Parts for Kenmore Elite 79551829412: Mechanical Compartment Parts

This is a genuine replacement screw used to secure appliance panels and components. It restores proper fastening so panels and assemblies stay aligned and operate safely. What it does:

• Fastens panels, brackets, and small assemblies to maintain structural integrity
• Replaces missing or stripped screws that cause rattling or loose parts
• Helps stop vibration-related noise when used in its original mounting locations
• Matches the OEM fit to ensure proper alignment and clearance

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or component damage
• Disconnect power to the appliance before working on electrical components
• Replace all matching fasteners for even fit

The Drain Pipe Assembly is an OEM replacement part for LG refrigerators. It is a plastic tubing system that collects and removes liquid condensation from evaporator coils. Proper drainage is crucial to minimizing frost buildup and ensuring optimal cooling of food storage areas. 

Symptoms of a bad drain pipe assembly include:

• Excessive frost or ice accumulation inside the refrigerator
• Puddling or leaks detected near evaporator housing
• Slow draining allowing water to pool versus emptying fully
• Cracks or breaks in the tubing prevent complete fluid removal

Causes are typically mineral sediment clogging drainage paths or deteriorating plastic from constant use. This OEM LG replacement pipe restores reliable condensate removal to maintain peak efficiency.

This OEM LG part is also compatible with Sears/Kenmore. 

This adjustable leveling leg assembly supports and stabilizes the refrigerator. Replacing a worn or damaged leg restores proper leveling, reduces vibration and noise, and helps doors align and seal correctly.

• Provides height adjustment at the cabinet corner to level the appliance on uneven floors
• Helps prevent rocking, rattling, and excessive vibration
• Promotes proper door alignment and gasket sealing
• Replace if the foot is broken, missing, bent, or the threads are stripped and won't hold adjustment

• Disconnect power and turn off the water supply before servicing
• Protect the floor; with a helper, carefully tip and support the refrigerator
• Unscrew the old leg; hand-thread the new leg, then fine-tune height with a wrench until level
• Ensure both front legs share the load evenly and recheck door operation

The Lever Dispenser is an OEM part for LG refrigerators. It is the control mechanism responsible for dispensing crushed ice and water through the refrigerator door without opening it. The lever and dispensing components are designed to withstand frequent use while retaining smooth, reliable operation. 

Causes of a bad lever dispenser can include worn parts inhibiting proper dispensing movement, cracks or damage reducing structural integrity, or mineral buildup affecting functionality over time.

Symptoms of a bad lever dispenser include:

• Difficulty or inability to dispense ice and water
• Leaks or drips around the dispenser area 
• Loose, rattling, or unresponsive lever action  
• The dispenser not activating or emptying the reservoir

This OEM LG part is also compatible with dispenser models featured on Kenmore side-by-side refrigerators.

This dispenser lever holder is the mounting bracket behind the refrigerator's dispenser paddle. It supports and aligns the lever and switch so water or ice dispenses reliably when the paddle is pressed.

• Holds and guides the dispenser lever and actuator switch inside the dispenser housing
• Provides a secure pivot point for smooth paddle movement
• Helps ensure consistent activation of water and ice dispensing
• Damage can cause a loose or stuck paddle, intermittent dispensing, or no dispense

• Disconnect power and shut off the water supply before servicing
• Remove the dispenser panel/escutcheon to access the lever assembly; note part orientation
• Transfer the lever, switch, and return spring to the new holder and secure with the original fasteners
• Restore power/water and test dispensing before reinstalling trim

The Ice Door Lever Spring is an OEM component compatible with LG refrigerators. It is part of the mechanism that opens and closes the ice door on LG French door refrigerators. Over time, springs can lose resiliency or become misaligned.

Causes may be extensive usage over years or damage like kinking that compromises spring function.

Symptoms of a bad ice door lever spring include:

• The ice door not latching fully when closed
• Difficulty opening or poor balance while moving the door
• The lever rubbing or catching instead of moving smoothly

This OEM LG part is also compatible with Sears/Kenmore side-by-side refrigerators.

