Maytag Dryer Gasket & Seal

The door seal forms the primary gasket around the door opening on horizontal-axis machines, creating a tight barrier that keeps contents contained and prevents gaps that can lead to leaks, odors, and poor performance. What it does

• Seals the perimeter of the door opening to contain wash water and suds
• Helps the door close flush and maintain a consistent, leak-free seal
• Common symptoms: water leaking at the door area, visible tears or cracks in the seal, persistent mildew/odors around the gasket, or a door that won't seal properly

• 1 door seal

• Disconnect power and shut off water supply before servicing
• Remove the front panel/retaining bands as needed to access the seal
• Note orientation and drain holes at the bottom; press the seal fully into its groove all the way around
• Reinstall retainers, ensure the door closes flush, and run a short test to check for leaks

This coupler gasket creates a tight, leak-resistant seal at a coupler connection point, helping maintain proper operation of the assembly. Replace when the original gasket is worn, cracked, or flattened to prevent drips and seepage.

• Forms the seal between a coupler and its mating component
• Helps prevent water seepage and air intrusion at the joint
• Supports correct flow/pressure through the connection
• Common symptoms: drips at the fitting, moisture around the coupler, or needing to over-tighten to stop leaks

• Disconnect power and shut off water supply before servicing
• Relieve line pressure and place a towel to catch residual water
• Clean mating surfaces; seat the gasket squarely in the coupler recess
• Tighten fittings evenly; restore service and check for leaks

Fiberglass-reinforced door seal that restores an appliance door's airtight closure to help maintain consistent temperatures, reduce energy waste and minimize frost or moisture buildup around the door. What it does:

• Forms a continuous gasket around the door to keep cold air in and warm air out.
• Helps prevent frost buildup and uneven temperatures caused by air leaks.
• Common symptoms that indicate replacement: visible gaps, cold-air leakage, frost/ice at the door, or a door that won't seal flush.
• Fiberglass construction helps the seal retain shape for a more reliable long-term closure.

• Disconnect power to the appliance before beginning any service.
• Remove the old seal and clean the door channel; press the new seal evenly into place, checking for full contact around the perimeter.
• Some models may require partial door or liner removal—before disassembly.
• If the seal is stiff, follow OEM-recommended conditioning (allow to warm to room temperature or use manufacturer guidance) to help it seat properly.

Hose washer and plastic insert for inlet hose. To order separately: for washer use WPY013783, for strainer use WP22002960.

This replacement seal restores a tight barrier between mating parts in your appliance, helping maintain proper performance. It replaces a worn or deformed factory seal that can no longer hold a reliable fit due to age, heat, or chemical exposure.

• Creates a tight barrier between components to prevent leaks or air intrusion, as designed for the assembly
• Helps maintain correct pressure/flow and overall performance
• Common signs of failure: cracks, flattening, brittleness, or residue at the joint
• Helps address moisture seepage or performance loss at the sealed connection

• Disconnect power and, if applicable, turn off water supply before servicing
• Access the sealed joint; note the original seal's orientation
• Clean and dry mating surfaces thoroughly; install the new seal evenly and squarely
• Do not use sealants or lubricants unless specified by the manufacturer; test for leaks/fit before reassembly

The Seal is an OEM replacement part for Whirlpool dryers. It creates a tight seal between the dryer door and the drum, preventing heat and moisture from escaping during the drying process. It helps maintain the proper temperature inside the dryer, allowing your clothes to dry quickly and evenly.

Symptoms of a faulty door seal include:

• Heat escaping from around the dryer door
• Excessive moisture or lint buildup
• Extended drying times

A bad door seal can occur due to regular use, wear and tear, or accidental damage. If you notice issues such as heat escaping from around the dryer door, excessive moisture or lint buildup, or clothes taking longer to dry than usual, it may be time to replace the door seal.

This Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This door seal is the refrigerator door gasket that helps maintain a tight seal to keep cold air in and reduce energy loss. Replacing a worn or torn gasket helps the appliance cool efficiently and protect stored food. What it does

• Forms an airtight barrier around the refrigerator door to prevent warm air from entering
• Helps maintain consistent internal temperature and efficient operation
• Reduces frost buildup and cycling caused by a leaking seal
• Commonly shows symptoms like visible cracks, tears, flattening, or a door that won't close snugly

• One refrigerator door gasket

• Inspect the door frame and strike surfaces; clean mounting channel before installing the new gasket
• Warm the gasket slightly or use recommended installation tools to ease fitting into the channel
• Check alignment and closure after installation; replace if mounting clips or retainer are damaged
• Disconnect power only if required by your model and follow all safety precautions

This rubber door seal replaces a worn or damaged washer boot gasket to help keep water inside the tub and prevent leaks. It restores a tight, flexible seal around the door opening for reliable washing performance. What it does:

• Creates a watertight barrier between the wash tub and the door to prevent leaks
• Helps contain suds and water during fill and spin cycles
• Reduces odors and mold buildup by restoring a smooth, intact sealing surface
• Typical symptom: visible tears, deformation, or water pooling around the door

• One replacement door seal/gasket

• Disconnect power and turn off water supply before starting any repairs
• Inspect mounting lip and retaining band; replace any damaged clamps or retainers as needed
• Clean the sealing surfaces and allow to dry before installing the new seal