Kitchenaid Range Parts

This replacement control knob restores a worn, cracked or missing stove/dryer control interface so you can easily select heat and cycle settings. Durable plastic construction and simple push-on fit make it a quick fix. What it does:

• Replaces a damaged or missing control knob so the appliance dial turns smoothly
• Provides a clear grip for selecting temperature, cycle or timer settings
• Stops slipping, cracking or broken pointer issues that prevent proper selection
• Fits the original control shaft to restore normal user control

• One control knob

• Disconnect power to the appliance before servicing electrical or heating controls
• Pull the old knob straight off the control shaft; press the new knob firmly into place
• If the knob resists or the shaft is damaged, inspect the control shaft and replace any worn components
• No calibration required after installation; test operation at low power first

This small mounting clip secures small panels and components on compatible Whirlpool appliances, restoring proper fit and preventing parts from coming loose. It's a simple replacement that helps stop rattles and misaligned panels. What it does:

• Secures trim, panels or small components to the appliance frame to maintain proper alignment
• Prevents parts from shifting or vibrating during operation, reducing rattling noises
• Restores fit where a broken or missing clip allowed gaps or loose pieces
• Designed to snap into place for a secure hold without added hardware

• One clip

• Disconnect power to the appliance before attempting any repair
• Remove any trim or panels carefully to access the clip location; note original orientation
• Press or snap the clip into the mounting slot until it seats; some locations may require a flat tool or light force
• Replace or repair the adjacent parts for a secure fit

This switch seal is a small rubber gasket that protects a control or door switch from moisture and debris, helping maintain reliable operation and prevent damage to the switch assembly. What it does:

• Creates a moisture- and dust-resistant barrier around a switch to reduce shorting and corrosion
• Helps keep switches operating smoothly by blocking contaminants that cause sticking or intermittent contacts
• Supports safe electrical performance by keeping water away from switch terminals and housings
• Common symptom linkage: switch malfunction, intermittent control, or moisture-related failures near switch area

• Disconnect power to the appliance before inspecting or replacing the seal
• Remove surrounding trim or components carefully to avoid damaging the switch or housing
• Confirm correct orientation and full seating of the seal during reassembly for an effective barrier
• If the switch shows damage or corrosion, replace the switch assembly as well

This control knob replaces a worn, cracked, or missing push-on knob so you can turn and set appliance controls easily. It restores a secure grip and clear control feel for smooth operation. What it does:

• Fits onto the control shaft to allow manual selection of cycles, temperatures, or settings
• Restores a solid grip when the original knob is stripped, cracked, or loose
• Provides precise rotation and tactile feedback for accurate setting changes
• Helps prevent accidental setting changes by providing a secure fit

• Disconnect power to the appliance before servicing.
• This knob installs by pushing onto the splined control shaft; pull straight off to remove.
• Do not force; align splines before seating to avoid damage.
• If knob will not seat or the shaft is damaged, inspect/replace the control shaft or console components.

The Burner Cap is an OEM component specifically designed for Whirlpool gas ranges. Located atop each surface burner element, it creates an ideal heating footprint optimized for common cookware.

Symptoms of a faulty burner cap often include misshapen or distorted areas from prolonged exposure to high temperatures. Discoloration or scaling along outer rims occurs as well from mineral accumulation over many years.

Symptoms of a bad burner cap include:

• Caps appear badly twisted or misshaped
• Grime builds up in hard-to-clean sections
• Flame patterns become irregular or unstable
• They show signs of cracking

This OEM Whirlpool replacement burner cap restores safe, uniform heating. Installed promptly to remedy burners scorched underneath, it averts continued performance compromises from further damage or debris traps. 

Compatible also with some GE and Frigidaire range models, this part maintains efficient energy use for cooking convenience. 

This genuine replacement wire harness connects and routes power and signal lines between appliance components, restoring reliable electrical communication for normal operation and control response. What it does:

• Replaces damaged or frayed wiring that can interrupt power or signals
• Restores reliable connections between controls, motors, and sensors
• Helps resolve intermittent operation, loss of certain functions, or failure to start when caused by wiring faults
• Provides factory-style connectors and routing for secure, vibration-resistant connections

• Disconnect power to the appliance before starting any repairs
• Handle connectors carefully; match connector shapes and colors to the original
• Route the harness as the OEM diagram specifies and secure with clips or ties to prevent chafing

Color: Biscuit. Other colors: For black use WP9750372FF, for white use WP9750372FW.