This insulated duct assembly replaces a worn or damaged dryer exhaust duct to help contain heat and airflow for more efficient drying and reduced cabinet heat. Designed to restore proper venting and reduce noise from a failing duct. What it does:

• Channels exhaust air from the appliance while the insulation helps limit heat transfer to surrounding panels
• Helps maintain dryer efficiency by preserving exhaust airflow
• Reduces rattling or vibration caused by damaged or loose duct sections
• Helps prevent excessive cabinet heating and reduce felt heat near the appliance

• Disconnect power (and gas, if applicable) before beginning any repair
• Wear gloves to protect hands from sharp sheet-metal edges
• Ensure the assembly fits securely and clamps or fasteners are tightened to prevent leaks

This is an ice bucket assembly that is made to be used on refrigerator and freezer units. The purpose of this part is to store ice that has already been made. This makes it available for dispensing. This assembly includes the auger that rotates to move the ice cubes into the dispenser chute.Over time, the ice bucket assembly could become cracked or broken. This is due to normal wear and tear or simply being exposed to cold temperatures for so long. Since the auger is attached to it, the entire assembly will need to be replaced if the auger has stopped working correctly. Store any foods that may deteriorate in a temperature safe location before replacing this part.This part is sold individually. It is compatible with refrigerator and freezer units that are manufactured by Kenmore Elite. It is sourced straight from the manufacturer as a genuine OEM replacement part.

This drawer tray is the replacement interior tray that supports and organizes items inside the refrigerator drawer, restoring smooth storage and preventing items from sliding or contacting drawer components. What it does

• Provides a stable, flat surface inside a refrigerator drawer for food storage and organization.
• Supports produce and deli items so contents sit evenly and the drawer closes properly.
• Replaces cracked, warped, or damaged trays that can cause items to tilt or catch during drawer use.
• Helps maintain interior cleanliness by providing an easy-to-remove surface for wiping spills.

• One drawer tray (single replacement part as sold)

• Remove food and empty the drawer before replacing the tray.
• Lift the drawer out according to the refrigerator manual, replace the tray, then slide the drawer back in.
• Handle with care to avoid chipping edges; use gloves if needed.

This Drawer Tray Assembly replaces a damaged or worn crisper/produce drawer to restore proper storage and containment for fresh foods. It provides a stable, easy-to-clean surface and restores full drawer function in compatible refrigerators. What it does:

• Replaces a cracked, warped, or broken crisper/produce drawer to prevent spills and hold fruits and vegetables
• Restores smooth sliding and proper seating so the drawer opens and closes reliably
• Helps contain moisture and keep produce organized for normal refrigeration use
• Fits into the existing drawer tracks and uses the refrigerator's original mounting/location

• One drawer tray assembly

• Remove all food and empty the old drawer before installation
• Slide the old drawer out on its tracks and lift to disengage, then set the new tray into the tracks and verify proper seating
• No special tools typically required; inspect tracks and rollers for damage and clean before installing
• Disconnect power only if working near electrical components; otherwise follow standard appliance safety and use gloves to avoid sharp edges

This small stopper fits inside the handle assembly to limit travel and keep the handle properly seated. Replacing a worn or missing stopper restores a solid, secure feel when opening and closing your appliance.

• Provides a positive stop for handle movement
• Helps keep the handle aligned and seated against its mounts
• Replaces a cracked, deformed, or missing stopper
• Common signs: handle feels loose or wobbly, over-rotates, or shifts/clicks during use

• Unplug the appliance before servicing to prevent injury
• Support the handle and protect the finish while removing fasteners
• Note the original stopper's orientation and install the new one the same way
• Tighten fasteners evenly; do not overtighten to avoid damaging plastic or finishes

The Refrigerator Set Screw is an OEM part for LG refrigerators. This small but crucial component is used to secure various parts of the refrigerator, ensuring stability and proper alignment of the internal components. This set screw is sold individually.

Causes of a bad set screw can include stripping due to over-tightening, corrosion from moisture exposure, or wear and tear over time. A loose or missing set screw can lead to instability and misalignment of the refrigerator parts, potentially causing operational issues.

