clear of moving parts before reapplying power