Cooktop Valve

The Gas Valve Cooktop is an OEM part for Bosch cooktops. This valve is responsible for controlling the flow of gas to the burners on the cooktop. It opens and closes to allow gas to pass through when a burner is turned on and stops the flow of gas when the burner is turned off. 

Causes of a bad gas valve can include wear and tear over time, issues with the valve mechanism such as stuck or blocked components, or damage from exposure to moisture or impact. 

Symptoms of a bad gas valve include:

• Burners not lighting or sparking repeatedly without igniting 
• Uneven or unpredictable burner flame heights
• Burners not getting hot enough for cooking
• Burners that cannot be turned on or off
• Gas leaks around the valve area

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore cooktop models. 
 

Restore smooth, controllable flame on a gas cooktop burner. This surface burner valve regulates gas flow to an individual top burner, allowing precise adjustment from low simmer to full boil and helping stop leaks when turned off.

• Controls gas flow to one surface burner
• Common failure signs: burner won't light or is very weak, knob turns hard or feels loose, gas odor at the valve, flame will not adjust smoothly
• Helps ensure reliable ignition and steady flame once replaced

• Disconnect gas and power before servicing; ventilate the area if gas odor is present
• Label and transfer the knob shaft orientation and any mounting hardware from the original
• Check and reuse the correct orifice and inlet fittings from the old valve if required by your model
• After installation, perform a leak check on all connections with approved leak-detection solution

This gas valve controls the flow of gas to a burner, enabling safe ignition and precise flame adjustment. Replacing a worn valve restores smooth knob operation and consistent flame performance on your gas cooking appliance.

• Opens and closes to start/stop gas flow to a specific burner
• Works with the control knob to modulate flame size
• Helpful when a burner won't light despite spark/ignition present
• Can address issues like inconsistent flame or a knob that's hard to turn

• Disconnect power and shut off the gas supply before servicing
• Match the orientation and connections to the original valve
• Use an approved gas-rated thread sealant on threaded fittings
• After installation, check all joints for leaks with a soap-and-water solution

This gas surface burner valve regulates fuel flow to a cooktop or range burner for safe ignition and smooth flame control. Replace a worn or sticking valve to restore consistent flame adjustment and reliable knob operation.

• Regulates gas to the surface burner; opens/closes as the control knob is turned
• Helps resolve no-flame or no-ignition conditions when sparking is present
• Restores proper flame adjustment from low simmer to full boil
• Addresses stiff, seized, or inconsistent valve action at the knob

• Disconnect electrical power and shut off the gas supply before servicing
• Remove the knob and access the manifold to detach the old valve; note tubing and orientation
• Transfer any mounting clip or fittings from the original valve if required by your model
• After reassembly, check all connections with an approved leak-detection solution and verify burner operation

This gas valve assembly controls the flow of gas to the appliance's burners so they ignite and maintain a steady flame. Replace a failing valve to address ignition problems and restore normal heat delivery. What it does:

• Regulates gas flow during ignition and operation to maintain consistent burner flame
• Enables burners to light when the ignition system calls for gas
• A faulty valve can cause burners to fail to light, produce a weak or uneven flame, or result in repeated ignition attempts
• If you smell gas, stop use immediately and follow safety guidance — do not try to power or test the appliance

• Turn off the appliance power and shut off the gas supply before starting work; if you detect a strong gas odor, leave the area
• Basic hand tools may be required; gas and electrical connections must be properly tightened and sealed
• Follow the manufacturer's installation instructions and local codes
• After installation, check for leaks using an approved leak-detection method and verify proper ignition and operation

This replacement valve kit restores proper flow control in compatible GE appliances, helping resolve failures related to supply, dispensing or leaks. It's a direct-replacement style assembly intended to return the affected system to normal operation. What it does:

• Regulates flow to the appliance's system to enable normal filling, dispensing or operation
• Replaces worn seals and moving valve components that can cause intermittent function
• Stops or reduces leaks and unintended flow when the original valve assembly fails
• Helps correct symptoms such as no fill/dispense, intermittent operation, or persistent leaking

• Always disconnect power and, if applicable, shut off the water and/or gas supply before starting
• Handle components carefully; use manufacturer-recommended seals, gaskets and mounting hardware
• Test for leaks and correct operation after installation

This water inlet valve controls water flow to the refrigerator's ice maker and dispenser, restoring normal ice production and water dispensing when the valve fails. Durable direct-fit replacement for affected GE refrigerators. What it does

• Opens and closes to supply water to the ice maker and dispenser when the dispenser or ice maker calls for water.
• Commonly used to fix no-water or low-water flow to the ice maker or dispenser.
• Stops water flow when the refrigerator is off to prevent leaks or flooding.
• Works with electrically controlled solenoid valves in the water system.

• One water inlet valve

• Disconnect power and shut off the household water supply before starting work.
• Access may require removing interior panels, the back cover, or toe panel depending on the model.
• Replace using the existing mounting and wiring connections; use new water line fittings if old fittings are corroded.

This gas surface burner valve controls the right-rear burner on your cooktop or range, regulating gas flow as you turn the knob. Replacing a worn valve restores consistent ignition and precise flame control at that position.