Symptoms of a bad refrigerator set screw include:

• Loose or wobbly internal components
• Doors not closing properly or misaligned
• Unusual noises from inside the refrigerator
• Parts becoming detached or misaligned

This OEM LG part is also compatible with Sears/Kenmore models.

This door basket is a molded refrigerator door bin that holds bottles, condiments and small items securely on the door shelf. It restores sealed storage and keeps door contents organized and easy to access. What it does

• Replaces a cracked, broken or missing refrigerator door bin to stop items from falling out
• Supports bottles, jars and containers on the inner door for organized storage
• Secures into door rail slots and provides a stable shelf surface
• Restores proper fit and appearance to the refrigerator door interior

• One door basket

• Remove all contents from the door and work with the door closed for safety
• Align the bin with the door rail slots, tilt and snap into place until fully seated
• No tools required for typical snap-in installations; use gentle pressure to avoid damage
• Inspect door rails for damage and replace rails if the bin does not seat correctly

This door basket is a replacement fridge door bin designed to restore storage on the refrigerator door and keep bottles, jars and small items secure. It replaces a worn, cracked or broken door bin so the door holds items safely again. What it does:

• Provides secure storage on the refrigerator door for bottles, jars and other small containers
• Replaces cracked, split or damaged door bin that no longer supports items
• Restores proper alignment and retention of items on the door shelf
• Helps prevent spills and shifting during normal door use

• One door basket

• Typically snaps into the door track or mounting clips; no special tools required for many installs
• Remove contents and empty shelves before removing the old basket
• Handle gently to avoid damaging door trim or clips; replace any broken clips if present
• Always unplug the appliance or disconnect power before working on internal components

This dairy bucket is the removable door bin that holds butter, cheese and small dairy items for easy access and organization. It restores a broken or missing door storage bin so food stays contained and accessible. What it does:

• Provides a dedicated, shallow storage area for butter, cheese and other small items on the refrigerator door
• Replaces cracked, broken or missing door bins that no longer stay secured or leak onto lower shelves
• Keeps dairy items contained to prevent spills and improve door organization
• Fits into the door bin track and snaps into place to hold lightweight items

• One dairy bucket

• Removes and installs by lifting or unhooking the old bin from the door rails and snapping the replacement into the same position
• Use gentle pressure to seat the bin; do not force or wedge to avoid damaging the door rail
• Clean with mild soap and water before first use and after spills; avoid abrasive cleaners
• Handle carefully to avoid chipping or cracking the plastic

This replacement door basket restores the removable basket that mounts to the appliance door, letting you load and secure items for washing or storage. It replaces a worn, cracked, or broken door-mounted basket to help restore normal use. What it does

• Replaces a damaged or cracked door-mounted basket used to hold items on the appliance door.
• Helps stop items from falling or shifting during normal use when the basket is mounted to the door.
• Commonly replaced when the basket shows visible damage, breaks, or no longer secures items safely.

• One door basket

• Intended for users comfortable with basic disassembly of the appliance door;
• Power off and unplug the appliance (or disconnect power) before beginning any repair.
• Handle plastic components gently to avoid additional cracking; use proper fasteners and alignment when reinstalling.
• If clips or screws are missing or damaged, replace them with OEM-specified hardware to ensure a secure fit.

The Door Stopper Assembly is an OEM component specifically designed for LG refrigerators. It secures the fridge door in fully closed and aligned positions. 

The stopper assembly utilizes a pneumatic cylinder and integrated mounts to softly cushion door movement. This allows for smooth closing with an audible click to confirm proper sealing.

Causes of a bad stopper assembly can include cracked or leaking air cylinders after years of use. Loose or sheared mounting hardware may also cause improper alignment and restricted closure.

Symptoms of a bad door stopper assembly include: 

• Gaps forming around the door seal when closed
• Doors difficult to latch fully or align correctly  
• Premature cooling loss from unsealed openings

Replacing this LG part restores a snug, confirmed door shut. The OEM stopper components ensure dependable closing effort for efficient operation. This replacement is compatible with some Kenmore models as well.

This upper hinge assembly supports the refrigerator door at the top and acts as the pivot point for smooth opening and closing. Replacing a worn hinge restores proper alignment and helps the door seal and close consistently.

