Parts for Ge GNE25JMKGFES: Machine Compartment Parts

Reduces chlorine, lead, cysts, and pharmaceuticals for clean water and ice. Replace every 6 months or when filter light activates. Verify fit by model.

Directs defrost water from the evaporator to the drain pan below your refrigerator. Replace if cracked, damaged, or clogged to prevent water pooling.

Secures refrigerator wiring to prevent chafing and vibration noise. Replace when damaged or missing to keep harnesses organized. Confirm fit by model.

Mounting standoff spacer secures internal components, panels, and circuit boards inside your refrigerator. Replace if cracked, broken, or missing.

Seals icemaker water supply tubes and prevents air leaks in your refrigerator. Replace if you notice frost buildup, water leaks, or ice production issues. Verify fit with your model number before ordering.

Cardboard or metal cover that closes the machine compartment opening on your refrigerator back panel. Replace if cracked, missing, or water-damaged.

Fix electrical failures in your refrigerator's lower cabinet with this wiring harness. Connects components for proper operation. Moderate DIY repair.

Fix a refrigerator that won't cool or runs constantly with this compressor kit. Essential for restoring proper cooling in refrigerators and freezers.

Fix a refrigerator that won't cool properly with a new condenser assembly. This component releases heat to keep your fridge running efficiently.

Secures panels and trim pieces inside your refrigerator. Replaces broken or missing retainers that cause loose trim, rattling, or misaligned components.

If your refrigerator runs but doesn't cool or fails to start, the compressor start device may have failed. This relay and overload combo helps restore cooling.

The R134 Drier is an OEM part for GE refrigerators. This component plays a critical role in the refrigeration system by removing moisture and contaminants from the refrigerant, ensuring efficient cooling and preventing damage to other parts of the system. It helps maintain the purity and effectiveness of the refrigerant as it cycles through the system.

You should replace the R134 drier if it becomes clogged or damaged. Common causes of a bad drier include wear and tear over time, exposure to moisture, or contamination from other failing components in the refrigeration system.

Symptoms of a bad R134 drier include:

• Reduced cooling efficiency
• Frost buildup on the evaporator coils
• Unusual noises from the refrigeration system
• Increased energy consumption
• Refrigerator not maintaining the set temperature

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

A threaded mounting bolt that secures the compressor to the refrigerator's frame, providing vibration dampening and structural support. Replace when you hear excessive compressor noise, vibration, or notice the compressor appears loose or misaligned.

Replacement mounting screw for securing panels, trim, and internal components in appliances. Needed when original screws are stripped, lost, or damaged.

Plastic cover that conceals and protects water supply tubing behind the lower kickplate. Replace if cracked, broken, or missing for a finished look.

Fix icemaker overflow or no water/ice issues with this water isolation valve kit. Controls water flow to your icemaker. DIY-friendly, 20-minute repair.

Refrigerator not cooling or defrosting? A failed main control board disrupts cooling cycles and temperature regulation. Moderate DIY repair restores function.

Protective housing for your refrigerator's main control board. Replace if cracked, broken, or missing to secure wiring and electronic components.

This sound damper cushions the refrigerator compressor to reduce vibration and minimize noise for quieter operation. It helps protect the compressor from metal-on-metal contact and dampens normal operating sounds. What it does:

• Cushions compressor mounting to absorb vibration and reduce noise
• Prevents metal-on-metal contact that can cause rattling or buzzing
• Helps stabilize the compressor to reduce wear from vibration
• Commonly used when compressor noise, rattling, or increased vibration is noticed

• One sound damper

• Always disconnect power to the appliance before beginning any repair
• Access the compressor area (rear lower cabinet); remove any panels as needed
• Remove the old damper and press the replacement onto the compressor mounting foot until fully seated
• If mounting hardware is damaged or the compressor mount appears worn, replace mounting parts.

10-32 x 5/16 machine-thread screw secures refrigerator panels, trim, and internal brackets. Replaces missing or damaged fasteners to prevent rattles.

Hex washer head screw for securing refrigerator components. Replace if screw is stripped, missing, or damaged during maintenance or repair work.

Mounting screw for refrigerator interior components like fan brackets, ice maker assemblies, and shelving. Replace if stripped, missing, or corroded.

Refrigerator running hot or not cooling properly? This condenser fan and housing assembly circulates air over condenser coils to dissipate heat and restore efficient cooling.

Internal water supply tube for refrigerators. Routes water between components inside the unit. Replace if cracked, split, or leaking at fittings.

Secures the condenser fan motor in position. Replace this bracket if cracked, bent, or causing excessive vibration to restore stable mounting.

Rubber grommet that seals and cushions where the evaporator fan motor shaft mounts. Replace if cracked, worn, or missing to eliminate noise and vibration.

Rear condenser fan mounting bracket for refrigerators and freezers. Replaces broken, cracked, or missing brackets that secure the fan assembly.

Secures and seals water line connections in your refrigerator's dispensing system. Replace if leaking or loose to prevent water damage. Confirm fit.

Refrigerator running hot or making loud noises? A worn condenser fan blade prevents proper airflow across coils. DIY repair in 30 minutes or less.

Fix a refrigerator that's not cooling or has an overheated compressor. This condenser fan motor circulates air over the compressor and coils. DIY-friendly.