• Regulates gas flow to the right-rear surface burner for on/off and flame level control
• Common symptoms include no ignition, uneven or weak flame, or poor flame adjustment at that burner
• Stiff, loose, or wobbly knob action at the RR position can indicate internal valve wear
• If a gas odor is detected, shut off gas and have the unit serviced before use

• Disconnect power and shut off the gas supply before servicing
• Remove the knob and front panel to access the manifold; note valve orientation and connections
• Support the manifold with a second wrench while loosening/tightening fittings to avoid damage
• After installation, perform a soap-solution leak test on all connections and verify proper ignition and flame

Replacement burner valve that controls gas flow to a surface cooktop burner, restoring reliable flame control for safer, consistent cooking. Use this valve when a burner has low or no flame, uneven flame, or won't respond to knob adjustments. What it does:

• Regulates gas flow to a single surface burner so you can adjust flame size and cooking heat.
• Replaces valves that cause burners to fail to light, produce weak or sputtering flames, or not change flame level.
• Restores normal burner operation when the original valve is worn, leaking, or damaged.
• Compatible with gas cooktops and ranges.

• Turn off the gas supply and unplug the appliance before starting any repairs.
• Use appropriate hand tools; avoid overtightening fittings or damaging gas lines.
• After installation, check all connections for leaks (soap-and-water test) and verify proper burner ignition and flame.

This burner valve controls gas flow to a surface range burner to produce and adjust the flame for cooking. Replacing a faulty valve restores proper ignition and flame control for safe, even heating. What it does

• Regulates gas flow to the surface burner so the flame lights and adjusts with the control knob
• Enables consistent low-to-high flame response for normal cooking
• Can fix symptoms like a burner that won't light, has no flame, or won't hold a steady flame
• Works as the control point between the cooktop control and the burner assembly

• Turn off gas supply and electrical power before starting; follow all safety procedures.
• After installation, check all gas connections for leaks using a proper gas leak test method.
• Do not use the appliance if you detect a gas odor; shut off gas and ventilate area.

This burner valve controls the flow of gas to a single surface burner, restoring proper burner ignition and heat control. It's a direct-replacement gas valve that helps fix intermittent or no-flame burner operation. What it does:

• Regulates gas flow to one surface burner so the burner lights and the flame responds to the control knob.
• Replaces a valve that is stuck, leaking, or not allowing gas through, which can cause a burner to fail to light or produce a weak/unsteady flame.
• Works with pilot/ignition systems to ensure consistent ignition when the knob is turned.
• Helps eliminate clicking or continuous sparking caused by failed gas delivery (when ignition sequence is otherwise OK).

• One burner valve

• Turn off the gas supply and unplug the appliance before starting any work.
• Verify valve orientation and connections match your appliance.
• Use approved fittings and check all gas connections for leaks with a soap solution or gas leak tester after installation.
• Do not attempt repairs if you smell gas; ventilate the area, avoid open flames.

A replacement surface burner valve that controls gas flow to a cooktop burner for consistent flame and heat. Restores proper burner response so burners light and adjust as expected. What it does

• Regulates gas flow to a single surface burner so flame size responds to the control knob
• Helps resolve a burner that won't light or produces little or uneven flame
• Replaces a worn or faulty valve that causes inconsistent temperature during cooking
• Use with the corresponding manifold and control knob assembly for full operation

• One burner valve (surface)

• Turn off gas supply and disconnect power before servicing; follow all safety procedures
• Inspect connections and fittings for proper sealing; check for leaks after installation with a soap solution
• Handle components carefully to avoid damage to valve ports and threads

This burner valve controls gas flow to a cooktop or range burner so the burner lights and adjusts correctly. Replacing a faulty valve restores reliable ignition and steady flame control for safe cooking. What it does:

• Regulates gas flow to a single surface or oven burner for low-to-high flame control
• Helps maintain a steady flame; a worn valve can cause weak, uneven, or no flame
• Can prevent burners from staying lit or from igniting at all when failing
• Works with the range's control knob and gas manifold to deliver the correct fuel flow

• One burner valve

• Turn off the gas supply and unplug the appliance before starting any repair
• Only connect and test gas fittings with a certified gas-safe method; check for leaks after installation
• Tighten connections to OEM torque specs and replace any damaged seals or gaskets

This gas valve controls the flow of natural gas or propane to the oven/range burner, restoring reliable ignition and steady heat for baking and broiling. Direct replacement for failed or leaking valve assemblies. What it does:

• Regulates gas flow to the oven/range burner so the burner lights and maintains temperature.
• Stops gas flow when the safety system detects a fault, preventing unsafe conditions.
• Commonly replaces valves that leak, fail to open, or prevent the oven from heating.
• Helps resolve symptoms like no bake/broil heat, intermittent ignition, or continuous clicking/try-to-light cycles.

• One gas valve assembly.

• Turn off gas supply and electrical power before attempting service; follow local codes.
• Tighten gas fittings to manufacturer torque specs and perform a leak test after installation.
• Some installations may require removing the range/oven front or burner components for access.

The Burner Valve is an OEM replacement part for Whirlpool gas cooktops. It is a critical component that regulates the flow of gas to individual burners on the cooktop surface. Each burner typically has its own dedicated valve, allowing for precise control and adjustment of the gas supply.

Symptoms of a bad Burner Valve include:

• Difficulty igniting or maintaining a consistent flame on the affected burner
• Uneven or irregular flame patterns
• Gas odors or leaks around the burner area
• Burner failing to light at all or extinguishing unexpectedly

Causes of a bad burner valve can range from buildup of debris or clogs obstructing proper gas flow, to mechanical issues such as worn-out valve components or failure of the valve's internal components. Over time, valves can also become damaged or corroded due to exposure to heat and moisture.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore gas cooktop models.