Maytag Range Wire, Harness, Power Cord

This wire harness routes power and signals between appliance controls and electrical components to restore reliable operation. Replaces a damaged, frayed, or burnt harness to help eliminate intermittent or lost power to components. What it does:

• Carries electrical power and control signals between the control board and motors, switches, sensors, or heating elements
• Restores consistent electrical connections when original wiring is damaged, corroded, or pinched
• Addresses symptoms such as components not powering on, intermittent operation, blown fuses, or visible burn/damage at wiring
• Prevents shorting and arcing caused by exposed or broken conductors when replaced promptly

• One wire harness as pictured and specified by the manufacturer

• Disconnect power at the breaker or unplug the appliance before inspecting or replacing the harness
• Match connector shapes and pin counts; route harness clear of sharp edges, heat sources, and moving parts
• Use only the exact replacement harness to maintain proper connector fit and circuit protection
• If you see burned connectors, melted insulation, or a repeatedly tripped breaker, inspect related components and replace damaged parts as needed

This wire harness routes electrical power and signals between components to restore proper appliance operation. It replaces damaged or worn wiring to eliminate intermittent connections and reduce the risk of shorts. What it does:

• Connects motors, switches, sensors, and heaters so components receive power and signals
• Restores reliable electrical paths when original wiring is frayed, burnt, or broken
• Helps stop intermittent operation, failure-to-start symptoms, or components losing power
• Reduces risk of arcing or short circuits caused by damaged insulation or loose terminals

• Always disconnect power (unplug or shut off breaker) before inspecting or replacing wiring
• Compare connectors and wire colors to the original harness to ensure correct fit before installing
• Route and secure wiring away from heat and moving parts; avoid pinching or sharp edges
• If you see melting, burning, or damaged terminals on mating parts, replace or repair those components too

This wire harness connects key components so your appliance controls and sensors communicate reliably. Replaces a damaged or frayed harness to restore normal electrical connections and help resolve intermittent power or control issues. What it does:

• Routes power and signal connections between the control board, switches, and sensors
• Restores missing or intermittent electrical continuity caused by broken or burned wires
• Helps stop erratic operation, control failures, or no-power conditions linked to damaged wiring
• Matches OEM connector and terminal locations for a direct replacement

• Disconnect power at the breaker or unplug the appliance before starting any work
• Handle connectors gently; match keyed plugs and secure all wire routing away from moving parts and sharp edges
• If terminals are corroded or connectors are damaged, replace connectors

This wire harness routes power and signals between the appliance's electrical components to restore reliable operation and proper control functionality. It replaces a damaged or worn harness to fix intermittent power, control failures, or burnt connectors. What it does:

• Connects control board, switches, motors and other electrical components so they communicate and receive power
• Restores lost or intermittent power caused by broken or frayed wires
• Resolves control or function failures when caused by damaged wiring or connectors
• Prevents arcing and poor connections from worn terminals or insulation

• Disconnect power (unplug appliance or switch off breaker) before any service
• Match connectors and routing to the original harness; secure using existing clips and holders
• Inspect mating connectors and boards for heat damage before installing the new harness

This replacement wire provides a direct electrical connection between appliance components to restore proper function and safe operation. Use it to replace a damaged or frayed lead that's causing intermittent or lost connectivity. What it does

• Carries electrical current between terminals or components to enable operation
• Restores a secure connection when the original lead is cracked, cut, or corroded
• Can stop intermittent power, no-starts, or erratic behavior caused by a damaged lead
• Helps prevent arcing or shorts when a worn wire is replaced

• One replacement wire as shown

• Disconnect power to the appliance before checking or replacing wiring
• Verify terminal orientation and secure connections; use correct connectors and insulation
• Replace only like-for-like wire gauge and routing to maintain safety and performance
• If pins, splices, or connectors are damaged, replace or repair them per OEM guidance