Lg Washer Dryer Combo Parts

Secures the spider assembly to the inner drum in your washer. Replace if bolt is stripped, loose, or missing to restore secure mounting and reduce noise.

Washer won't spin or agitate? A faulty stator assembly disrupts the magnetic field needed to drive the motor. Restores normal drum rotation.

Lint filter screen for washer dryer combos. Replace when clogged to prevent drain errors and maintain proper airflow. Verify fit with your model number.

Replaces worn or torn door boot gasket that seals your washer drum. Replace if you notice water leaks, mold buildup, or visible cracks. Confirm fit.

Inlet hose for washers. Connects water supply to machine. Replace if cracked, leaking, kinked, or worn. Essential for proper water flow to drum.

Inlet hose connects your washer to the water supply. Replace if cracked, leaking, worn, or damaged to restore proper water flow to your machine.

Inlet hose connects your washer to the water supply. Replace if cracked, leaking, worn, or damaged to restore proper water flow to your machine.

Pressure sensor air chamber for washers. Connects the tub to the water level switch. Replace if cracked, clogged with detergent residue, or leaking air.

This Thermostat Assembly monitors and regulates internal temperature within the appliance's heating circuit. Replacing a failed thermostat restores proper heat control, helps prevent overheating, and can resolve common heating performance issues so cycles run correctly. What it does

• Senses internal temperature and opens/closes the heater circuit to maintain proper heat
• Provides over-temperature protection by cutting power at unsafe temperatures
• Helps ensure consistent heating performance throughout the cycle
• Helps with symptoms such as no heat, overheating/shutting off, or unusually long cycle times

• 1 thermostat assembly

• Disconnect power before servicing; allow hot components to cool
• Access the thermostat location (varies by model); note wire positions before removal
• Mount flush to the surface for accurate sensing; transfer original hardware if required
• After installation, test operation; use a multimeter for continuity checks if needed

This is a flexible rubber bellows that connects the dryer exhaust outlet to the external vent duct on a combination washer/dryer unit. It channels hot, moist air out of the dryer section and helps absorb vibration during operation. Replace this bellows if it is cracked, torn, or collapsed, which can cause poor drying performance, excessive lint buildup, or moisture leaking inside the unit.

This is a plastic lifter baffle that mounts inside the dryer drum. It tumbles and lifts clothes as the drum rotates, promoting even airflow and efficient drying. Replace this part if it is cracked, broken, or missing, which can result in clothes bunching together, uneven drying, or loud thumping noises during operation.

This clamp secures hoses or wiring to the appliance chassis to prevent movement, chafing, and vibration-related wear. It helps keep connections stable so hoses and wires stay in place during normal use. What it does:

• Holds water, drain or vent hoses in position to reduce strain and prevent rubbing
• Keeps wiring harnesses routed and fastened to avoid chafing or accidental disconnection
• Reduces vibration-related noise caused by loose hoses or wires
• Helps prevent hose kinks and unintended movement that can lead to leaks or intermittent electrical issues

• One clamp

• Disconnect power to the appliance before servicing; shut off water supply if working with water lines
• Remove panels as needed to access the hose or wiring route, then replace the clamp in the same orientation
• Use appropriate pliers or a screwdriver if required; do not overtighten or deform the hose or wiring
• If the original clamp was secured with a fastener, retain and reuse it only if undamaged; replace any stripped or broken hardware

Rear housing panel that shields internal components and maintains airflow. Replace this outer cover if cracked, broken, or missing to restore protection.

Drum bearing bushing for washers. Installs between drum and bearing assembly. Replace if cracked, worn, or missing to restore proper drum support.

Cabinet base assembly for washers. Replaces cracked, rusted, or corroded base frames. Installs at bottom of washer cabinet to support unit weight.

Washer door boot bellows seals the tub opening. Replace if torn, moldy, or causing black marks on clothes. Confirm fit with your model number.