Lg Refrigerator Parts

The Refrigerator Air Filter Cover is an OEM replacement part for LG refrigerators. It provides a protective casing for the refrigerator's air filter. The air filter cover makes filter replacement easy while allowing uniform airflow distribution for optimal cooling and freshness. 

Causes of a bad air filter cover can include cracks or breaks from normal use over time. Screws or securing mechanisms may also become loose.

Symptoms of a bad air filter cover include:

• Cool air escaping without circulating properly
• Inability to easily access the air filter for replacement  
• Excessive refrigeration coil or evaporator fan noise

This OEM LG part is also compatible with Sears/Kenmore models. 

This hinge lever mounts on the refrigerator door hinge to guide door movement and closure, helping the door seal properly. Replacing a worn or broken lever restores smooth operation and consistent sealing.

• Guides hinge motion so the door opens and closes smoothly
• Helps maintain door alignment for a reliable gasket seal
• Replace if the lever is visibly cracked, worn, or deformed

• Disconnect power and support the door to prevent injury or damage
• Remove the hinge cover and fasteners; note the lever's orientation before removal
• Install the new lever in the same position and reassemble the hinge components
• Adjust hinge per model procedures if needed

This water line holder secures and routes the refrigerator's plastic water tube so it stays protected and out of the way. Replacing a damaged holder helps prevent kinks and leaks and keeps water flowing to the dispenser and icemaker.

• Anchors and guides the water tube along the cabinet/door to prevent rubbing and kinking
• Helps maintain proper water flow to the dispenser and ice maker
• Replace if the holder is cracked, missing, or the tube won't stay seated
• Symptoms can include leaks or drips near the hinge/backs, slow or no dispensing, or visibly loose tubing

• Disconnect power and turn off the household water supply before servicing
• Access the holder (often behind a hinge cover, kick plate, or rear panel)
• Note tube routing, then release/remove the old holder and seat the tube in the new holder; reuse existing hardware if present
• Restore water and power; check for leaks and normal dispenser/ice operation

The Ice Maker Assembly is an OEM component specifically designed for LG refrigerators. It is responsible for automatically producing batches of ice cubes on demand. 

Causes of a bad ice maker assembly can include failures in the ejector mechanism that dispenses ice, damage or leaks in the water supply components, or issues with the control board that manages the timing of each cycle. 

Symptoms of a bad ice maker assembly include:

• Failure to produce ice cubes
• Incomplete or misshapen ice cubes  
• Excessive noise during operation
• Water leaks from the ice maker area

This OEM LG replacement part is also compatible with Sears/Kenmore models. 

This rail guide assembly replaces the worn guide that supports and directs a refrigerator drawer or bin. Installing a new guide restores smooth, level travel and helps prevent sticking, jamming, or misalignment during everyday use.

• Guides the drawer/basket for smooth opening and closing
• Helps keep the drawer level and properly aligned on its track
• Replaces cracked, warped, or broken guide assemblies
• Can address sticking, binding, scraping noises, or a drawer that comes off track

• Disconnect power and remove contents from the affected compartment
• Pull out and remove the drawer/bin; retain screws or clips
• Install the new guide in the same orientation; transfer any reusable hardware from the original part if needed
• The drawer glides smoothly before reloading and restoring power
• Some models use separate left and right guides—match orientation to your model's parts diagram

This condenser fan assembly circulates air across the condenser coils and compressor to remove heat from the refrigeration system. Replacing a failing fan helps restore efficient cooling performance and protects the compressor from overheating. What it does:

• Draws air through the condenser coils to dissipate heat
• Supports proper system pressures and overall cooling efficiency
• Helps maintain stable temperatures in both compartments
• Common symptoms include the fan not running, loud noise from the rear, warm cabinet temperatures, or a very hot compressor area

• Pre-assembled fan motor with blade and mounting bracket

• Disconnect power before servicing; use gloves to protect against sharp edges
• Access the lower rear compartment and remove the back cover to reach the fan
• Note wire positions; move over any reusable grommets or screws and secure the assembly firmly
• The blade spins freely and is oriented to move air across the condenser; clean coils before restoring power

The Freezer Drawer Gear is an OEM part for LG refrigerators. It facilitates the smooth operation of the freezer drawer, allowing it to slide in and out effortlessly.

You should replace this gear if it becomes worn or damaged. Causes of a bad freezer drawer gear can include regular wear and tear, damage from overloading the drawer, or mechanical issues due to improper alignment or installation.

Symptoms of a bad freezer drawer gear include:

• Difficulty in opening or closing the freezer drawer
• The drawer not staying aligned or level
• Unusual noises when operating the drawer

This OEM LG part is also compatible with Sears/Kenmore.

