Maytag Range / Cooktop / Oven Parts

Replace a damaged or discolored oven handle with this white door handle. It restores a secure, comfortable grip and a clean look so you can open and close your range or wall oven door with confidence.

• Provides the handhold used to open and close the oven door
• Replaces cracked, broken, loose, or missing handles
• Helps restore safe handling and original appearance
• White finish to match compatible models

• Disconnect power at the breaker and allow the oven to cool completely
• Support the door/outer glass; remove inner door screws to access the handle mounts
• Transfer any end caps or hardware from the old handle, if applicable
• Tighten fasteners evenly; reassemble and check door operation

Replace a worn or missing surface-burner knob with this black infinite switch control knob. It restores smooth, accurate heat selection on your range or cooktop when the original knob is cracked, stripped, loose, or missing. What it does:

• Interfaces with the surface burner's infinite switch to select OFF through Low–High heat levels
• Restores positive, secure control of the burner
• Typical symptoms: knob cracked, spins freely, falls off, or can't adjust temperature
• Helps ensure consistent response when turning the burner on/off and setting heat

• Disconnect power and allow the cooking surface to cool completely
• Pull the old knob straight off the switch shaft
• Align the new knob with the shaft and press on until fully seated; do not force
• Rotate through all settings to confirm smooth operation

This orifice spud meters gas to a burner on your range or cooktop, setting proper flame size for efficient, even heating. Replacing a damaged or incorrect spud restores consistent burner performance and flame quality.

• Meters gas flow through the burner orifice to control flame height and shape
• Supports efficient combustion and consistent heat output
• Common fix for flames that are too high/low, yellow/sooty, or uneven
• Used when setting up or converting a model for the specified fuel type (LP or natural), per the position of each burner

• Shut off the gas supply and disconnect electrical power before servicing
• Remove the burner cap and head to access the spud; lift the cooktop or open the range top if required
• Remove/install with a properly sized wrench; do not overtighten. Apply thread sealant only if specified by the manufacturer
• Match each spud to the correct burner and fuel type per your model documentation; after reassembly, restore gas and leak-test with a soapy-water solution

This is a dual radiant surface element for use with certain range models. The surface element supplies heat to the cooking area on the range's surface. If the element is not functioning correctly, the owner will not be able to use the range because it won't heat up.The dual radiant surface element is long-lasting, but this does not mean it will last forever. It could still need to be replaced if it wears out or is damaged. Shut off the circuit breaker to the range or unplug it before starting this replacement.The dual radiant surface element is sold individually. It is compatible with select models from Whirlpool, Maytag, and KitchenAid. This is a genuine OEM replacement part sourced from the manufacturer.

This surface burner infinite switch is the behind-the-knob control for an electric cooktop or range. It regulates power to a single surface element so you can dial in and maintain the heat you need.

• Regulates on/off power cycling to a coil or radiant surface element for variable heat control
• Helps address issues such as a burner not heating, only heating on high, not turning off, or fluctuating temperature
• Installs behind the control panel; connects with spade terminals to line, load, and element leads
• Single-surface-element control for one burner position

• Disconnect power before servicing; this component carries high voltage
• Note wire positions or transfer one wire at a time from the old switch to the new switch
• Secure the switch to the control panel and align the shaft with the control knob
• Reassemble and verify smooth low-to-high burner operation

This grill element is the radiant heating coil used for the appliance's grill/broil function. Replacing a failed element restores strong, even radiant heat for searing, browning, and finishing as designed.

• Provides direct radiant heat for the grill/broil cycle
• Cycles under control to maintain target temperature
• Common fix for no broil/grill heat or uneven top browning
• Visible damage such as blisters, breaks, or arcing points indicates replacement is needed

• Disconnect power at the breaker or unplug before servicing; allow the unit to cool
• Access the element per your model; remove mounting screws and carefully lower/slide it out
• Disconnect the wire terminals; support wires so they don't retract into the cavity
• Attach wires to the new element, secure with original hardware, and avoid bending the coil

This gas valve controls the flow of gas to a burner, enabling safe ignition and precise flame adjustment. Replacing a worn valve restores smooth knob operation and consistent flame performance on your gas cooking appliance.

• Opens and closes to start/stop gas flow to a specific burner
• Works with the control knob to modulate flame size
• Helpful when a burner won't light despite spark/ignition present
• Can address issues like inconsistent flame or a knob that's hard to turn

• Disconnect power and shut off the gas supply before servicing
• Match the orientation and connections to the original valve
• Use an approved gas-rated thread sealant on threaded fittings
• After installation, check all joints for leaks with a soap-and-water solution

This is the replacement cooktop, also called the main top, for sealed-burner gas units. It forms the cooking surface around the burners to contain spills, restore appearance, and keep grates and burner parts seated securely for safe, even heating.

