Kitchenaid Cooktop Parts

The range conversion kit is an OEM component specifically designed for Whirlpool ranges. This kit contains all the necessary parts to convert a range from natural gas to propane gas or vice versa. 

Symptoms of an incompatible or incorrectly installed conversion kit include:

• Incomplete or unstable burning of the gas 
• Yellow burner flame tips instead of blue
• Higher than normal gas usage
• Issues with ignition or flammability 

Causes of a bad conversion kit could be improper installation, damaged or missing components, or using a kit not designed for the specific range model.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This is the black control knob that mounts on your range or cooktop's control shaft, letting you select heat levels and settings with a clear, factory look. Replacing a worn knob restores proper grip and accurate pointer alignment.

• Mounts on the control shaft to select burner or function settings
• Restores smooth turning and positive indexing
• Ideal replacement for cracked, stripped, loose, or missing knobs
• Helps ensure settings are clearly indicated and easy to adjust

• Disconnect power and, if applicable, shut off gas before servicing
• Pull the old knob straight off the shaft; avoid prying against the control panel
• Align the new knob with the shaft and press firmly until fully seated
• After installation, verify smooth operation and correct pointer alignment

This wire harness connects the control/switch assembly to the appliance's thermal cutoff and control circuits, restoring reliable electrical connections for proper operation. It's a direct-fit replacement when the original wiring is damaged or corroded. What it does:

• Provides the factory routing and connectors between the control/switch and TCB/thermal cutoff
• Re-establishes lost or intermittent power caused by damaged wiring or broken terminals
• Helps stop failures that cause controls to be unresponsive or cycles to stop unexpectedly
• Uses OEM-style terminals and insulation to match original fit and function

• One wire harness (switch TCB) as shown

• Disconnect power before starting — verify the appliance is completely de-energized
• Take photos of existing wire routing and connector locations to ensure correct reassembly
• Plug connectors fully and secure the harness along original clips or tie points; avoid sharp edges
• If terminals are damaged at mating parts, inspect and replace those components rather than splicing connectors

This single surface burner spark electrode generates the spark that lights the gas on your cooktop or range. Replacing a worn or cracked electrode restores reliable ignition and reduces "click with no flame" at that burner.

• Creates a high-voltage spark at the burner to ignite gas
• Positions the spark at the burner head via a ceramic-insulated tip
• Common symptoms: burner won't light, no spark at that burner, or intermittent ignition
• Visual clues of failure can include cracked/chipped porcelain or a burned electrode tip

• Disconnect electrical power and shut off gas supply before servicing
• Allow the appliance to cool; remove burner cap/head to access the electrode
• Seat the ceramic insulator fully and position the tip correctly near the burner
• Reassemble and test ignition before finalizing the repair

This burner inner cap is the small metal cap that sits on the center of a gas cooktop burner head to help direct and shape the flame for even heating. Replacing a damaged or misplaced cap restores correct burner performance and consistent cooking heat. What it does:

• Covers the burner head and helps direct gas flow for a stable, even flame
• Helps maintain proper flame pattern to avoid hot spots and uneven cooking
• Can resolve weak, flickering, or irregular flames when the cap is warped or missing
• Protects the burner head from spills and debris that can block ports

• Turn off the range and allow the burner to cool completely before servicing
• Remove the burner grate and lift off the old cap; seat the new cap flat onto the burner head
• Do not force or pry the cap into place—align it and let it sit naturally on the burner surface
• After installation, check burner ignition and flame pattern; if you smell gas or see unsafe flames, stop use.

This igniter top is the spark electrode that produces the spark to light a gas cooktop burner, restoring reliable ignition for safe cooking. It replaces the worn or damaged electrode that fails to spark or lights intermittently. What it does:

• Sends the spark to ignite the burner when the control is turned on.
• Commonly used when burners click but do not light or flame is slow to ignite.
• Helps stop continuous sparking caused by cracked or misaligned electrodes.
• Works with the burner cap and gas valve to ensure consistent ignition.

• One igniter top (spark electrode) as shown

• Disconnect power and shut off gas supply before attempting replacement.
• Handle the ceramic insulation carefully to avoid cracking; inspect wiring and connectors for damage.
• Verify correct part number and fit with your appliance diagram before ordering.

Adjustable leveling feet that restore stability and balance to your appliance by letting you fine-tune height at each corner for a flat, wobble-free install—helps reduce vibration and improve door fit and operation. What it does:

• Provides adjustable height to level an appliance on uneven floors.
• Eliminates rocking or wobbling that can cause vibration, noise or movement during operation.
• Helps ensure doors and panels sit flush and seal properly.
• Durable replacement designed for direct fit where the OEM leveling foot is specified.

• Disconnect power and water before performing any work.
• Support the appliance so it cannot tip—use a jack or have a helper hold it while you adjust feet.
• Turn the foot to raise or lower the corner; use hand tools as needed and avoid excessive force.
• After adjusting, check stability and run a short cycle to ensure vibration and alignment are resolved.

