Mastercut Log Splitter Parts

This is a bushing made from black plastic with a cleft down the middle to provide enough flex for easy insertion. It has a flanged design, which means it won’t easily pop out after installation, even under stress from constant vibration. The bushing’s primary purpose is to protect wires and cables from damage as they pass through a channel. As such, the material is fairly durable and does not need to be replaced under ordinary circumstances. That said, there are some situations in which it can become damaged. For one thing, it’s easy to damage while repairing the wires or cables that run through the bushing. If the bushing does need to be replaced, it requires disconnecting any cables or wires that run through the bushing. Pop out the old bushing with a rubber mallet, install the new bushing the same way, reconnect the wires, and the repair is complete. This is an OEM part sourced directly from MTD, and it is sold individually. It was initially used on snowblowers but has also been used on lawnmowers and lawn tractors.

Thumb screw that secures the air cleaner assembly on lawn mower and small engines. Replace if damaged, stripped, or missing due to vibration.

A fuel cap assembly is a component often seen on lawnmowers and other lawn and garden equipment. It is made of durable black plastic and is used to ensure that fuel doesn’t spill out of the fuel tank. Over time, fuel cap assemblies can begin to wear out and cause problems. Sometimes this results in a cap that doesn’t tighten all the way or there may be a fuel smell when using a lawnmower or snowblower. If fuel is leaking, the cap doesn’t fit right, or the cap seems damaged, it’s best to replace it with a new component. This is a simple process that involves removing the original fuel cap assembly and fitting the new assembly to the lawn machine. This fuel cap assembly is a genuine OEM component that comes directly from the manufacturer. It is an individual part that is compatible with MTD, Murray, Cub Cadet, Bolens, Yard-Man, and Yard Machines lawnmowers, snowblowers, chipper shredders, and tillers. No tools are required to replace this component.

Ignition coil for small engines on lawn and garden equipment. Replace if cracked, damaged, or worn. Includes spark plug boot and wire assembly.

Engine won't start or pull cord slips? This starter cup connects the recoil mechanism to start your engine. Simple bolt-on replacement part.

Governor spring for small engines on lawn mowers, tillers, blowers, log splitters, and chippers. Replace if stretched, broken, or missing for proper throttle control.

This is an authentic OEM replacement part sourced directly from the manufacturer for use in various small engines. This oil fill tube assembly is part of the oil delivery system. This tube delivers the oil to the oil tank when it is added to the engine. If this tube cracks or deteriorates over time, the oil will not make it to the oil tank or the engine. This could lead to complete engine failure if the leak is not discovered. Oil on the driveway or lawn or smoke coming from under the engine when the lawnmower is running is a sure sign that the tube may need to be replaced.The oil fill tube assembly also houses the dipstick which is used to check the oil level in the mower. If the assembly is leaking, the reading won't be accurate and the lawnmower may be operated without adequate oil which can damage the engine. A screwdriver is needed to replace the oil fill tube. Do not replace this part until the engine has cooled. This oil fill tube assembly is made of black molded plastic and sold as an individual unit. It is designed for use in lawnmowers and other small engines manufactured by Toro, Tecumseh, and Briggs & Stratton.

Fuel cap for gas-powered engines and outdoor power equipment. Seals fuel tank to prevent debris, dirt, and air contamination. Replace if cracked or loose.

This silencer plate is used on a variety of outdoor lawn and garden machines to reduce the noise from the air intake. This molded plastic part sits on top of the carburetor and houses the air filter. It provides an added layer of noise muffling. Exposure to wind, rain, and heat can cause the plastic to become brittle and cracked. The silence plate should be replaced if damage is discovered during routine maintenance. A screwdriver is needed to replace the silence plate. Before working on the machine, make sure the engine is cool and remove the spark plug. Remove the air filter cover and the air filter to access the silencer plate. Remove the screws holding the plate in place. Install the new silencer plate. Tighten the screws. Install the air filter and housing cover. This silencer plate is made of durable molded plastic and is sold individually. It is a genuine OEM replacement part sourced directly from the manufacturer. This part is compatible with tillers, chippers, shredders, and small engines manufactured by Cub Cadet, MTD, and Yard Machines.

Plastic cover that snaps over the air filter assembly on lawn and garden engines. Replace if cracked, broken, or missing to protect the filter from dirt.

Hex head bolt that secures components together on lawn tractors and outdoor power equipment. Replace if damaged, stripped, or missing to restore assembly.

Replace worn, cracked, or missing handle grips on your lawn mower or snow blower. Restores comfortable control and cushioning to equipment handles.

Bell washer for lawn mowers and tractors. Installs to secure components and prevent loosening. Replace if cracked, worn, or missing for proper assembly.

Shield spacer for lawn tractors and riding mowers. Provides proper spacing and alignment for protective shields. Replace if missing, damaged, or worn.

This part is a replacement push cap. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. If the current push cap is broken or has been misplaced, this part can be used as a replacement. It is intended for use with several lawnmower models.The push cap is attached to the wheel hub cap and fits over the end of the axle shaft. This helps to protect the end of the shaft and the attached bolt that holds the wheel into position. When working on or near an engine, always ensure that the equipment is powered off and completely cooled down before attempting to undergo any repairs. For more accurate information on how and where to install this push cap, the appropriate owner's manual and equipment diagrams should be referred to. This push cap is suitable for use on a variety of lawnmower models manufactured by MTD, Yard Machines, Craftsman, Yard Man, and Troy-Bilt. It is a genuine OEM part and thus is made of high-quality, durable materials. This part is sold individually.