Magic Chef Parts

This refrigerator compressor circulates refrigerant to cool the appliance and restore proper temperatures. Replaces a failed compressor to help the refrigerator maintain set temperatures when the cooling system is compromised. What it does:

• Pumps refrigerant through the sealed cooling system to enable heat exchange and cooling.
• Runs the refrigeration cycle so the refrigerator and freezer can reach and hold target temperatures.
• Common symptom linkage: fridge not cooling, compressor humming or not running, or frequent cycling.
• Can cause system pressure issues if damaged or leaking.

• One compressor (single sealed unit)

• Power should be disconnected before beginning work and the refrigerant must be recovered per regulations.
• System evacuation, leak testing, and proper recharge with the correct refrigerant are necessary after replacement.
• May require replacement of mounting hardware, start device, or filter-drier—verify system condition during service.

This heating element kit replaces a failed heating element to restore normal heating in compatible laundry or cooking appliances. It provides the core heating component needed to get your appliance producing heat again. What it does:

• Replaces a damaged or burned-out heating element that stops the appliance from heating
• Helps resolve symptoms like no heat, weak or inconsistent heating, or tripped thermal cutouts
• Restores the appliance's ability to reach and maintain operating temperatures for normal cycles
• Works as the direct replacement heating component shown in OEM parts listings

• One heating element kit as shown

• Disconnect power (unplug or shut off breaker) before servicing to avoid shock risk
• Handle the element and terminals carefully to avoid bending or damaging mounting tabs
• Confirm correct terminal connections and secure mounting per the appliance wiring diagram

Color: White.

This rear support assembly stabilizes the appliance's rear housing and helps keep internal components aligned for smooth operation and reduced vibration. It restores proper rear-end support to prevent rubbing, noise, and uneven motion. What it does:

• Provides a stable mounting point for the appliance's rear section to maintain alignment
• Reduces vibration and rattling caused by a loose or worn rear support
• Helps prevent rubbing, scraping, or grinding noises from misaligned components
• Restores proper fit between the rear housing and moving parts to promote smooth operation

• One rear support assembly

• Disconnect power (and gas if applicable) before beginning any repair
• Access typically requires removing the appliance's rear panel or cabinet; follow OEM service manual steps
• Inspect surrounding mounting hardware and replace any worn fasteners for a secure fit

This cycle thermostat regulates temperature during appliance heating cycles to help maintain safe, consistent operation and proper cycle performance. It replaces a worn or failed thermostat to restore correct temperature control. What it does:

• Senses and opens/closes at set temperatures to control heating during cycles
• Prevents continuous heating when the thermostat reaches its limit
• Can cause no-heat, overheating, or short cycling when faulty
• Works with the appliance's control system to maintain cycle timing and safety

• Disconnect power to the appliance before inspecting or replacing the thermostat
• Handle thermostat and terminals carefully; avoid bending sensing elements

This replacement ice tray holds and releases frozen cubes for a refrigerator icemaker, restoring normal ice production and cube release. Durable molded plastic fits the icemaker assembly and resupplies the ice bin with uniformly sized cubes. What it does

• Holds water while it freezes to form individual ice cubes.
• Releases formed cubes to the ice bin when the icemaker cycles, restoring proper dispensing.
• Commonly used when trays are cracked, warped, or no longer shedding cubes.
• Helps resolve symptoms like leaking inside the freezer, misshapen cubes, or reduced ice output.

• One replacement ice tray.

• Turn off power to the refrigerator or unplug before service to avoid injury.
• Remove ice bin and any retaining clips or fasteners to access the tray; handle gently to avoid damage.
• Inspect surrounding icemaker components for wear; replace additional damaged parts as needed.

This high-limit thermostat is a temperature safety switch that helps prevent overheating by opening the circuit when temperatures exceed safe limits. It restores normal operation once the temperature cools, protecting the appliance and reducing fire risk. What it does:

• Monitors internal temperature and opens the circuit if heat gets too high
• Prevents overheating that can cause damage or burn odors
• Commonly replaces a failed or intermittently tripping thermal safety switch
• Works as part of the appliance's temperature-safety system, not a primary temperature control

• Disconnect power to the appliance before attempting replacement
• Observe proper wiring orientation and secure terminal connections
• Replace only with the exact part specified for your appliance

Sealer for refrigerant line insulation.

