Kenmore / Sears Washer Dryer Combo Control Board

This dryer timer is the cycle control that advances your dryer through Timed and Auto Dry settings. Replacing a failed timer restores proper cycle progression, start/stop, and end-of-cycle shutoff.

• Advances the cam and internal contacts to move the dryer through heat, motor, and cool-down steps
• Governs run time on Timed Dry and Auto Dry cycles
• Routes power to the correct circuits in sequence; a failed timer may not advance or may stop early
• Common symptoms include timer knob not moving, dryer running indefinitely, or not starting on certain settings

• Disconnect power; for gas models, also shut off gas
• Remove knob/dial, open the console, and unmount the timer
• Label or photograph wiring; transfer wires one at a time to the new timer
• Reassemble and test both a Timed Dry and an Auto Dry cycle

The Dryer Timer is an OEM part for Frigidaire dryers. It is responsible for controlling the drying cycles by regulating the amount of time the dryer runs. The timer ensures that clothes are dried according to the selected settings, contributing to efficient and effective drying performance.

Causes of a bad timer can include electrical issues such as a short circuit, worn-out internal components due to frequent use, or exposure to moisture that can damage the timer mechanism.

Symptoms of a bad Dryer Timer include:

• The dryer not advancing through cycles
• The dryer running continuously without shutting off
• Inconsistent drying times
• The timer knob not turning or feeling loose

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This replacement timer is made by Frigidaire and is compatible with commercial washers.This timer controls the internal components that monitor the duration of the cycles. If the user notices that the laundry center cycles are not running for the correct amount of time or do not start at all, the timer may need to be tested for continuity and then replaced. Make sure to entirely disconnect the appliance from the power and water sources and wear work gloves before attempting any repairs or replacements. This is an authentic OEM part made of high-quality, durable, non-corrosive materials and is only sold individually. This timer can be used with washers that have been manufactured by Frigidaire, Kenmore, Electrolux, Gibson, Kelvinator, Westinghouse, and some other brands.

This dryer timer controls the sequence and length of drying cycles. Replacing a failed timer restores consistent cycle advancement and automatic shutoff so your dryer starts, runs, and ends at the correct time. What it does:

• Advances the selected cycle by opening and closing internal switch contacts on schedule
• Coordinates start/run timing and end-of-cycle shutoff for timed and auto settings
• Common failure signs: timer knob doesn't advance, dryer runs too long or won't shut off, stops early, or only certain cycles work

• Includes 1 dryer timer assembly

• Unplug the dryer or disconnect power before servicing
• Access the timer from the console; remove the control knob and mounting screws to release it
• Transfer wires one at a time to matching terminals on the new timer using your model's wiring diagram
• Mount securely, reassemble the console and knob, then test for proper cycle advancement

Made to be used on washing machines, this part is a timer. This component controls the electrical parts and the duration of time of the washing machine's cycles. It controls the operation of the washing machine, including each of the cycles.When the timer will not advance, the washing machine could become stuck in a cycle and run constantly without stopping. The washing machine may not advance through the particular cycle like the washing, rinsing, or spinning and could get stuck on one of the cycles. It's important to unplug the washing machine from the electrical outlet before attempting to repair or replace any parts. The replacement process is fairly easy and takes about 15 minutes to complete.This timer is compatible with washing machines that are manufactured by the Frigidaire, Gibson, Kenmore, and White-Westinghouse brands. This part is sold individually and is sourced straight from the manufacturer itself.

This mechanical cycle timer controls the sequence and duration of wash, rinse and spin functions in compatible top-load washing machines, restoring proper cycle advancement and timing. What it does:

• Advances the washer through timed cycles so selected wash, rinse and spin functions run in the correct order.
• Routes power to the washer's motor and valves at the right points in the cycle.
• Commonly replaces timers that cause machines to get stuck on one cycle, fail to advance, or not complete a cycle.
• Works with the machine's existing control knobs and wiring harness to restore automatic cycle sequencing.

• Disconnect power to the washer before beginning any service to avoid electrical shock.
• Service typically requires access behind the console or control panel; remove panels carefully and keep fasteners organized.
• Note and photograph wiring connections before removal; reconnect wires to the same terminals.

This replacement part is a timer manufactured by Frigidaire and intended to replace a faulty or broken timer in various models of washing machines. The timer controls the duration of the washing machine cycles via the electrical components of the appliance. If the user is struggling to control the washing machine cycle lengths, then this part may need to be replaced. The washing machine should be entirely disconnected from the power and water sources before any repair attempts are made. It's recommended that work gloves are worn to ensure the hands are protected. This is a genuine OEM part and has been sourced directly from the manufacturer. As an authentic replacement part, this timer is suitable for use with various models of washing machines that have been manufactured by Frigidaire, Electrolux, Gibson, and various other brands. This part is sold individually.

This is a Frigidaire washer/dryer combo timer. The washer or dryer timer controls all the timed functions of the appliances, including the cycles and draining. Without a working timer, there is no way for the machine to judge when to start certain parts of the cycle, when to drain water, start rinsing, switch from hot to normal air, and many other tasks. When a timer goes out on these machines, a replacement needs to be ordered immediately. To replace this part, first unplug the appliance from the main power source. This timer is a genuine OEM replacement part sourced directly from Frigidaire. This part is only available individually and is not included with other parts or the main appliance. This product is compatible with Frigidaire appliances.