This switch bracket mounting seal replaces a worn or damaged seal that cushions and protects the door or control switch mounting area. It helps keep the switch assembly seated and reduces debris and moisture intrusion for reliable operation. What it does:

• Seals the switch bracket mounting area to protect the switch from lint, dust and moisture
• Helps keep the switch properly positioned for accurate door or control sensing
• Can prevent intermittent or failed switch contacts caused by contamination or misalignment
• Useful when replacing a brittle, torn or missing mounting seal during switch or door repairs

• Disconnect power to the appliance before starting any repair
• Remove the door or panel per service instructions to access the switch bracket area
• Fit the seal into the bracket groove or around the switch housing, ensuring full seating without stretching
• Inspect adjacent clips or screws and reuse or replace as needed; test the switch function after reassembly

This ground wire provides a safe chassis connection to restore proper grounding and reduce shock and electrical-fault risk. It replaces a frayed, corroded or missing ground lead to help keep the appliance electrically safe. What it does

• Connects the appliance chassis to the grounding system to prevent stray voltage on metal surfaces
• Restores a secure ground path if the original wire is broken, loose, or corroded
• Helps stop intermittent power faults or nuisance tripping caused by a compromised ground
• Addresses symptoms like visible wire damage, loose ground connection points, or grounding-related electrical issues

• One ground wire

• Always disconnect power (unplug or shut off the circuit breaker) before starting work
• Attach the ring/terminal ends to the designated chassis ground screw and the equipment ground point
• Route the wire away from moving parts, heating elements, and sharp edges; secure with existing clips or fasteners
• If terminal hardware is missing or damaged, replace with equivalent OEM-style fasteners and torque to specification

This gas tubing supplies gas from the oven manifold to the burner assembly, restoring a safe, direct fuel path for proper ignition and heating. Use when tubing is cracked, corroded, kinked, or leaking. What it does:

• Carries gas from the appliance's manifold or valve to the burner(s)
• Maintains a sealed, flexible connection to allow component movement
• Replaces damaged, corroded, or pinched tubing that can cause leaks or poor ignition
• Helps restore consistent burner performance and proper heating when tubing is compromised

• Turn off gas supply and electrical power before starting any service
• Verify correct orientation and secure fittings to avoid leaks; use OEM-specified fittings and torque
• Leak-test all connections with a soap solution or approved leak detector before returning appliance to service

This replacement control knob restores a range or cooktop's user control, making it easy to set or change heat and function settings. Simple to install, it refreshes worn or broken knobs so you can operate controls safely and accurately. What it does

• Provides a firm, easy-to-grip control for adjusting temperature and function settings
• Replaces cracked, stripped, or missing knobs that slip or won't turn
• Restores clear pointer alignment so settings register correctly
• Helps prevent accidental changes by fitting securely on the control shaft

• Disconnect power to the appliance before servicing for safety
• Pull the old knob straight off the control shaft; some models may require loosening a set screw
• Align the new knob's splines or hub with the control shaft and press firmly until seated
• Test control operation after installation; stop if it resists or binds

This control knob replaces a worn, cracked or missing appliance knob to restore safe, easy control of oven or range settings. It provides a simple push-on replacement so you can turn controls smoothly and confidently. What it does:

• Replaces a damaged or missing control knob so you can set temperatures or functions accurately
• Restores secure grip and tactile feedback for safer operation
• Helps stop slipping or inconsistent control caused by stripped or broken knobs
• Fits the original control shaft design for a direct replacement

• Disconnect the appliance from power before servicing to avoid injury.
• Remove the old knob by pulling straight off the control shaft; align and push the new knob onto the shaft until seated.
• If the knob feels loose or won't fit, verify shaft style and part number before forcing.

This orifice spud directs gas flow into the burner for consistent ignition and flame control. It restores proper burner performance so cooking heats evenly and burners light reliably. What it does:

• Seats the burner orifice to control gas flow to the burner
• Helps maintain a steady, even flame for consistent cooking
• Can resolve weak or uneven flames and burners that struggle to light
• Works as the sealed interface between the gas manifold and burner tube

• One orifice spud

• Turn off the gas supply and disconnect power before servicing
• Inspect surrounding seals and gaskets for damage and replace if necessary
• Use basic hand tools; avoid overtightening to prevent damage

This burner cap kit replaces worn or damaged black burner caps on gas cooktops to restore proper flame shaping and even heat distribution for safer, more reliable cooking. Fits select gas range burner configurations. What it does:

• Covers the burner head to help direct and shape the flame for consistent heating
• Protects the burner base from spills, corrosion, and debris that can affect performance
• Helps reduce flare-ups and uneven cooking caused by damaged or missing caps
• Resolve visible flame irregularities, poor ignition, or partial burner shutdowns

• Turn off the cooktop and gas supply and allow components to cool before servicing
• Remove old caps, clean burner head and surrounding area, then seat new cap flat and centered
• No special tools typically required; check fit and ignition before full use

This orifice spud is the small gas jet used in LP conversion kits to regulate propane flow to a burner, helping restore correct flame size and combustion after converting to liquid propane. It's a direct-fit component for affected burners. What it does:

• Replaces the burner jet that meters propane for safe, consistent flame
• Restores proper flame height and prevents oversized or sooting flames after LP conversion
• Helps burners light reliably and maintain even heat
• Works as part of an approved LP conversion to match appliance fuel type

• Turn off gas supply and power before starting any gas appliance service
• Use the correct orifice size and follow the appliance LP conversion instructions or service manual
• Hand-tighten and then torque per manufacturer spec if provided; avoid overtightening