This ground wire provides a safe chassis connection to restore proper grounding and reduce shock and electrical-fault risk. It replaces a frayed, corroded or missing ground lead to help keep the appliance electrically safe. What it does

• Connects the appliance chassis to the grounding system to prevent stray voltage on metal surfaces
• Restores a secure ground path if the original wire is broken, loose, or corroded
• Helps stop intermittent power faults or nuisance tripping caused by a compromised ground
• Addresses symptoms like visible wire damage, loose ground connection points, or grounding-related electrical issues

• One ground wire

• Always disconnect power (unplug or shut off the circuit breaker) before starting work
• Attach the ring/terminal ends to the designated chassis ground screw and the equipment ground point
• Route the wire away from moving parts, heating elements, and sharp edges; secure with existing clips or fasteners
• If terminal hardware is missing or damaged, replace with equivalent OEM-style fasteners and torque to specification

A stabilizer bracket that secures and supports internal components to reduce movement and rattle during operation. Helps restore stable alignment so the appliance runs quieter and more reliably. What it does:

• Provides structural support to help keep assemblies aligned and reduce excessive movement
• Dampens vibration and minimizes knocking or rattling noises tied to loose components
• Restores proper fit where a worn or broken bracket allowed shifting or misalignment
• Works as a repair for symptoms like intermittent noise, excess vibration, or parts that sag or shift

• Disconnect power (and water if appliance-specific) before beginning any repair
• Basic hand tools are usually required; refer to your model's service manual for exact steps
• Inspect surrounding parts for wear while replacing the bracket

This condenser grommet cushions and secures the refrigerator condenser assembly, reducing vibration and preventing metal-to-metal contact. It helps keep the condenser stable for quieter operation and longer component life. What it does:

• Isolates condenser from the cabinet to reduce rattling and vibration noise
• Prevents condenser edges from rubbing or wearing against the chassis
• Helps maintain proper condenser alignment for efficient airflow
• Commonly replaced when cracked, torn, or missing and causing noise or movement

• Disconnect power before servicing the appliance.
• Support the condenser assembly before removing or installing the grommet to avoid stress on tubing.
• Push the grommet into position; replace any grommets that are brittle or deformed.

This is a genuine replacement mounting screw used to secure panels and components on compatible Whirlpool appliances. It restores proper fastening where a damaged or missing screw causes loose panels or rattling. What it does:

• Secures panels, brackets, or internal parts to restore a tight fit
• Stops vibration-related noise caused by loose fasteners
• Replaces stripped, damaged, or missing screws for safe operation
• Matches the OEM thread and head style for correct fit and torque

• Use the matching screwdriver or driver bit to avoid cam-out or head damage
• Hand-start the screw to align parts before final tightening
• Do not overtighten; stop when parts are snug to avoid stripping threads
• Disconnect power to the appliance before accessing internal panels

This spring element support secures and stabilizes a range or oven heating element to keep it properly positioned for consistent heating and safe operation. It replaces a worn or broken support that allows an element to sag or vibrate. What it does:

• Holds the bake/broil heating element in the correct position so it heats evenly
• Prevents the element from sagging, touching the oven cavity, or rattling during use
• Helps maintain correct element clearance to reduce arcing and uneven cooking
• Addresses symptoms like a loose or wobbly element, unusual noises, or intermittent heating

• One spring element support

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Handle the heating element and support carefully to avoid bending or damaging the element
• Verify correct part orientation against the oven's wiring diagram during installation

This idler pulley guides and maintains tension on the dryer drive belt so the drum spins smoothly and quietly. Replacing a worn pulley restores proper belt tracking and helps prevent belt wear or breakage. What it does:

• Maintains correct tension and alignment of the drive belt
• Reduces squealing or grinding noises from a worn pulley bearing
• Prevents belt slipping and uneven drum rotation
• Helps avoid premature belt wear or burning rubber smells

• Disconnect power to the appliance before starting any work.
• Access may require removing the dryer front or cabinet panels and releasing the belt; follow your model's service instructions.
• Inspect the belt and drum support for wear and replace if needed while servicing.
• Use basic hand tools.

This control knob replaces a worn, broken or missing range/stove control knob to restore safe, simple temperature and function selection. It provides a direct fit and the tactile stop-and-click feel users expect from factory knobs. What it does:

• Replaces a damaged or stripped control knob so the burner or oven settings can be selected accurately.
• Restores grip and rotation for reliable on/off and temperature selection.
• Helps eliminate slipping or poor engagement between the shaft and knob.
• Fits original control shafts to maintain intended control detents and positioning.

• Turn power and gas off before servicing controls; follow appliance manufacturer safety instructions.
• Pull old knob straight off the control shaft; align new knob on the splines and press firmly until seated.
• If knob does not fully seat or rotates loosely, confirm shaft type and knob orientation before forcing.