Maytag Cooktop Valve

This gas valve controls the flow of gas to a burner, enabling safe ignition and precise flame adjustment. Replacing a worn valve restores smooth knob operation and consistent flame performance on your gas cooking appliance.

• Opens and closes to start/stop gas flow to a specific burner
• Works with the control knob to modulate flame size
• Helpful when a burner won't light despite spark/ignition present
• Can address issues like inconsistent flame or a knob that's hard to turn

• Disconnect power and shut off the gas supply before servicing
• Match the orientation and connections to the original valve
• Use an approved gas-rated thread sealant on threaded fittings
• After installation, check all joints for leaks with a soap-and-water solution

This gas surface burner valve regulates fuel flow to a cooktop or range burner for safe ignition and smooth flame control. Replace a worn or sticking valve to restore consistent flame adjustment and reliable knob operation.

• Regulates gas to the surface burner; opens/closes as the control knob is turned
• Helps resolve no-flame or no-ignition conditions when sparking is present
• Restores proper flame adjustment from low simmer to full boil
• Addresses stiff, seized, or inconsistent valve action at the knob

• Disconnect electrical power and shut off the gas supply before servicing
• Remove the knob and access the manifold to detach the old valve; note tubing and orientation
• Transfer any mounting clip or fittings from the original valve if required by your model
• After reassembly, check all connections with an approved leak-detection solution and verify burner operation

Replacement burner valve that controls gas flow to a surface cooktop burner, restoring reliable flame control for safer, consistent cooking. Use this valve when a burner has low or no flame, uneven flame, or won't respond to knob adjustments. What it does:

• Regulates gas flow to a single surface burner so you can adjust flame size and cooking heat.
• Replaces valves that cause burners to fail to light, produce weak or sputtering flames, or not change flame level.
• Restores normal burner operation when the original valve is worn, leaking, or damaged.
• Compatible with gas cooktops and ranges.

• Turn off the gas supply and unplug the appliance before starting any repairs.
• Use appropriate hand tools; avoid overtightening fittings or damaging gas lines.
• After installation, check all connections for leaks (soap-and-water test) and verify proper burner ignition and flame.

This burner valve controls the flow of gas to a single surface burner, restoring proper burner ignition and heat control. It's a direct-replacement gas valve that helps fix intermittent or no-flame burner operation. What it does:

• Regulates gas flow to one surface burner so the burner lights and the flame responds to the control knob.
• Replaces a valve that is stuck, leaking, or not allowing gas through, which can cause a burner to fail to light or produce a weak/unsteady flame.
• Works with pilot/ignition systems to ensure consistent ignition when the knob is turned.
• Helps eliminate clicking or continuous sparking caused by failed gas delivery (when ignition sequence is otherwise OK).

• One burner valve

• Turn off the gas supply and unplug the appliance before starting any work.
• Verify valve orientation and connections match your appliance.
• Use approved fittings and check all gas connections for leaks with a soap solution or gas leak tester after installation.
• Do not attempt repairs if you smell gas; ventilate the area, avoid open flames.

A replacement surface burner valve that controls gas flow to a cooktop burner for consistent flame and heat. Restores proper burner response so burners light and adjust as expected. What it does

• Regulates gas flow to a single surface burner so flame size responds to the control knob
• Helps resolve a burner that won't light or produces little or uneven flame
• Replaces a worn or faulty valve that causes inconsistent temperature during cooking
• Use with the corresponding manifold and control knob assembly for full operation

• One burner valve (surface)

• Turn off gas supply and disconnect power before servicing; follow all safety procedures
• Inspect connections and fittings for proper sealing; check for leaks after installation with a soap solution
• Handle components carefully to avoid damage to valve ports and threads