Parts for Bosch B36IT70NNP/08: Doors Assembly Parts

This active carbon filter refreshes the air when your range hood is set to recirculate. Replace a saturated filter to restore effective odor reduction and maintain a more comfortable cooking space. What it does:

• Adsorbs cooking odors in recirculating operation
• Helps maintain fresher indoor air when venting back into the room
• Restores odor-removal performance when the old filter is saturated
• Typical signs it's time to replace: persistent cooking smells or diminished odor reduction

• One activated carbon filter

• Disconnect power to the hood before servicing
• Remove the metal grease filter(s) to access the charcoal filter
• Release the old filter from its clips/bayonet mount and install the new filter in the same orientation until it locks
• Charcoal filters are not washable; replace when saturated

• For hoods configured for recirculation; not used when vented to the outdoors

The Water Filter is an OEM part for Bosch refrigerators. This part removes impurities and contaminants from the water supply to your appliance. This part ensures that the water and ice dispensed by your refrigerator are clean, taste fresh, and are free of common waterborne particles and substances. 

Over time, the water filter can become clogged with sediments and contaminants, reducing its effectiveness and potentially affecting the taste and quality of the water and ice. Regular replacement is essential for maintaining optimal performance.

Symptoms of a bad Water Filter include:

• Unpleasant taste or odor in the water or ice
• Decreased water flow to the dispenser or ice maker
• Visible particulate matter in the water or ice cubes

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This fixture is the OEM mounting bracket used to secure internal components inside the appliance, keeping assemblies aligned and stable for reliable operation. It replaces a broken or worn bracket to restore proper fit and reduce movement. What it does

• Secures and positions internal parts to prevent shifting or rattling during operation
• Restores proper alignment of assemblies that rely on the bracket for support
• Can help stop intermittent noises or misfeeds caused by a loose or broken mount
• Protects adjacent components by holding parts in the correct location

• One fixture (mounting bracket) as shown

• Always disconnect power and water before starting repairs
• Typical installation requires basic hand tools; avoid overtightening plastic fasteners
• If damaged surrounding fittings are present, inspect and replace them to ensure a secure fit

This fixture is a small mounting clamp that secures internal components in place to keep them aligned and stable during normal appliance operation. It helps reduce movement and vibration for a quieter, more reliable appliance. What it does:

• Holds internal assemblies or wiring harnesses securely to prevent shifting
• Keeps parts properly positioned to maintain function and reduce wear
• Helps reduce rattling or vibration caused by loose components
• Supports safe, consistent operation by keeping components from contacting other parts

• Disconnect power and water supply before accessing internal components
• Basic hand tools may be required to remove panels and fasten the fixture
• Inspect surrounding clips and fasteners; replace any that are damaged

The Mullion Heater is an OEM part for Bosch refrigerators. It is designed to prevent condensation from forming on the refrigerator door mullion, the vertical divider between the doors. This heater ensures that the mullion stays warm enough to stop moisture from condensing and causing potential water damage or mold growth.

Causes of a bad mullion heater can include electrical failures, wear and tear from continuous use, or manufacturing defects.  

Symptoms of a bad mullion heater include:

• Visible condensation or frost on the door mullion
• Water pooling or dripping around the door area
• Increased humidity inside the refrigerator
• Mold or mildew developing near the door seal

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This is a mounting fixing kit used to secure specific dishwasher components. It replaces worn or missing hardware so parts stay firmly in place and the appliance operates as intended.

• Secures designated parts to prevent loosening, rattling, or misalignment
• Helps resolve issues like loose panels or components shifting during cycles
• Useful when original fasteners are stripped, corroded, or lost
• Restores proper fitment after service or replacement of related parts

• Disconnect power and turn off water before servicing
• Keep track of original hardware locations for correct reassembly
• Hand-start screws to avoid cross-threading; tighten to snug, do not overtighten
• Address corrosion or damage present on mating parts before installation

This perimeter door seal fits into the dishwasher tub channel along the sides and top of the door. It contains wash water and steam to help prevent front leaks and ensure proper door compression.

• Seals the gap between the door and tub on the sides and top
• Helps stop water drips at the front corners and along the door edge
• Reduces escaping steam and moisture at the door area
• Common signs of wear: leaks from the door, visible tears/flattening, musty odor, or the door not sealing smoothly

• Disconnect power and turn off the water supply before servicing
• Open the door, pull the old gasket straight out; clean the channel of debris and residue
• Find the midpoint of the new seal at the top center and press it evenly into the channel down both sides without stretching
• Close the door to help seat the seal, then run a test cycle and check for leaks

This factory repair set provides the factory-specified components needed to restore proper operation of compatible Bosch appliances. It replaces worn or damaged service parts so the appliance can perform as intended. What it does

• Replaces the original service components supplied in the repair set to restore normal function.
• Helps stop symptoms caused by worn parts, such as loose fittings, intermittent operation, or minor leaks when those parts are affected.
• Restores proper alignment or mounting where included components secure moving parts.
• Useful when troubleshooting issues traced to the specific assembly the kit services.

• Disconnect power and, if applicable, water supply before beginning any repair.
• Follow the manufacturer's service instructions and use only the supplied components.
• Inspect surrounding parts for wear; replace additional damaged components as needed.

The Door Seal is an OEM part for Bosch refrigerators. This part maintains the refrigerator’s internal temperature by creating a tight barrier around the door, preventing cold air from escaping and warm air from entering.

Causes of a bad door seal can include normal wear and tear, damage from frequent opening and closing, exposure to fluctuating temperatures, or buildup of dirt and debris.

Symptoms of a bad Door Seal include:

• Visible cracks, tears, or deformation on the seal
• Condensation or frost buildup inside the refrigerator
• Refrigerator running more frequently
• Warm spots inside the refrigerator

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This profile stripe is a replacement door trim strip that restores the finished look of the appliance and protects the door edge from chips and wear. It's a direct-fit exterior trim designed to match the original appearance. What it does

• Replaces a worn, cracked, missing, or scratched door trim stripe to restore cosmetic appearance
• Covers the junction between door panels and provides a finished edge
• Helps protect the door edge from everyday dings and moisture at the seam
• Restores proper fit and alignment of visible trim for a factory look

• Use basic hand tools; remove power to the appliance and follow OEM instructions before starting
• Handle trim carefully to avoid marring the finish; clip or adhesive locations may be fragile
• If adhesive is used, allow proper cure time per adhesive manufacturer instructions

This profile stripe is a replacement door trim strip that restores the finished look of the appliance and protects the door edge from chips and wear. It's a direct-fit exterior trim designed to match the original appearance. What it does

• Replaces a worn, cracked, missing, or scratched door trim stripe to restore cosmetic appearance
• Covers the junction between door panels and provides a finished edge
• Helps protect the door edge from everyday dings and moisture at the seam
• Restores proper fit and alignment of visible trim for a factory look

• Use basic hand tools; remove power to the appliance and follow OEM instructions before starting
• Handle trim carefully to avoid marring the finish; clip or adhesive locations may be fragile
• If adhesive is used, allow proper cure time per adhesive manufacturer instructions