This condenser fan motor spins the cooling fan that draws air across the condenser coils and around the compressor. Replacing a weak or seized motor restores proper heat removal so the refrigerator can hold temperature and run more efficiently. What it does:

• Drives the condenser fan to move air through the rear condenser/compressor compartment
• Helps dissipate heat from the refrigerant and protects the compressor from overheating
• Supports stable internal temperatures and efficient cooling performance
• Common symptoms: fan not running, louder rattling/grinding at the back-bottom, hot cabinet sides, warmer-than-normal refrigerator temperatures

• Includes 1 cooling fan motor

• Disconnect power before servicing; pull the unit away from the wall for access
• Remove the rear lower access panel to reach the condenser fan area
• Note wiring and fan-blade orientation; transfer the blade and any mounting hardware from the old motor as needed
• The fan spins freely and airflow direction matches the original before reassembly

RAIL,SLIDE-LEFT

The Screw is an OEM part for LG refrigerators. This part secures the shelf brackets within the refrigerator compartment.

Causes of a bad Screw can range from physical damage or impact to general wear and tear over time. 

Symptoms of a faulty Screw  include:

• Shelves feeling loose or unstable
• Shelves sagging or not sitting level
• Shelves falling out or collapsing when loaded with items

This OEM LG part is also compatible with some Kenmore models.

This turntable roller ring sits under the glass tray and allows it to rotate smoothly for even heating. Replace a worn, warped, or broken ring to restore stable rotation and consistent cooking performance.

• Supports the glass turntable and rides on built-in rollers for smooth, quiet movement
• Keeps the tray level and centered to promote even heating
• Common symptoms: tray not turning, uneven cooking, scraping/grinding noises, or a wobbly/slipping turntable
• Restores proper interaction between the turntable, drive coupling, and motor

• Unplug the microwave or switch off the breaker before servicing
• Remove the glass tray; lift out the old ring and clean the track
• Place the new ring with the rollers facing down on the track; reseat the tray on the center drive coupling
• Test rotation with a microwave-safe cup of water

This display case is the molded housing for the refrigerator's control panel. It supports and aligns the user interface components and trim, restoring a secure, finished fit when the original case is cracked, broken, or out of shape.

• Positions and supports the display/selector board and buttons in the panel opening
• Provides mounting points for panel trim and fasteners
• Helps shield internal components from dust and incidental moisture
• Common signs it's needed: cracked or broken plastic, missing tabs, loose or misaligned control panel

• Unplug the refrigerator before servicing
• Remove the panel/trim per your model's procedure; note screw and clip locations
• Carefully handle the user interface board and wiring; avoid static discharge and pinched harnesses
• Transfer any brackets or clips from the old case to the new one, then reassemble and test

This flexible perimeter seal keeps the refrigerator door closing tight so cold air stays in and warm air stays out. Replacing a worn or warped gasket helps restore stable temperatures, reduce frost and condensation, and improve overall efficiency.

• Creates an airtight seal around the door to maintain interior temperature and humidity
• Helps prevent condensation, sweating, and frost at the door opening
• Restores proper door closure when the old seal is torn, deformed, or compressed
• Common symptoms: visible gaps or cracks, moisture around the door, temperature fluctuations, longer run times

• Disconnect power and clear items from door bins before servicing
• Pull the old gasket from the retaining channel; some models require loosening retainer screws
• Clean the channel/mating surface; warm the new gasket with hot water or low heat to relax folds
• Seat the new gasket starting at the corners, then along the sides; close the door and check for even contact all around

This ice bucket assembly stores and delivers ice to the dispenser. Replacing a damaged bucket restores smooth, reliable dispensing and helps prevent jams when the original container is cracked, worn, or no longer engaging the drive.

• Stores finished ice beneath the icemaker and positions it for dispensing
• Interfaces with the dispenser drive to move ice into the chute when activated
• Helps maintain proper alignment for consistent cube delivery
• Common symptoms: cracked or broken container/tabs, ice won't dispense or jams, grinding/skipping during dispense

• Disconnect power to the refrigerator before servicing
• Remove the old bucket; empty ice and note the drive coupler orientation
• Seat the new assembly fully so the drive engages; transfer any reusable covers from the original if needed
• Restore power and test ice dispensing

The LED Assembly is an OEM part for LG refrigerators. This part provides clear visibility to help users easily locate items. The LED assembly is energy-efficient and designed to last longer than traditional light bulbs.

Causes of a bad LED assembly can include electrical malfunctions, power surges, or exposure to moisture that can damage the electronic components.

Symptoms of a bad LED assembly include:

• Dim or flickering lights inside the refrigerator
• Complete lack of lighting when the door is opened
• Intermittent lighting that turns on and off unexpectedly

This OEM LG part is also compatible with some Kenmore models.