Lg Dishwasher Parts

The Noise Filter Assembly is an OEM part for LG dishwashers. It is designed to reduce electrical noise and interference that can affect the dishwasher's operation. The noise filter helps ensure that the electronic components function smoothly and without disruption, contributing to the overall efficiency and reliability of the appliance.

Causes of a bad noise filter assembly can include electrical surges, wear and tear over time, or damage due to moisture or physical impact.  

Symptoms of a bad noise filter assembly include:

• The dishwasher not starting or stopping unexpectedly
• Error codes related to electrical issues
• Intermittent power loss during a cycle
• Unusual noises coming from the control panel area

This OEM LG part is also compatible with some Kenmore models.

This door-mounted assembly stores detergent and rinse aid and releases them at the proper time in the wash cycle. Replace a cracked or non-dispensing unit to restore consistent detergent release and overall wash performance. What it does:

• Holds detergent and rinse aid within the inner door
• Releases detergent during the main wash cycle
• Meters rinse aid during the final rinse
• Helps prevent leaks at the dispenser opening
• Common symptoms: detergent left in cup, rinse aid not dispensing, dispenser door won't open, leaks or visible cracks

• One dispenser assembly

• Disconnect power and shut off water supply before servicing
• Remove inner door panel to access and replace the dispenser
• Transfer any reusable seal or hardware from the original part
• After installation, run a short cycle and check for leaks around the dispenser

This lower spray arm (nozzle assembly) mounts at the bottom of the tub and spins to deliver pressurized wash water across dishes. Replacing a cracked or clogged arm restores even spray coverage and helps resolve poor cleaning results.

• Distributes wash water from the pump across the lower rack area
• Rotates to provide even spray coverage and rinsing
• Replaces warped, cracked, or clogged arms that reduce cleaning or cause noise
• Common symptoms: dishes not getting clean, spray arm not turning, visible damage or blockages

• Disconnect power at the breaker; open the door and remove the lower rack
• Release the old arm from the center hub (turn/unsnap retainer) and lift off
• Clear debris from the hub and filter area; seat the new arm fully and verify free rotation
• Restore power and run a short cycle to proper spray action

This nozzle assembly directs high-pressure wash water through its jets for even cleaning inside the dishwasher. Replacing it restores consistent spray coverage and wash performance. What it does:

• Distributes wash water through spray jets during wash and rinse cycles
• Uses water pressure to rotate and reach all rack areas
• Replaces broken, warped, or clogged nozzles that restrict flow
• Common symptoms include poor cleaning results, spray arm not spinning, unusual noise, or leaks at the spray hub

• 1 nozzle assembly

• Disconnect power and water supply before servicing
• Pull out the rack as needed; release the locking tab or nut to remove the old nozzle
• Inspect and transfer any O-rings/gaskets if present; seat the new assembly fully for a leak-free seal
• Run a short test cycle to check for leaks

This hose connector joins an appliance hose to its mating port for a secure, leak-resistant connection. Replace a cracked or loose connector to stop drips at the joint and restore reliable flow through the line.

• Provides a secure coupling between a hose and an appliance fitting or another hose
• Helps maintain a tight seal to prevent leaks at the connection point
• Supports proper flow during fill, circulation, or drain operations
• Helps resolve issues such as dripping at the joint, a hose that won't stay attached, visible cracking, or intermittent fill/drain performance

• Disconnect power and, if applicable, shut off the water supply before servicing
• Place towels to catch residual liquid and relieve line pressure
• Transfer and tighten clamps or O-rings per your model; seat hoses fully on the connector
• Run a short test and inspect for leaks before returning the appliance to service

The Holder is an OEM part for LG dishwashers. This clip is designed to secure the tine rows in place, ensuring that your dishes and utensils are held securely during the washing cycle. It provides a reliable hold for the tine rows, preventing them from shifting or falling out during operation.

Symptoms of a bad retainer clip include:

• Loose or wobbly tine rows
• Difficulty in loading or unloading dishes
• Missing or lost retainer clips

A bad retainer clip can occur due to wear and tear, damage, or loss. If you notice symptoms such as loose or wobbly tine rows, difficulty in loading or unloading dishes, or missing retainer clips, it's time to replace the faulty or missing retainer clip with this genuine OEM part.

This LG replacement part is also compatible with Sears/Kenmore models.
 

This gasket creates a watertight seal between mating parts in the dishwasher's water system. Replacing a worn or damaged seal helps stop leaks during cycles and maintains proper wash performance. What it does:

• Seals the joint between components such as the sump, pump housing, or inlet assemblies
• Prevents water leakage under pressure during fill, wash, and drain
• Helps maintain spray pressure by reducing internal bypass
• Common symptoms include water on the floor or in the base pan, and a flattened, cracked, or brittle old gasket

• One gasket

• Disconnect power and turn off the water supply before servicing
• Access the gasket location and remove any retaining hardware
• Remove the old gasket and clean both sealing surfaces thoroughly
• Seat the new gasket evenly without twisting; tighten fasteners/clamps uniformly and run a test cycle to check for leaks

This small sleeve bushing supports a pivoting or rotating joint in your dishwasher, providing a smooth bearing surface. Replacing a worn bushing helps restore quiet operation and protects mating parts from further wear. What it does

• Provides a low-friction surface between a shaft/pin and bracket
• Helps maintain proper alignment and reduces wobble at the joint
• Can quiet squeaks or grinding caused by wear
• Replacing a cracked or flattened bushing can improve smooth movement

• 1 bushing

• Disconnect power and shut off water before servicing
• Support the door or component attached to the joint to relieve tension
• Note orientation; transfer any spacers/washers in the same order
• Inspect the mating pin/shaft for wear and replace related parts if damaged

This pump casing assembly forms the sealed housing around the pump, channeling water through the system. Replacing a cracked or warped casing helps stop leaks and restore proper water flow and overall pump performance.

