Kitchenaid Wall Oven Parts

Gas range and cooktop surface burner knob. Color: Almond. Measures about 2 inches in diameter. For black order WP3181304. For white order WP3181305.

This electronic control board manages core oven functions. It processes keypad inputs and controls heating so the oven starts, regulates temperature, and responds consistently when the original control has failed.

• Regulates oven heating cycles and sends power to bake and broil circuits
• Interprets keypad/touchpad selections to run chosen functions
• Uses oven sensor feedback to help maintain set temperatures
• Can help with symptoms like no heat, bake/broil won't start, unresponsive controls, or control-related error codes

• Disconnect power at the breaker or unplug the appliance before servicing
• Electrostatic-sensitive part—use ESD protection and handle the board by the edges
• Note/photograph wiring and move connectors to matching terminals on the new board
• Restore power, set the clock, and verify all oven functions after installation

This replacement roller fits the front or rear position of a slide mechanism, restoring smooth, even movement and reducing noise when a wheel is worn or broken. It helps racks or drawers glide properly and stay aligned. What it does:

• Provides low-friction rolling support for the slide track
• Helps slide-out assemblies move freely without binding or scraping
• Worn or damaged rollers can cause sticking, squeaking, or uneven travel
• Restores proper alignment and smooth operation when replaced

• 1 roller assembly

• Disconnect power and allow the appliance to cool before servicing
• Remove the slide-out assembly; note roller orientation and hardware
• Transfer/reuse existing screws, clips, or retainers as required
• Do not lubricate unless the manufacturer specifies a lubricant

LF, LR, RR Stainless

This replacement door glass is the transparent window panel used in the door assembly. It restores clear visibility and a safe barrier when the original glass is cracked, shattered, or permanently stained between panes.

• Replaces a damaged or broken door window panel
• Restores a clear view through the door
• Helps maintain proper door integrity and safety
• Common signs include cracks, chips, shattered glass, looseness/rattling, or discoloration between panes

• Disconnect power at the breaker; also shut off gas
• Allow the appliance to cool completely before servicing
• Wear cut-resistant gloves and eye protection; handle glass by the edges
• On many models, removing the door and laying it flat on a padded surface simplifies installation; transfer any brackets or trim from the original glass and tighten fasteners evenly

The Noise Filter is an OEM part for Whirlpool built-in wall ovens. It is installed inside the oven cavity near components that produce vibrations, such as the convection fan motor. 

Causes of a faulty noise filter include the degradation of noise-dampening materials over many heating and cooling cycles. Physical damage from accidental impact during cleaning could also compromise its sound-blocking ability.

Symptoms of a bad noise filter include: 

• Excessive buzzing or humming noises emitted from the oven cavity
• Louder than normal fan or component sounds carrying into the kitchen
• Vibrations felt externally on the oven chassis during operation

This OEM replacement fits several Whirlpool, KitchenAid, and Jenn-Air wall oven models.

This reignition spark module controls the surface-burner ignition system, sending high-voltage to the igniters and re-lighting the flame if it goes out. Replace a weak or failed module to restore dependable burner lighting and safety re-ignition.

• Sends high-voltage spark pulses to the surface burner igniters when a knob is turned on
• Stops sparking once flame is detected and re-ignites if the flame is lost
• Helps resolve symptoms such as no spark at the burners, intermittent ignition, or continuous clicking
• Central control for multiple burner ignition circuits

• Disconnect electrical power and shut off gas supply before servicing
• Handle electronics carefully; avoid static discharge
• Note wire locations and terminal labels; move connectors one at a time to the new module
• Mount securely and ensure a proper chassis ground before testing burner ignition

This gas pressure regulator stabilizes incoming supply to your range or oven, delivering consistent burner flames. Replacing a failed regulator can restore proper heat output and reliable ignition across surface, bake, and broil burners.

