Maytag Range / Cooktop / Oven Parts

This electronic control board manages your oven's display, keypad inputs, and heating functions. Replacing a failed board can restore responsive controls, proper bake/broil operation, and reliable timing so your range or wall oven works as designed. What it does:

• Interprets keypad inputs and updates the clock/temperature display
• Controls bake and broil circuits via onboard relays
• Monitors the oven temperature sensor to regulate heat
• Runs cooking modes and timers

• 1 electronic control board assembly

• Disconnect power at the breaker before servicing; verify no power is present
• Handle the board by the edges and use ESD precautions
• Note/photograph wire locations; transfer any brackets or supports from the original board
• After installation, restore power and test bake/broil functions to confirm operation

This flame spreader sits between the burner base and cap to distribute gas evenly through the burner ports. Replacing a clogged or warped spreader restores reliable ignition and a steady, balanced flame for consistent cooking. What it does:

• Distributes gas to create an even, circular flame pattern
• Supports reliable ignition by positioning ports around the electrode
• Helps maintain proper heat output and flame stability
• Symptoms include uneven/weak flames, yellow flames, delayed ignition, or a burner that won't light

• One flame spreader

• Disconnect power and shut off gas; allow the cooktop to cool completely
• Remove grate and burner cap; lift off the old spreader (remove retaining screw if present)
• Align the new spreader over the orifice and igniter; seat fully and secure
• Do not clear ports with hard objects; use a soft brush and verify proper flame and ignition after reassembly

This door hinge restores smooth, controlled opening and a tight seal on the oven door. It supports the door's weight with spring tension so the door closes fully and stays positioned without slamming or sagging.

• Provides the spring-loaded pivot that controls oven door movement
• Helps ensure the door closes flush for a proper seal and heat retention
• Common symptoms: door won't close fully, drops or slams, won't stay at a set angle
• Reduces squeaks/binding and corrects uneven gaps around the door

• Disconnect power to the range or wall oven; shut off gas supply if applicable
• Remove and support the door to access hinges
• Springs are under high tension—use caution and proper locking method; wear gloves and eye protection
• After installation, verify door alignment and gasket contact all around

This burner cap sits on top of the gas burner head to shape the flame and shield it from spills. Replacing a damaged or missing cap restores proper flame pattern, reliable ignition, and even heating.

• Shapes and disperses the burner flame for even cooking and proper simmering
• Shields the burner head/orifices from spills, grease, and debris
• Must sit level and centered for consistent ignition and flame quality
• Replace if cracked, chipped, warped, missing, or if flames are uneven or yellow

• Allow the appliance to cool completely. Turn off gas supply and power before servicing.
• Lift off the old cap; clean and dry the burner head so the new cap seats properly.
• Center the new cap on the matching burner; it should sit flat with no rocking or gaps.
• Light the burner to verify an even, blue flame; realign the cap if ignition is delayed or the flame is uneven.

This window gasket fits between the appliance's window glass and the surrounding frame. It cushions the pane and helps seal gaps so the window stays secure, reduces rattles, and maintains proper performance around the viewing area. What it does:

• Seals the perimeter of the window glass to the door/frame
• Cushions the glass to reduce vibration and rattling noises
• Helps limit unwanted air/heat/steam leakage around the window area
• Common signs of wear: torn or flattened gasket, visible gaps, loose or shifting glass

• 1 window gasket

• Disconnect power and allow all surfaces to cool before starting
• Support the door and glass; wear cut-resistant gloves and eye protection
• Note the gasket's orientation; seat it evenly without stretching or twisting
• Reassemble and verify an even, continuous contact around the window

This replacement thermostat knob mounts on the control shaft to set cooking temperature. It restores a secure grip and clear pointer so you can choose settings reliably when the original knob is cracked, stripped, or missing. What it does:

• Attaches to the thermostat/control shaft to adjust temperature settings
• Provides a clear pointer and tactile grip for accurate selection
• Can help resolve issues like slipping, not engaging the stem, or worn/illegible markings
• Helps restore consistent temperature adjustment when the original knob is damaged or missing

• One thermostat control knob

• Turn the appliance off and allow surfaces to cool before servicing
• Pull the old knob straight off the shaft—do not pry against the control panel
• Align the new knob with the shaft orientation/indicator and press on until fully seated
• Verify the pointer aligns with the Off/temperature marks and turns smoothly through the range

This bake element restores primary heat to the lower oven cavity. Replacing a burned-out element helps bring back consistent temperatures and reliable baking performance.

• Provides radiant heat during bake cycles in the lower oven cavity
• Failure symptoms can include no heat in bake mode, very slow preheat, uneven baking, or a visible break/blister on the element
• Restores stable, even temperatures so recipes cook as intended
• Replaces an open or shorted element to return the oven to normal operation

• Disconnect power at the breaker before servicing.
• Remove oven racks and bottom panel to access the element; remove mounting screws.
• Carefully pull the element forward and disconnect the two wire terminals; do not let wires slip back into the cavity.
• Install the new element, reattach terminals and screws, restore power, and test bake.

The Element-Surf is an OEM part for Whirlpool electric ranges. The element-surface performs a role in safe, even heating.

Causes of a worn or damaged element-surface can include scratches, cracks or chips from cookware use over time. Surface level issues compromise effectiveness.

Symptoms of a damaged element-surface include:

• Uneven or slow heating between elements
• Exposure of electrical components below
• Food debris easily getting lodged in irregularities
• Loss of the glossy smooth appearance

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This burner cap sits on a sealed gas burner to shape the flame and protect the burner head. Replace to restore even heat and reliable ignition when the original is damaged, warped, or missing.

