Parts for Kitchenaid KRFF300ESS01: 03 - Liner And Ice Maker Parts

Reduces contaminants in ice and water. Replace every 6 months for optimal filtration. Simple twist-out installation. Verify fit by model number.

Stops refrigerator fan rattling and buzzing noise. This rubber grommet cushions the fan motor to reduce vibration. Simple DIY fix, takes under 30 minutes.

Replace your refrigerator door gasket to restore a tight seal and prevent air leaks. Worn gaskets cause energy loss and temperature issues. Verify fit.

Replacement cabinet housing for your refrigerator. Restores structural integrity when the original is cracked, damaged, or broken. Encloses components.

Interior lights staying on or not working? This door switch controls refrigerator lighting and functions. Moderate DIY repair with video guide available.

Refrigerator not cooling or defrosting? This evaporator wire harness restores electrical connections for defrost and fan circuits. Moderate DIY repair.

Front cover panel for bottom-mount refrigerators. Replaces cracked, broken, or missing exterior cover. Restores finished appearance to unit.

Fix a warm fridge or freezer that won't stay cold with a new evaporator fan motor. This motor circulates air over cooling coils. Easy DIY repair in under an hour.

Fridge not cooling but freezer works? A worn evaporator fan blade prevents cold air circulation. Easy 15-minute DIY fix with our video guide.

Outer shell housing that protects the control panel electronics. Replace when cracked, broken, or cosmetically damaged to restore appearance.

LED light module illuminates your refrigerator interior. Replace when lights become dim, flicker, or stop working entirely. Verify fit with your model.

Refrigerator too warm or freezer icing up? A faulty thermistor prevents proper temperature regulation. This 5-minute fix restores accurate cooling.

Replacement screw that secures panels, brackets, and trim to appliance cabinets. Restores reliable hold when original hardware is stripped or missing.

Refrigerator too warm or uneven temps? This air tower assembly channels cold air from evaporator to compartments. Fixes airflow issues in 30-45 minutes.

Cracked or missing ice maker cover exposing internal components? This protective cover shields the ice maker assembly. Simple DIY install in minutes.

Refrigerator light won't turn off or on? The door switch detects when the door opens and closes. Easy 5-minute DIY repair with a pick tool or scraper.

Refrigerator cover panel that installs on the exterior or interior surface. Replace this part if the original is cracked, broken, or missing.

Fix slime buildup or weak water flow from your refrigerator dispenser. This water reservoir tank stores and chills water for ice and water dispensing.

Ice maker not making ice or leaking? This complete ice maker kit replaces corroded contacts and faulty assemblies. DIY-friendly installation in 30-60 minutes.

Note: If the harness provided in the kit does not work with your refrigerator, remove the harness from your existing ice maker and reuse it.

Shields and positions the temperature sensor for accurate readings. Replace if cracked, broken, or missing to restore proper sensor placement and airflow.

This grille holds the refrigerator air filter in place behind the toe kick, allowing proper airflow through the filter and helping control odors. It replaces a damaged or missing grille to restore correct filter fit and operation. What it does:

• Secures the air filter housing so the filter seals and functions as intended
• Permits airflow through the filter media for odor control and fresher interior air
• Covers and protects the filter opening from debris and accidental contact
• Restores proper fit and appearance to the fridge front toe-kick area

• Disconnect power to the appliance before beginning any work
• Remove the old grille by gently pulling or releasing retaining clips as required by your model
• Align the grille with the filter opening and press until clips engage; do not force
• If an air filter is separate, verify the filter is seated correctly inside the grille before restoring power

Fix unresponsive controls or erratic cooling cycles with this refrigerator electronic control board. Restores user interface and temperature management.

This is a metal heat shield designed to protect internal components from excessive heat inside the refrigerator or freezer compartment. It acts as a thermal barrier, typically installed near the defrost heater or compressor area, preventing heat damage to surrounding parts. Replace this shield if it is warped, corroded, or missing, which can lead to uneven cooling or frost buildup.

This orifice is a small precision component used in the refrigerator's cooling system to regulate refrigerant or gas flow. It is typically located near the evaporator or cooling circuit and helps control the rate at which refrigerant enters the evaporator coil. Replace this part if the refrigerator or freezer section is not cooling properly, frost patterns are uneven, or a technician has identified a restricted or damaged orifice during diagnosis.

Replacement fastener screw for appliances. Secures panels, trim, clips, and components. Needed when original screws are stripped, missing, or damaged.

Secures internal components in your refrigerator to keep parts stable and prevent rattling. Replace if bent, broken, or missing to restore alignment.

Secures and shields the freezer light assembly. Replace if cracked, broken, or missing to restore proper light protection and a clean appearance.

Fix dim or unprotected interior lighting with a new light lens. Covers and protects the bulb while diffusing light evenly. Simple DIY swap.

Replace a worn or damaged light socket to restore reliable interior lighting. Fixes flickering bulbs and intermittent power issues. Confirm fit by model.

Replacement access panel cover for refrigerators. Restores exterior finish and shields internal components. Needed when original is cracked, broken, or missing.

Fix uneven cooling or temperature issues between compartments with this refrigerator damper housing. Secures the air damper and directs airflow properly.

Air tower assembly for bottom-mount refrigerators. Directs cold air throughout the fresh food compartment. Replace if cracked, broken, or missing pieces.

This is a cover assembly that fits over the water dispenser area on the front of the refrigerator. It protects the internal dispenser components and provides a finished appearance on the exterior of the door. Replace this cover if it is cracked, broken, discolored, or if it no longer snaps securely into place.

Fix a leaking or clogged water dispenser with this rigid water tube. Restores proper water flow to your dispenser and ice maker. Direct replacement.

Replace a cracked or missing control panel switch cover on your refrigerator. Covers switches, protects from spills, and restores a clean appearance.

This limit switch monitors a set condition and opens or closes its contacts when that limit is reached. Replacing a failed switch restores proper safety cutoff and consistent operation of the appliance's heating or movement system. What it does:

• Senses a limit condition at its mounting point (such as temperature or travel/position, depending on model)
• Changes state at a defined threshold to protect components and wiring
• Interrupts power to heat or motor circuits, or signals a control to respond
• Common failure signs: no heat or shuts down early, runs continuously, won't start, or intermittent operation

• 1 limit switch

• Disconnect power to the appliance before servicing
• Note wire positions; transfer connectors one at a time or take a photo for reference
• Reinstall in the original orientation so the actuator or sensing surface contacts the correct area
• Address root causes (blocked airflow, binding mechanisms, shorted components) to prevent repeat failures

Replacement cover for refrigerators. Shields internal components and maintains appearance. Order when original is cracked, broken, or missing.

Connects ice maker to freezer wiring. Replace if wires are pinched, damaged, or connector is broken. Installs between ice maker and freezer cavity wall.

Ice maker won't stop making ice or arm keeps falling off? This shut-off arm senses bin levels to control production. Simple snap-in installation.

Ice dropping throughout freezer? Replace your cracked or warped ice storage bin to prevent spills and jams. Direct-fit part keeps cubes contained.

Evaporator coils freezing up or freezer not defrosting? A faulty thermistor may be the cause. This temperature sensor regulates defrost cycles. DIY repair.