• Regulates household gas supply to the appliance manifold for stable burner operation
• Helps maintain consistent flame height and heat in the oven and on the cooktop
• Protects downstream gas components from overpressure
• Failure symptoms include weak flames on all burners, oven or broiler not heating, or repeated clicking with no ignition

• Disconnect power, shut off gas supply, and allow the appliance to cool before servicing
• Observe flow-direction/orientation arrows and connect inlet/outlet ports correctly
• Apply an approved gas-rated thread sealant to threaded joints; avoid overtightening
• After installation, leak-test all connections with an approved solution—never use an open flame

Black

This factory replacement filter helps protect your appliance by trapping unwanted debris and contaminants so the system can perform as designed. Replace a damaged or clogged filter to restore proper flow and dependable operation. What it does

• Screens particles to protect internal components and maintain airflow or water flow
• Helps sustain performance and reduce wear on the appliance
• Common signs it's time to replace: reduced flow/venting, lingering odors, or visible damage
• Preventive replacement can help maintain efficiency over time

• 1 filter

• Disconnect power to the appliance; shut off water supply if applicable
• Access and remove the old filter, noting orientation and seals
• Install the new filter fully seated; do not overtighten any fasteners or fittings
• Restore power (and water, if used) and check for proper operation and leaks/airflow

This replacement grill grate restores a sturdy, level grilling surface on your cooktop or range. Replace a cracked, warped, or missing grate to maintain safe support and consistent heat over the grill area.

• Provides the elevated grilling surface above the heat source for stable, even cooking
• Keeps food positioned at the proper height for consistent searing and results
• Replace if cracked, broken, warped, or heavily corroded
• Helps resolve rocking/unstable surface or uneven cooking caused by a damaged grate

• Turn appliance off and allow all surfaces to cool completely before handling
• Lift off the old grate and clean debris from the support ledges or frame
• Set the new grate in the correct orientation; ensure it sits flat and stable
• Verify proper clearance around adjacent components before use

The Motor-Fan is an OEM component specifically designed for Whirlpool kitchen ranges. Located within the back wall of the oven cavity, the motor fan works to circulate air and remove excess moisture and smoke during the cooking process. Proper motor-fan functioning helps ensure efficient oven ventilation and performance.

Symptoms of a bad motor fan include:

• Excessive smoke or moisture left in the oven after cooking  
• Oven taking longer to preheat and cook due to poor air circulation
• Loud buzzing or grinding noises emanating from the fan

Causes of failure are normally wear and tear of motor windings or fan blade bearings from years of continuous use. Overheating can potentially reduce lifespan as well. 

This OEM Whirlpool part is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The burner grate is an OEM part for Whirlpool gas ranges. This grill component sits above the burners to provide an elevated grilling and warming surface. 

Causes of a bad burner grate can include warping or damage from high heat over time, worn or broken tie bars allowing unstable movement, or surface deterioration that makes normal cooking unsafe.

Symptoms of a bad burner grate include: 

• Wobbly or loose resting above the burners
• Pits, sharp edges, or thin spots on the grilling surface  
• Rust or deterioration of structural integrity
• Difficulty removing or installing due to tie bar issues

This OEM part fits select Whirlpool, Maytag, KitchenAid, Jenn-Air,  and Amana models.

This support bracket secures an appliance cabinet component or mounting point to restore alignment and reduce movement. It replaces worn or broken supports so panels and internal parts stay properly positioned during normal operation. What it does

• Holds a cabinet panel, frame, or internal component in place to maintain proper alignment.
• Stabilizes mounting points to help reduce vibration, rubbing, or intermittent noise.
• Common replacement when you notice a loose or sagging panel, rattling, or unusual chassis movement.
• Provides a direct mechanical fix—matches the OEM bracket design and fit.

• Disconnect power (and shut off gas supply for gas appliances) before starting any repair.
• Remove necessary panels and fasteners to access the old bracket; keep track of all screws and clips.
• Compare the new bracket to the old part for orientation before installing; secure using the original fasteners—do not overtighten.

Includes 7 spuds.

This dual infinite switch controls power to a dual surface burner on an electric range or cooktop. Replacing a failed switch restores smooth heat control and proper inner/outer ring selection for accurate simmer-to-boil performance. What it does:

• Regulates power sent to the inner and outer sections of a dual surface element
• Provides variable heat levels from low to high
• Lets you select small (inner) or large (dual-ring) cooking zones
• Common failure symptoms: burner stuck on high or won't turn off, won't heat or heats erratically, cannot switch between inner-only and dual-ring modes

• 1 dual infinite surface element control switch

• Disconnect power at the breaker before servicing
• Access the control panel; remove the knob and switch mounting hardware as required by your model
• Label or photograph wiring and transfer each wire to the same terminal on the new switch
• After reassembly, test both inner-only and dual-ring settings to ensure proper operation