Parts for Ge GTH18CCEDRBB: Machine Compartment Parts

Refrigerator condenser felt tape seals and insulates the condenser area. Replace when worn, torn, or losing adhesion to maintain efficiency. Verify fit with your model number before ordering.

Mounting screw secures door handles to refrigerator doors. Replace if missing, stripped, or broken. Requires allen wrench for installation. Essential hardware.

Vinyl sleeve that fits over rods, tubes, or wires in your refrigerator. Replace if cracked, torn, or missing to protect contact points and reduce wear.

Fix a refrigerator that freezes food or runs too cold with this temperature control thermostat. Common DIY repair with video guide, typically done in 10-15 minutes.

Attaches to the control shaft to adjust temperature settings. Replace this knob if yours is cracked, broken, or missing to restore smooth control operation.

Molded frame that supports and protects refrigerator control components. Replace if cracked, broken, or damaged to restore proper alignment and secure mounting.

This foam housing cushions and insulates the refrigerator control assembly to reduce vibration and help protect wiring and components. It restores proper mounting support and helps maintain stable operation of the control area. What it does:

• Cushions the control module to minimize vibration-related noise and wear
• Provides thermal insulation around the control area to reduce heat transfer
• Helps hold wiring and components in position to prevent rubbing or chafing
• Can address symptoms such as rattling or loose-feeling control assemblies

• One foam housing for the control assembly

• Install only on power-off appliance; unplug or switch off circuit breaker before servicing
• Verify the foam aligns with control-module mounting points and wiring harness openings
• Replace only with matching part number to ensure fit; handle foam gently to avoid tearing

Refrigerator light not working? This light bulb socket holds the bulb securely and provides electrical connection. Easy DIY repair with video guide.

Interior light not working when door opens? This light switch controls refrigerator illumination. DIY-friendly install takes 30-45 minutes with video.

Fix a warm fridge or freezer ice buildup. This defrost heater melts frost on evaporator coils to restore cooling. Moderate DIY repair, 1-2 hours.

Freezer icing up or fridge too warm? The defrost thermostat monitors evaporator temperature to prevent frost buildup. DIY repair in under an hour.

Fixes uneven cooling or frost buildup caused by a misaligned defrost heater. This holder assembly secures the element in place. 15-minute repair.

This drip shield deflects and channels condensation and meltwater away from sensitive components to help reduce puddling and ice buildup inside the refrigerator. It's a direct-replacement exterior shield for the evaporator/defrost area. What it does

• Channels defrost meltwater into the drain path to prevent pooling under shelves or crispers.
• Helps reduce ice buildup by directing water away from cold surfaces.
• Protects internal components and wiring from moisture exposure.
• Can resolve symptoms like visible water inside the fresh-food section or intermittent dripping.

• Disconnect power to the appliance before starting any repair.
• Typically installs with a few screws or snap tabs; keep fasteners from the original part for reassembly.
• Handle gently to avoid cracking the plastic; replace if warped or damaged.

Supplies electrical power from wall outlet to refrigerator. Replace this cord if cut, frayed, overheated, or damaged to restore safe electrical connection.

Secures refrigerator wiring to prevent chafing and vibration noise. Replace when damaged or missing to keep harnesses organized. Confirm fit by model.

Refrigerator not cooling or ice building up on evaporator coils? The defrost timer controls the defrost cycle. DIY-friendly, installs in 5 minutes.

Fix noisy or squealing sounds from the back of your fridge with a new condenser fan motor. Typical DIY repair takes 8-10 minutes with basic tools.

Fix a noisy or broken condenser fan blade in your refrigerator. Common DIY repair that typically takes 20-30 minutes. Includes step-by-step video guide.

Secures and seals water line connections in your refrigerator's dispensing system. Replace if leaking or loose to prevent water damage. Confirm fit.

Replacement clip retainer for refrigerators. Secures internal components in place. Order a new retainer if yours is cracked, broken, or missing.

Refrigerator not cooling or compressor clicking on and off? This compressor kit restores cooling. Requires certified technician with specialty tools.

Freezer not cooling or frost buildup? This evaporator coil absorbs heat to maintain cold temperatures. Professional repair recommended due to refrigerant.

Provides start and run voltage to the compressor. Replace if cracked, damaged, or failing. Installs near the compressor at the bottom of the unit.

Fix a refrigerator that won't cool and clicks every few minutes. This start relay and overload assembly mounts on the compressor to restore reliable starting.

Refrigerator clip secures components in place. Replace if broken, loose, or causing rattling noises. Verify fit with your model number before ordering.

Replacement door shelf bin for top-mount refrigerators. Installs on the fresh food door to hold bottles and condiments. Replace if cracked or broken.

Replacement shelf support stud for refrigerator shelves. Installs to hold shelves in place. Needed when original stud is broken, cracked, or missing.

Replacement mounting screw for securing panels, trim, and internal components in appliances. Needed when original screws are stripped, lost, or damaged.

Hex washer head screw for refrigerators, freezers, and other appliances. Replaces lost, stripped, or damaged screws during repairs or panel assembly.

Secures the condenser unit in your refrigerator. Replace if loose, broken, or causing vibration noise. Verify fit with your model number before ordering.