• Supports and pivots the door at the top hinge point
• Maintains door alignment with the cabinet and gasket
• Helps ensure complete closure and proper sealing
• A worn hinge may cause door sagging, rubbing, popping/creaking noises
• Misalignment may lead to air leaks, frost, or temperature fluctuations

• Disconnect power and, if applicable, shut off the water supply.
• Remove the hinge cover, support the door, and note shim/bushing positions.
• Remove hinge screws, lift the door off, transfer any spacers/bushings, and install the new hinge.
• Align the door and verify gasket contact all around before restoring power.

This hinge lever mounts on the refrigerator door hinge to guide door movement and closure, helping the door seal properly. Replacing a worn or broken lever restores smooth operation and consistent sealing.

• Guides hinge motion so the door opens and closes smoothly
• Helps maintain door alignment for a reliable gasket seal
• Replace if the lever is visibly cracked, worn, or deformed

• Disconnect power and support the door to prevent injury or damage
• Remove the hinge cover and fasteners; note the lever's orientation before removal
• Install the new lever in the same position and reassemble the hinge components
• Adjust hinge per model procedures if needed

This replacement nut is a simple fastener used to secure internal components and panels. It restores proper attachment where a loose or missing nut causes vibration, noise, or parts to shift. What it does:

• Secures components, brackets, or panels in place to maintain appliance stability
• Prevents parts from loosening during operation, reducing rattles and vibration
• A missing or damaged nut can allow movement that leads to noise or improper alignment
• Use as a direct hardware replacement when the original nut is lost or worn

• Disconnect power (and water, if applicable) before accessing internal parts
• Start threads by hand to avoid cross-threading; tighten with the appropriate wrench or socket
• Replace if threads are stripped or the nut is damaged
• Refer to the parts diagram for the correct mounting location

The Lower Hinge Assembly is an OEM part for LG refrigerators. It is responsible for supporting the refrigerator door and allowing it to open and close smoothly. The hinge assembly ensures the door stays aligned and securely in place, preventing cold air from escaping and maintaining the efficiency of the appliance.

You should replace the lower hinge assembly if it becomes faulty. Causes of a bad lower hinge assembly can include wear and tear over time, excessive force or weight on the door, or damage from accidental impacts.

Symptoms of a bad lower hinge assembly include:

• Difficulty in opening or closing the door
• Door not sealing properly
• Squeaking or grinding noises when the door moves
• Door misalignment

This OEM LG part is also compatible with Sears/Kenmore models.

Note: Evaporator with Defrost Heater

This damper cushions and isolates the refrigerator compressor to reduce vibration and noise for smoother operation. It helps maintain stable compressor mounting and prevents metal-to-metal contact that can cause wear or rattling. What it does:

• Absorbs compressor vibrations to reduce noise and movement
• Helps protect the compressor housing and mounting points from shock
• Can reduce rattling or knocking sounds originating near the compressor area
• Supports proper alignment of the compressor assembly during operation

• One compressor damper (mounting isolator)

• Turn off power at the breaker and unplug the appliance before servicing
• Inspect mounting area and hardware; replace any damaged fasteners before installing the damper
• Position the damper on the compressor mount as shown in the service manual and secure per OEM guidance

This small stopper installs in the refrigerator to limit the travel of a moving component and keep it securely in place. Replacing a broken or missing stopper prevents over-extension and helps maintain smooth, aligned operation.

• Limits the range of motion for a door, bin, or drawer to prevent over-opening or accidental removal
• Helps keep interior components aligned and operating smoothly
• Replace if cracked, missing, or deformed
• Common symptoms: drawer or bin slides out too far, door swings past normal range, or a broken plastic stop is found

• Disconnect power before servicing; remove or support the affected bin/drawer/door
• Note the old stopper's orientation and location before removal
• Transfer and reuse any original screws or clips if applicable
• Snap or fasten the new stopper in place and test for smooth movement

A replacement base assembly that secures and isolates the refrigerator compressor to reduce vibration and help maintain proper alignment. Restores stable compressor mounting for quieter, more reliable operation. What it does:

• Supports and anchors the compressor to the appliance chassis to maintain correct positioning
• Absorbs and dampens compressor vibration to reduce noise and wear
• Helps prevent compressor movement that can stress refrigerant lines and mounts
• Restores proper fit and alignment after damage or corrosion of the original base

• Mounting requires accessing the compressor area—disconnect power and fully discharge any stored energy before starting
• Follow OEM service manual for removal/installation sequence and torque values where specified
• Inspect surrounding mounts, fasteners, and refrigerant lines for damage during replacement

The Drier Assembly is an OEM part for LG refrigerators. This part is responsible for removing moisture and contaminants from the refrigerant. This ensures that the refrigerant circulates effectively and efficiently, preventing damage to other components and maintaining the refrigerator's cooling performance.

Causes of a bad Drier Assembly can include contamination from moisture entering the refrigerant lines, blockages from debris or particulates, and general wear and tear over time that reduces its effectiveness.

Symptoms of a bad Drier Assembly include:

• Reduced cooling efficiency or warm refrigerator temperatures
• Unusual noises from the refrigeration system
• The compressor running continuously or cycling frequently
• Frost buildup on the evaporator coils due to improper refrigerant flow

This OEM LG part is also compatible with Sears/Kenmore models.

This fan assembly is the rotating blower that moves air through the appliance to support drying, venting, and internal cooling. Replacing a worn fan restores proper airflow and reduces noise or overheating risks. What it does

• Spins the blower wheel to circulate air for drying, venting, or cooling functions.
• Restores airflow when the appliance has weak or no air movement.
• Reduces abnormal rattling, grinding, or humming caused by a damaged motor or wheel.
• Helps prevent overheating by maintaining adequate internal ventilation.

• One fan assembly.

• Disconnect power before starting any repair.
• Access may require removing outer panels or interior trim; keep fasteners organized.
• Handle wiring connectors and harnesses carefully; match connector positions during reassembly.
• Test operation after installation and reassemble panels securely before returning the appliance to service.

This grille assembly covers and protects the refrigerator fan while helping direct airflow for proper cooling. Replacing a damaged or cracked grille restores protection and helps maintain efficient air circulation around the fan area. What it does:

• Protects the fan blade from debris and accidental contact
• Helps channel airflow for consistent cooling performance
• Reduces rattles or vibration caused by a loose or broken grille
• Visible damage or cracks around the fan area are common reasons to replace this part

• One grille assembly

• Disconnect power to the appliance before starting any repair
• Removal/installation typically requires basic hand tools (screwdriver) and careful alignment
• Handle the grille gently to avoid cracking plastic tabs; verify clips/screws are secure before restoring power

This fan grill assembly covers and directs airflow for the evaporator fan, helping protect the fan and maintain proper circulation inside the compartment. It replaces a cracked, broken or missing grill to restore safe airflow and component protection. What it does:

• Protects the evaporator fan from debris and prevents contact with the spinning blades
• Directs airflow for consistent circulation across the evaporator coils
• Can reduce rattling or vibration caused by a damaged or loose grill
• Helps avoid airflow restriction that contribute to cooling issues

• Disconnect power to the appliance before any service to avoid shock or injury
• Typically installs behind an interior access panel; gentle trim removal may be required
• Inspect mounting tabs and clips; replace any damaged fasteners for secure fit
• Handle plastic parts carefully to avoid cracking; do not overtighten screws

It contains the defrost temperature sensor and the defrost thermal fuse.

This DC motor is the drive component that turns the appliance's drum or agitator, restoring normal rotation and cycle performance. It replaces a worn or failed motor to help the appliance run smoothly and consistently. What it does:

• Provides rotational drive for the appliance's drum/agitator so loads can be washed, spun, or moved as intended
• Replaces motors that fail to start or run intermittently
• Stops symptoms like no-spin, reduced spin speed, or uneven operation
• Resolves abnormal motor noise, humming, or vibration related to a failing drive motor

• Disconnect power before starting any repair; confirm power is off with a meter when appropriate
• Handle the motor and shaft carefully to avoid damage; support the appliance to access the motor safely
• Reconnect all wiring and mounting hardware exactly as removed; note connector locations before disassembly

This DC motor drives the rotating component it's attached to—such as a fan blade, impeller, or gear—restoring smooth, reliable motion so your appliance can maintain the airflow or mechanical movement it was designed to deliver.

