Mcculloch Carburetor

This carburetor assembly can be used as a replacement part for the small engine of a string trimmer, a chainsaw, or an edger. The carburetor assembly contains a replacement carburetor and the components required to facilitate the replacement and installation of the carburetor. The purpose of the carburetor is to create a mixture of the fuel and air that the engine takes in and channel it through the network of valves to the spark plugs, which ignite and power up the engine.A carburetor might have to be replaced if it is damaged to the point of exhibiting the following symptoms, among others: black smoke pluming from the exhaust, reduced fuel economy, misfires and false starts of the engine, and oil leakages stemming directly from the carburetor. If this is the case, this carburetor assembly should be ordered as a replacement. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This is an OEM part sourced directly from the manufacturer, MTD. It is sold individually. This carburetor assembly is compatible with the following brands: MTD, Troy-Bilt, Ryobi, and Yard Man.

This is a replacement carburetor for Husqvarna string trimmers and is also used on some Craftsman models. It consists of an aluminum body with a bright blue choke and cherry red primer bulb. Engines rely on a mixture of fuel and air for proper operation. In a small engine, the fuel and air mix inside the carburetor. This is achieved with a series of small channels, which release a fine mist of fuel into a vortex of air. When one of these channels gets clogged, it can negatively impact engine performance. Carburetors can often be cleaned with a commercial carburetor cleaning spray, but this is sometimes not sufficient to clean a badly clogged carburetor. In this case, other measures such as hypersonic cleaners can often be effective, but they’re not always worth the cost. The alternative is replacing the entire carburetor, which can be done using this kit. This is an OEM part sourced directly from the manufacturer, and it is sold individually. A heat shield is also included with the kit.

The chainsaw carburetor mixes air and gas before this mixture makes its way to the engine. If this is not working correctly, the engine receives a less efficient gas supply or no gas supply at all. If your chainsaw has a full tank of gas but will not start or stops just after starting, the carburetor may need to be replaced. While carburetors can be cleaned to get them working again, they often need to be replaced if they have become too clogged. Depending on what you can reuse from your old carburetor, you may need to order new gaskets as well to ensure an airtight seal. A screwdriver, a nut driver, and a socket wrench set may be needed to complete this repair. This chainsaw carburetor is sold individually from other parts, but it does include the primer bulb. It is compatible with Craftsman and Poulan chainsaws. This chainsaw carburetor is a genuine OEM part.

This high quality choke lever is used on string trimmers and edgers from multiple manufacturers. The plastic choke lever actuates the choke valve which creates a limit to the amount of air that can enter the engine when the equipment is cold started. If the choke lever has been damaged or is broken, it may create problems with starting the tool. If this is the case, the choke lever will need to be replaced.This is a simple replacement project that requires only a screwdriver and a pair of work gloves. Before starting, make sure the tool is turned off and the spark plug wire has been removed. Place the tool on a flat surface and take out the choke lever. The broken choke lever can be removed using the screwdriver. The new replacement choke lever can be installed before tightening the screws and using the equipment again.This is a genuine OEM replacement part that is sourced directly from the manufacturer. It is sold as an individual part. The choke lever is made for use with edgers and string trimmers manufactured by Craftsman, Husqvarna, and Poulan.

Blowers are often designed with gas-powered engines. When a blower has adequate fuel, but the engine does not start, it could be a problem with the carburetor. This is the part that mixes air and fuel to send into the engine. If an engine starts and dies or fails to start at all, the carburetor may need replacement. This replacement for a blower carburetor works with Craftsman and Poulan blowers, and is compatible with a long list of models. This is an OEM replacement part that features a metal body and which incorporates the rubber primer bulb necessary to begin the starting process. It ships individually and is will require pliers and a screwdriver to make the repair.

This throttle linkage is a genuine Husqvarna part, sold individually. This throttle linkage can be used as a replacement part in a leaf blower. The purpose of the throttle linkage in a leaf blower is to affix the throttle control to the carburetor so that the carburetor and throttle can work in unison to provide power to the engine and control the speed of the appliance as it is propelled forward across a variety of surfaces.The throttle linkage in a leaf blower might need to be replaced if the throttle linkage has permanently detached from its stable position within the throttle controls of the appliance or if the throttle linkage has suffered irreparable damage. If the throttle linkage is not serving its function and cannot be repaired, the throttle linkage should be removed and replaced by this genuine OEM replacement part.Sourced directly from the manufacturer, this component is a genuine replacement part that is sold individually. This throttle linkage is compatible with the following outdoor appliance brands: Husqvarna, Craftsman, Weed Eater, Poulan, and Poulan Pro.

The genuine replacement primer bulb covers the primer base and plunger on specific leaf blower models. Before starting the leaf blower, the primer is pushed to allow fuel to flow into the carburetor to assist in a smooth engine start. It can also make starting the equipment easier after it has been sitting for a period of time. The bulb is made of plastic and exposed to the elements, so over time it can become cracked, worn, or even completely lost. Without it, the engine cannot be properly primed before operating and therefore will not run as well. Replacing the bulb with a genuine OEM model like this should be done as soon as possible. This OEM primer bulb is manufactured by Husqvarna and can be used for a variety of leaf blowers that are manufactured by the brand. This model is also compatible with Poulan, Craftsman, and Weed Eater products. The bulb is made of durable rubber and may require a screwdriver for replacement to assist in fitting the bulb into place. This unit is sold individually and does not include the primer base assembly or any hardware.

This OEM carburetor is designed as a replacement for compatible leaf blowers. The carburetor takes in air and fuel and mixing them together before sending the mixture onto the engine to power the machine. The air comes in through an air filter to remove any impurities and then it passes into a smaller inner chamber, where fuel is injected through small holes in the chamber after also being filtered. Then, the two mix and are passed into the engine through an adjustable butterfly valve. If the engine isn't performing well or will start but won't stay running, the carburetor could be in need of replacement. It’s usually easier to replace the entire assembly than individual parts, and this genuine OEM part can provide the solution for machines it fits. This carburetor replacement is specifically designed to be compatible with select Craftsman, Poulan, and Husqvarna leaf blower engines. The carburetor does not include any gaskets or hardware required for replacement, so those will need to be purchased separately if they are required. Be sure that the engine is completely cool before beginning repairs and wear gloves for hand protection whenever performing engine work on any machines.