Skip to Content
  • time delivery images 2 Day Quick Delivery!
  • box-refresh images 365 Day Return Policy!
  • lovely images 15 million satisfied customers
  • boxes images Over 2.1 Million Parts In Stock
  • headphone imagesFree Tech Support!
  • google images Google Trusted Store

Kenmore / Sears Washer Dryer Combo Power Nut Or Trunnion

Kenmore Support (Trunnion), Single
Genuine Frigidaire part
By: Frigidaire
Part Number: 5304466677

This trunnion support fits the appliance's rotating assembly to stabilize and guide the drum or door hinge, restoring proper alignment and smooth operation. Durable replacement designed to match the original mounting points. What it does

  • Supports and locates the drum or hinged assembly to prevent wobble and misalignment
  • Reduces rubbing, scraping, or grinding noises caused by a worn support
  • Helps keep the door/drum tracking true so the appliance opens/closes and spins correctly
  • Common symptom: visible sagging, uneven rotation, or unusual noise during operation
What's included
  • One (1) support (trunnion) as shown
Install notes
  • Disconnect power (and gas if applicable) before servicing; follow all safety precautions
  • Remove panels or drum/door per service manual to access the trunnion; retain mounting hardware if reuse is intended
  • Inspect adjacent bearings, seals, and mounting tabs for wear and replace as needed
  • Test appliance on a short cycle after installation to ensure proper alignment and quiet operation

Do-It-Yourself Stories from Customers like You Noisy during the washer spin cycle and leaking water   John P. • Wasilla , AK • April 16, 2022

The noise turned out to be the bottom bearing between the belt pulley and the transmission. Once apart an easy replacement. But you did need some tools to replace the bearing as in snap ring pliers and bearing puller. The water leak was the top rubber seal which is part of the seal kit. I had to make a puller out of some chain and a 2 jaw-bearing puller to the top of the transmission shaft to get the trunnion off but once it was off the rest was a snap. The video was a big help. Tested the... Read more

More
$163.32
Compare At:
$192.72
You Save:
$29.40

Out Of Stock

Usually ships within 4 - 14 days

Add to Cart
Kenmore Trunnion (Washer Inner Tub Hub)
Genuine Frigidaire part
By: Frigidaire
Part Number: 131545101

The trunnion is the hub that mounts the washer's inner tub to the drive shaft. Replacing a worn hub restores a solid, centered connection so the basket spins smoothly without wobble, slip, or grinding. What it does:

  • Secures and centers the spin basket on the drive shaft for balanced rotation
  • Transfers drive torque to the inner tub during spin
  • Helps maintain basket alignment to reduce vibration
  • Typical symptoms of failure: loose/wobbly tub, scraping or grinding noises, poor or no spin, frequent out-of-balance events
What's included:
  • 1 trunnion
Install notes:
  • Disconnect power and water before service; wear gloves and eye protection
  • Access the hub by removing top/access parts, then the agitator/wash plate and inner-tub fasteners
  • Clean the shaft and mating surfaces; seat the new trunnion fully and tighten fasteners evenly in a crisscross pattern
  • Inspect related parts (tub seal, bolts, bearing) while open and replace if worn; run a short test cycle to ensure smooth spin

Do-It-Yourself Stories from Customers like You Leaking washer tub   Hugh S. • Miami , FL • June 25, 2016

The seal at the bottom of the tub had started to fail. On large loads water would leak so I ordered a new one rubber seal. Getting the trunnion off the transmission shaft was hard as it was calcified and corroded. I used a wire brush to get some of it off and then used a lot of WD-40. The bolt holding the trunnion plate on sheared off when I tried to remove it on one side and the other came out ok (the bolt hole through the trunnion is not threaded so it should slide out once the plate is off... Read more

More

Kenmore / Sears washer dryer combo power nuts or trunnions replacement parts are crucial in maintaining the optimal performance of your appliance. Keeping your washer dryer combo in top shape ensures that your laundry routine remains a breeze, and these specific parts play an integral role in making that possible.

Your Kenmore / Sears washer dryer combo is a true workhorse, simplifying laundry tasks by combining washing and drying functionalities. The power nut and trunnion parts help ensure that the mechanical motions within the appliance are smooth and effective. With quality replacement parts like OEM components, you're guaranteed a perfect fit and long-lasting durability, preserving the efficiency of your washer dryer combo.

Incorporating high-quality Kenmore / Sears washer dryer combo parts into your maintenance routine means you can trust in the longevity and reliability of your appliance. Whether you need a power nut to maintain the integrity of the machine's movement or a trunnion to support its mechanical framework, these parts are designed to keep your appliance running seamlessly. Rest assured, the availability and quality of these parts mean that your trusted Kenmore or Sears washer dryer combo will continue to serve your household effectively for years to come.

More
  • boxes images Over 2.1 Million Parts In Stock
  • time delivery images 2 Day Quick Delivery!
  • box-refresh images 365 Day Return Policy!
  • headphone imagesFree Tech Support!
  • google images Google Trusted Store