• Houses the pump impeller and seals the pump chamber to contain water
• Directs water flow between the tub/sump and the pump for efficient operation
• Helps maintain proper water pressure within the pump circuit
• Common symptoms of a failing casing include leaks near the pump area, weak water movement or poor draining, unusual grinding/rumbling noises, or visible cracks/warping

• Disconnect power and shut off water supply before servicing
• Access the pump (typically from the bottom or rear)
• Transfer any existing O-rings, clamps, and screws as needed; clean sealing surfaces
• Reassemble carefully, reconnect hoses, and run a test cycle to check for leaks

This thermistor holder secures the temperature sensor in place inside the dishwasher, ensuring accurate water temperature readings for proper wash and dry performance.

• Holds the thermistor securely in the sump/tub area
• Helps the control accurately monitor wash water temperature
• A loose or missing holder can cause temperature-related wash issues
• Common symptoms include temperature errors or poor cleaning/drying when the sensor isn't properly positioned

• Disconnect power and turn off water supply before servicing
• Access the sensor location from the tub/sump area; note original orientation
• Transfer the thermistor into the new holder and snap the holder into place
• Inspect the sensor wiring and seals while reassembling

This door latch and lock assembly secures the dishwasher door and signals the control that it's safely closed. Replacing a worn latch restores firm door closure, a reliable seal, and consistent cycle operation. What it does:

• Locks the door so cycles can start and continue without interruption
• Helps compress the door gasket for a proper, leak-resistant seal
• Sends a door-closed signal to the control
• Common symptoms: won't start with the door shut, door won't latch or pops open, cycle pauses when jostled, water leaking at the door edge

• One door latch/lock assembly

• Disconnect power at the breaker before servicing
• Remove the inner door panel to access the latch at the top of the door
• Note wire connector positions; move them to the new assembly and secure the latch
• Check latch engagement with the strike and adjust alignment if needed before reassembly

This impeller assembly spins on the dishwasher's pump to move water through the system. Replacing a worn or broken impeller restores proper water flow, helping maintain wash performance and reducing noise from the pump area. What it does:

• Moves water through the dishwasher's pump system for circulation and cleaning
• Helps maintain correct water flow and spray pressure to the spray arms
• Typical failure signs: poor cleaning or weak spray, unusual grinding/humming from the sump, or slow/no draining depending on which impeller has failed
• Physical clues include damaged/broken blades or a loose fit on the motor shaft

• 1 impeller assembly

• Disconnect power and turn off the water supply before servicing
• Remove the lower rack and filters to access the pump/sump; follow your model's service information
• Note the impeller's orientation; transfer any reusable seals or hardware from the original as required
• After reassembly, check for leaks and verify the pump spins freely before running a test cycle

This component is a sump and motor assembly that is designed to be used on a dishwasher. This part moves the water from the sump collection area up into the spray arms.When the sump and motor assembly is faulty, the dishwasher may leak from the bottom. It is also possible that the dishwasher could run noisily. This high-quality OEM replacement part will fix these problems. If unsure if this part will fix the problems, consult a professional. Disconnect the appliance from the electrical outlet before performing care, maintenance, or replacing any parts on it. Some people performing this replacement may wish to wear work gloves to protect their hands during this process. The replacement process is very easy and takes about 15 to 30 minutes to complete from start to finish.This sump and motor assembly is compatible with dishwashers that are manufactured by LG. It is sold individually and sourced from the manufacturer.

This replacement switch cam interfaces with a lever or knob to actuate a microswitch. It restores reliable on/off signaling and the positive feel/engagement of the related control or latch mechanism when the original cam wears or cracks.

• Translates lever or rotary motion into precise switch activation
• Ensures the switch travels fully to open and close as intended
• A worn or broken cam can cause intermittent operation or functions that won't start/stop as expected
• Helps bring back a defined "click" or detent at the control/lever

• Disconnect power to the appliance before servicing; turn off gas/water if applicable
• Access the switch or latch assembly; remove any knob, trim, or cover as needed
• Note the cam's orientation/indexing before removal; take photos for reference and transfer any springs/clips
• After reassembly, manually test the mechanism to ensure smooth switch actuation before restoring power

This dishwasher sump gasket seals the joint between the sump assembly and the tub to prevent leaks and maintain wash performance. Replace it if the old seal is worn, flattened, cracked, or damaged to stop water escaping beneath the unit.

• Creates a watertight seal where the sump attaches to the tub
• Helps prevent water leaks from the base of the dishwasher
• Supports proper circulation and overall wash performance
• Common failure signs: puddles under the unit, leaks during a cycle, or a visibly torn/deformed gasket

• Disconnect power and turn off the water supply before servicing
• Access the sump from inside the tub (remove lower rack, spray arm, filters, and sump cover) or from below, depending on model
• Clean mating surfaces; install the new gasket evenly without twists or gaps
• Reassemble and run a short cycle to check for leaks

Sump assembly collects and channels a washer's drained water into the drain pump to let the machine empty properly. Replacing a worn or cracked sump helps stop leaks and restores normal draining performance. What it does:

• Directs and funnels tub water to the drain pump so the washer can evacuate water.
• Prevents water from leaking under the washer when intact and properly sealed.
• Can cause poor or no draining, standing water in the tub, or drain/pump-related error codes when damaged.
• May produce unusual noises during the drain cycle if cracked or clogged.

• Disconnect power and turn off water supply before starting any repair.
• Access typically requires removing the washer's front or lower access panel; support the machine as needed.
• Inspect and replace any worn seals, hoses, or clamps when installing to ensure a watertight fit.
• After installation, run a short drain/spin cycle and check for leaks before returning the washer to regular use.