Parts for Bosch B36IT70NNP/08: Lightning Parts

This active carbon filter refreshes the air when your range hood is set to recirculate. Replace a saturated filter to restore effective odor reduction and maintain a more comfortable cooking space. What it does:

• Adsorbs cooking odors in recirculating operation
• Helps maintain fresher indoor air when venting back into the room
• Restores odor-removal performance when the old filter is saturated
• Typical signs it's time to replace: persistent cooking smells or diminished odor reduction

• One activated carbon filter

• Disconnect power to the hood before servicing
• Remove the metal grease filter(s) to access the charcoal filter
• Release the old filter from its clips/bayonet mount and install the new filter in the same orientation until it locks
• Charcoal filters are not washable; replace when saturated

• For hoods configured for recirculation; not used when vented to the outdoors

The Water Filter is an OEM part for Bosch refrigerators. This part removes impurities and contaminants from the water supply to your appliance. This part ensures that the water and ice dispensed by your refrigerator are clean, taste fresh, and are free of common waterborne particles and substances. 

Over time, the water filter can become clogged with sediments and contaminants, reducing its effectiveness and potentially affecting the taste and quality of the water and ice. Regular replacement is essential for maintaining optimal performance.

Symptoms of a bad Water Filter include:

• Unpleasant taste or odor in the water or ice
• Decreased water flow to the dispenser or ice maker
• Visible particulate matter in the water or ice cubes

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

A replacement door hinge that restores proper alignment and smooth opening/closing for affected appliance doors. Helps stop sagging, uneven gaps, and dragging doors so the appliance seals and operates more reliably. What it does:

• Supports the door and provides the pivot point for opening and closing
• Restores proper door alignment to correct sagging or uneven gaps
• Reduces binding, rubbing, or noisy operation when the door moves
• Helps the door seat fully to maintain an effective seal

• Disconnect power (and water, if applicable) and remove shelves or panels as needed before starting.
• Support the door while removing or installing the hinge to prevent dropping or damage.
• Use basic hand tools; follow the correct procedure and torque.
• If your model uses matched hinges, consider replacing the pair to maintain even alignment.

This decorative trim strip restores the finished look of a dishwasher door by covering the edge of the front panel and providing a clean, factory appearance. It's a direct-fit cosmetic replacement for worn, chipped, or missing door trim. What it does:

• Covers and protects the exposed edge of the dishwasher door for a seamless appearance
• Hides gaps and damaged overlay on the door front to improve overall look
• Helps keep the door panel edge aligned and prevents further chipping or wear
• Common symptom: visible damage, missing trim, or an uneven door edge

• One decorative trim strip (1 piece)

• Disconnect power to the appliance before starting any repair
• Typically installs with clips or screws along the top/bottom edge of the door—retain original fasteners when possible
• Handle trim and door panel edges carefully to avoid cuts or cosmetic damage

This small replacement clip secures appliance components to restore proper fit and stop loose parts from shifting during use. It's a direct-fit replacement designed to hold trim, panels, or assemblies where the original clip failed. What it does:

• Holds small panels, trim pieces, or assemblies in place to prevent rattling and misalignment
• Restores the original mounting point so doors, drawers, or covers sit flush
• Helps keep wiring, hoses, or small parts secured and routed correctly
• Stops intermittent contact that can cause noise or wear on adjacent components

• One replacement clip

• Disconnect power and water before servicing
• Verify clip location and orientation against the existing fastener before removal
• Remove broken clip and press new clip into the same mounting slot; some clips may snap or slide into place

This support is a replacement mount bracket used to secure internal components and maintain proper alignment in the appliance. It restores stable support where a worn or broken bracket causes misalignment or movement. What it does:

• Provides structural support for internal assemblies to prevent sagging or shifting
• Helps keep racks, rails, or panels aligned for smooth operation
• Reduces noise caused by loose or damaged mounting points
• Restores correct part positioning that can affect performance or wear

• One support bracket

• Disconnect power and water to the appliance before starting any repair
• Use appropriate hand tools and handle sharp edges carefully

This water inlet valve controls water flow into the appliance, restoring proper fill and preventing unwanted leaks. Replacing a faulty inlet valve returns normal water supply and helps the appliance fill reliably. What it does:

• Opens and closes the water supply to the appliance when a cycle calls for water
• Stops water flow when the fill is complete to prevent overfilling
• Common symptom: appliance won't fill or fills slowly
• Common symptom: continuous or intermittent leaking near the inlet area
• Works with the appliance's control signals to regulate fill volume

• Disconnect power and shut off the water supply before starting any repair
• Drain residual water from hoses and fittings to avoid spills
• Inspect and replace any worn inlet hoses or seals when replacing the valve

This halogen oven light bulb replaces the interior lamp so you can clearly see inside your oven for cooking and cleaning. It restores oven illumination when the light is burnt out or dim. What it does

• Provides interior oven illumination for checking food and oven cavity condition
• Replaces a burned-out or flickering oven lamp
• Restores consistent brightness for safer monitoring of cooking progress
• Fits in compatible oven lamp sockets designed for halogen bulbs

• One halogen oven light bulb

• Turn power to the appliance off and allow the oven and old bulb to cool completely before replacing
• Use a cloth or gloves when handling the bulb to avoid skin oils on the glass, which can shorten bulb life
• Push or twist the bulb into the socket as required by your oven's lamp holder; do not force

This is a replacement micro switch used in select Bosch-built appliances. It opens and closes an electrical circuit when actuated by a lever or cam, enabling functions like starting/stopping a cycle or detecting a position.

• Controls power or signals by opening/closing a low-voltage circuit when pressed
• Commonly used for on/off, door/lid, or position-sensing functions
• Failure may cause the unit not to start, intermittent operation, or features that won't engage
• May also present as unresponsive buttons or functions that only work when pressed a certain way

• Disconnect power before servicing; verify no voltage is present
• Access location varies by model; remove panels as needed to reach the switch
• Note wire positions and terminal orientation before removal
• Test continuity with a meter after installation to ensure proper operation