• Shapes and distributes the flame for even heating and better simmer control
• Shields burner ports from spills and debris to help prevent clogging
• Aids proper ignition and flame stability when correctly seated
• Common symptoms: uneven or yellow flames, sputtering, delayed ignition, continuous clicking, visible chips/warping

• Allow the cooktop/range to cool; shut off gas and power as needed
• Match the cap to the correct burner position for your model
• Lift off the old cap; clean the burner head/ports; set the new cap flat and centered
• Light and test; if flame is uneven or noisy, reseat and re-test

The broil element is the oven's upper heating element that delivers direct radiant heat for broiling and finishing foods. Replacing a failed element restores consistent top-side browning and proper broil performance.

• Provides high, direct heat from the top of the oven during the Broil cycle
• Restores broil function when the original element is open or damaged
• Common symptoms: no heat on Broil, weak/uneven top browning, element won't glow, visible breaks or blistering
• Matches the original design for proper fit and heat output on applicable models

• Disconnect power at the breaker or unplug the range; allow the oven to cool completely
• Remove oven racks to access the element
• Take out the element's mounting screws, gently pull the element forward, and transfer the wires one at a time to the new element
• Ensure terminals are fully seated and mounting screws are snug; restore power and test Broil

This oven door spring restores the door's counterbalance so it opens smoothly and closes firmly. Replacing a fatigued spring helps prevent heat loss and supports consistent baking by ensuring the door seals properly. What it does:

• Provides tension to counterbalance the oven door through the hinge mechanism
• Helps the door close fully against the gasket to retain heat
• Restores smooth, controlled opening and closing action
• Common symptoms of a worn spring: door drops or feels heavy, won't stay closed, heat escaping/uneven temperatures

• One oven door spring

• Disconnect electrical power; turn off gas supply to the range if applicable
• Springs and hinges are under tension—support the door/hinge and use caution
• Note spring hook positions/orientation before removal; reinstall in the same locations
• After replacement, verify the door closes fully and the seal is even

This surface burner spark electrode creates the electrical arc that lights the gas at your cooktop/range burner. Replace a cracked or fouled electrode to restore quick, reliable ignition on the affected burner and reduce repeated clicking.

• Generates the high-voltage spark that ignites surface-burner gas
• Promotes fast, consistent ignition and stable flame startup
• Common symptoms: burner won't light, lights intermittently, or sparks weakly at one burner while others work
• Visual clues: cracked porcelain insulator, bent tip, or heavy buildup on the electrode

• Disconnect power and shut off gas supply before servicing
• Remove grate, cap, and burner head to access the electrode
• Transfer mounting hardware from the old electrode
• Route and reconnect the lead securely; keep it away from heat and sharp edges, then test for proper spark before reassembly

Replace a failed surface heating element to restore reliable, even heat on your electric cooktop or range. This 3200-watt element helps get that cooking zone working properly again.

• Generates heat for the selected surface burner when turned on
• Works with the control to reach and maintain the set cooking temperature
• Useful when the old element shows visible breaks or burn marks

• Disconnect power at the breaker/fuse box and allow the cooktop to cool completely
• Access the element beneath the cooktop top panel per your model's procedure
• Label/photograph wire locations; transfer wires and any mounting hardware from the old element
• Handle the element and glass surface carefully to prevent damage

This Whirlpool touchpad and control panel is intended for use with wall ovens. The control panel and touchpad provide users with the ability to control the oven's functions. The touchpad can wear out through normal, everyday use over time. The panel itself, although made from stainless steel and very durable, can also begin to wear if not properly cleaned and maintained.Signs that the touchpad might need to be replaced include difficulty pressing the buttons and operating the oven. If the overlay on the display is difficult to read, or if the metal is corroding, it should also be replaced. Before replacing this part, first turn off the breaker to the oven. Then, remove the two screws at the top of the display and pull outward. Remove the control board from the inside and install it in the new panel, then install the panel.This is a genuine OEM part, sold individually. It fits Maytag wall ovens only.

Each piece is sold separately from the unit. This part is a Whirlpool oven control panel assembly. The control panel assembly and control board act as one unit to make up the central command center of the oven. The front-facing area contains the dials visible to the user, and the rear houses the actual circuit board. When a control panel assembly or the control board malfunction, the oven is essentially out of commission. In some cases, the malfunction may be gradual, with specific settings and functions going out one at a time. If burners begin to short out individually, or certain functions cannot be toggled on or off, it may be time for a replacement control board assembly.Installation of the part on compatible models is fairly simple. There is one screw on each side of the control panel assembly on the front of the oven. Remove these screws and the control panel should slide off with ease. There are two connecting wire harness components on either side of the control panel. Remove these connections and replace with the new control board, and pop it back into place before replacing the screws. This component can be used with Whirlpool or Maytag appliances. It is a genuine OEM product sourced directly from the manufacturer.

Replace a clogged or damaged rear burner with this surface burner head in black. It channels gas to the flame ports so the rear burner lights reliably and delivers a consistent, even flame for everyday cooking.

• Directs gas through precisely sized ports to form the rear burner flame pattern
• Interfaces with the spark igniter/electrode for dependable ignition
• Helps restore proper burner performance when ports are worn, corroded, or blocked
• Common symptoms: burner clicks but won't light, uneven or weak flame, yellow tipping, delayed ignition

• Shut off gas supply and disconnect power before servicing
• Remove grate and burner cap; take out mounting screws and lift the old burner head straight up over the igniter
• Align the new head over the orifice and igniter; secure with the existing screws
• Reassemble and test for proper ignition and flame on all burners