Replacement cooktop top panel that restores the range's cooking surface and provides a sturdy mounting surface for burners and controls. Ideal when the original top is dented, rusted, cracked, or cosmetically worn. What it does:

• Replaces a damaged or corroded cooktop top to restore appearance and structural support
• Provides the proper mounting surface and alignment for burners, grates, and control components
• Helps eliminate gaps or uneven seating caused by a warped or dented top
• Preserves factory attachment points and finish for a correct fit

• Disconnect power and shut off gas supply before starting any repair
• Remove burner grates, burners, and control assemblies as required to access mounting screws
• Use appropriate hand tools and keep track of screws and brackets; some fasteners may be reused
• Wear gloves and take care handling edges; refer for model-specific instructions

This heat deflector directs and shields heat inside the appliance to help protect surrounding components and maintain proper airflow. It's a simple replacement for torn, warped, or missing deflectors. What it does

• Redirects heat away from sensitive components to reduce risk of heat damage
• Helps maintain consistent airflow paths for proper appliance performance
• Commonly replaced if warped, cracked, melted, or dislodged
• May reduce odors or burning smells caused by contact with hot parts

• Disconnect power (and gas, if applicable) before beginning any repair
• Inspect surrounding mounting points and replace any damaged fasteners if needed
• Handle carefully—sharp edges may be present

The Valve-Gas is an OEM part for Whirlpool gas cooktops. This valve is located underneath the cooktop and is responsible for controlling the flow of gas to each burner. 

Symptoms of a bad gas valve can include:

• Inability to ignite or adjust certain burner flames
• Gas leaks or smells around the valve area 
• Intermittent or irregular flame levels
• Yellow flames that pose a safety risk

Over time and with heavy usage, components inside the valve can wear down affecting proper gas regulation. 

Compatible models also include KitchenAid, Jenn-Air, Magic Chef, Admiral, and some Kenmore units. 

Replacement bezel that fits around a control knob to restore a clean appearance and secure knob fit. Helps reduce knob wobble and protects the control shaft from dirt and spills for reliable knob operation. What it does:

• Covers the control shaft and provides a finished look to the knob area.
• Restores a snug, centered fit when the original bezel is cracked, worn, or missing.
• Reduces knob wobble and play that can affect control feel.
• Helps keep debris and liquids away from the control shaft to prevent interference.

• Disconnect power (unplug appliance or shut off circuit) before removing or replacing knobs.
• Remove the control knob, then pry or unclip the old bezel from the panel; install new bezel by aligning and snapping into place.
• Inspect for broken clips or mounting points; replace any damaged fasteners to ensure a secure fit.

This grate kit replaces damaged or missing cooktop grates to restore a stable cooking surface and proper cookware support. Designed to fit and align with the range burners for safer, more even heating. What it does

• Replaces cracked, chipped, warped, or missing grates that prevent cookware from sitting level
• Restores proper burner alignment and stability for pots and pans
• Helps reduce burner interference caused by damaged grate surfaces
• Matches OEM fit and mounting points for straightforward replacement

• Grate kit as shown

• Turn off the appliance and ensure the cooktop and burners are completely cool before starting
• Remove existing grates and clean the cooktop before fitting the new parts
• Set grates into place by aligning with burner supports; no special tools typically required

This surface igniter is the replacement spark electrode used on gas cooktop burners to create the spark that lights the burner. It restores reliable ignition so burners light when you turn the control knob. What it does:

• Produces the spark that ignites the gas at a surface/burner element
• Replaces a cracked, worn, or non-sparking electrode
• Common fix for burners that click but won't light or that fail to spark
• Works with the existing electrode wiring and mounting location

• Disconnect power to the range and turn off the gas supply before starting
• Handle the ceramic tip gently to avoid chipping; do not touch the tip with bare hands
• Confirm correct orientation and secure mounting; match wiring to original connections

The Burner Head is an OEM replacement part for Whirlpool gas ranges. This is the smaller burner head and it distributes gas evenly through the ports to produce a focused and consistent flame for temperature control during cooking.

Size: Small

Due to spills, grease buildup, corrosion, or wear and tear, the small burner head can deteriorate, clogging its ports and affecting gas distribution. When this occurs, the burner head may struggle to maintain a steady flame, impacting cooking performance.

Symptoms of a faulty Small Burner Head include:

• Uneven or low flames on the small burner
• Difficulty igniting the burner
• Clogged ports or visible rust/corrosion

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

A hi-limit safety switch that stops heating when temperatures get too high, protecting the appliance from overheating and helping prevent damage. Designed to replace a failed thermal cutoff to restore safe temperature control. What it does:

• Opens the heating circuit when internal temperature exceeds the safe limit to prevent overheating
• Commonly replaces a failed or intermittently opening thermal limit control
• Helps stop burners or heating elements from running unchecked when a thermostat fails
• Addresses symptoms like no heat, intermittent heating, or safety trip shutdowns

• Disconnect power before accessing heating components and wiring
• Verify the part matches the appliance diagram and wiring orientation before installation
• If corrosion or other damage is present on connectors or terminals, replace or repair per OEM guidance

This surface heating element replaces a faulty top burner to restore direct cooktop heat. It mounts into the range top and connects to the stove wiring for reliable heating when operating correctly. What it does:

• Heats cookware directly as the cooktop's top burner element
• Replaces a cracked, warped, or non-heating burner element
• Fixes intermittent heating, no-heat, or uneven heating on the affected burner
• Restores normal surface temperature control when the switch and wiring are functioning

• Disconnect power at the breaker before servicing to avoid shock
• Handle the element carefully; avoid bending terminals or damaging insulation
• Verify terminal connections are tight and the range wiring is in good condition