• Forms the main cooking surface and supports burner heads/caps and grates
• Sealed-burner design helps keep spills on top, protecting components below
• Maintains proper burner alignment and flame pattern
• Common symptoms: cracks, chips, dents, rust, or warping; wobbly grates or gaps around burner openings

• Disconnect power and shut off the gas supply before servicing
• Remove grates, burner caps, and the screws securing burner heads; lift off the old top
• Transfer/reconnect igniters and wiring as equipped; avoid pinching wires during reassembly
• Restore gas and power, verify ignition on all burners, and check for leaks

Color: Black. Used on some dryers and broiler drawers.

Replace a failed range clock/control with this factory Clock and Overlay Kit. It restores a readable display and responsive keypad so you can set time, temperature, and cooking modes confidently on compatible ranges and wall ovens.

• Controls oven functions by processing keypad input, driving the display, and switching bake/broil circuits via internal relays
• Common failure symptoms include a blank or erratic display
• Keypad buttons may be unresponsive or intermittent
• Oven may not start or heat due to the control not sending power
• Control-related error messages or beeping can appear

• Disconnect power at the breaker before servicing; verify no voltage is present
• Handle the control with ESD care; avoid touching circuitry and connectors
• Move wires one at a time from old to new control; take photos for reference
• Align and apply the overlay carefully to a clean surface before pressing into place

This oven igniter is the glow-bar that lights the gas for the bake or broil burner. Replacing a weak or failed igniter restores dependable ignition and consistent oven heat, solving no-heat and long preheat complaints.

• Heats to ignite the gas burner in the oven cavity
• Draws the proper current to open the oven safety valve
• Common symptoms: oven won't heat, igniter glows but no flame, delayed or intermittent ignition, extended preheat times
• Restores reliable burner lighting for baking or broiling

• Disconnect power and shut off gas supply before servicing; allow the oven to cool
• Handle the igniter by the insulated base; avoid touching the fragile element
• Mount using the correct bracket and position the tip near the burner, as on the original
• Restore power and gas, then test for prompt, steady ignition

For Use With LP

This surface burner ignitor switch mounts on the gas valve and signals the spark module when you turn the knob to Lite. Replacing a faulty switch restores reliable clicking and ignition on the affected burner. What it does:

• Closes the circuit to send power to the spark module when a knob is turned
• Helps produce a steady spark at the electrode for quick burner lighting
• Common symptoms it may address: no spark on one burner, constant clicking with knobs off, or intermittent sparking
• Used on gas cooktops/ranges that employ one spark switch per burner valve

• 1 ignitor switch

• Disconnect power and shut off gas before servicing
• Remove the knob and access the control area to reach the switch on the valve stem
• Note wire positions; transfer wires to the new switch and align it correctly on the valve
• Reassemble, restore power/gas, and test for proper spark operation

By Maytag/Magic Chef. Set of 4 chrome square drip pans for gas ranges / cooktops. Fits many brands, including Maytag, Magic Chef, Admiral, Crosley, Norge, Jenn Air and others. Matching set of grates: 1430291.

This gas surface burner valve regulates fuel flow to a cooktop or range burner for safe ignition and smooth flame control. Replace a worn or sticking valve to restore consistent flame adjustment and reliable knob operation.

• Regulates gas to the surface burner; opens/closes as the control knob is turned
• Helps resolve no-flame or no-ignition conditions when sparking is present
• Restores proper flame adjustment from low simmer to full boil
• Addresses stiff, seized, or inconsistent valve action at the knob

• Disconnect electrical power and shut off the gas supply before servicing
• Remove the knob and access the manifold to detach the old valve; note tubing and orientation
• Transfer any mounting clip or fittings from the original valve if required by your model
• After reassembly, check all connections with an approved leak-detection solution and verify burner operation

Radiant surface element for smooth-top electric ranges that restores consistent heat to a 6-inch burner so cookware can reach and maintain proper cooking temperatures. Ideal when a burner fails to heat evenly or stops working. What it does:

• Heats cookware via the cooktop's 6-inch radiant zone for boiling, simmering, and frying.
• Replaces a worn or damaged smooth-top element to restore normal burner performance.
• Common symptoms: burner won't heat, only part of the burner heats, or the burner cycles instead of holding steady heat.
• Designed for glass/ceramic cooktops—handle carefully to avoid damage.

• Disconnect power to the range before beginning any repair to prevent electrical shock.
• Allow the cooktop to fully cool; handle the glass element carefully to avoid chipping or cracking.
• Seat electrical connectors securely and align the element in the cooktop opening; do not force.