• Converts electrical power into controlled rotation for the connected part
• Restores proper airflow or mechanical movement when a motor has failed
• Common symptoms include the connected part not running, intermittent operation, unusual noise, or error codes
• Replaces a seized, noisy, or burnt-smelling motor

• Disconnect power (and water, if applicable) before servicing
• Note wire/harness orientation and routing before removal
• Transfer any reusable brackets, grommets, or the driven component (fan blade/impeller) from the original as needed
• Ensure the shaft spins freely and check for smooth, quiet operation after reassembly

The Rear Evaporator Motor Grommet is an OEM part for LG refrigerators. It's designed to secure and cushion the evaporator motor, ensuring it remains in place and operates quietly. This grommet plays a crucial role in minimizing vibrations and noise from the motor, which can otherwise lead to a disruptive refrigerator operation.

Causes of a bad Rear Evaporator Motor Grommet can result from deterioration due to cooling and thawing cycles in the refrigerator. Physical damage during cleaning or servicing may cause a loose motor fit.  

Symptoms of a malfunctioning Rear Evaporator Motor Grommet include:

• Unusual noises or vibrations from the back of the refrigerator.
• The evaporator motor shifting out of place, which can affect cooling efficiency.
• Increased wear on the evaporator motor due to lack of proper cushioning and support.

This OEM LG part is also compatible with some Kenmore models.

The Ice Dispenser Door Motor is an OEM part for LG refrigerators. This motor is responsible for the operation of the ice dispenser door, controlling its opening and closing mechanism to allow ice to be dispensed without letting warm air into the freezer. 

Symptoms of a bad Ice Dispenser Door Motor include:

• The dispenser door not opening or closing properly,
• Ice not being dispensed when activated,
• Unusual noises coming from the dispenser mechanism.

Causes of ice dispenser door motor failure can include electrical issues such as shorts or wiring problems, mechanical wear over time, or blockages that strain the motor.

This OEM LG part is also compatible with Sears/Kenmore.

A film radial capacitor used in appliance electrical assemblies to stabilize voltage and support motor and control circuits. Replaces a worn or failed film capacitor to restore consistent operation and reduce electrical noise. What it does:

• Smooths and stabilizes voltage in motor and control circuits to help maintain reliable operation
• Reduces electrical noise that can cause humming or erratic behavior in appliances
• Helps ensure consistent motor start/run performance when the capacitor is the cause of symptoms
• Commonly replaced when appliances exhibit intermittent starts, humming, or control board errors linked to compromised capacitors

• Disconnect power to the appliance before accessing electrical components
• Discharge the capacitor safely before touching terminals to avoid shock
• Observe correct polarity/terminal orientation and secure connections per OEM guidance

The Compressor Run Capacitor is an OEM part for LG refrigerators. It plays a critical role in the operation of the refrigerator's compressor by providing the necessary electrical boost to start and maintain the compressor's operation.

Causes of a bad compressor run capacitor can include electrical surges, overheating, or simply wear and tear over time. When the capacitor fails, it can no longer deliver the required electrical charge, which impacts the compressor's ability to start and run efficiently.

Symptoms of a bad compressor run capacitor include:

• The refrigerator not cooling properly
• The compressor not starting or running intermittently
• Unusual humming or clicking noises from the compressor area
• The refrigerator cycling on and off frequently

This OEM LG part is also compatible with Sears/Kenmore models.

The HARNESS ASSEMBLY is an OEM part for LG refrigerators. It is a collection of wires bundled together into a single integrated unit, electrically connecting major fridge components like lights, temperature controls, and more. A properly functioning harness is vital for signal transmission throughout the appliance.

Causes of a bad harness assembly can include wear-and-tear damage from repeated door openings, exposed wires snagging on other parts, or potential water damage degrading insulation qualities over time. 

Symptoms of a bad harness assembly include:

• Lights, temperature controls, or other features failing to work properly  
• Intermittent or unreliable operation of connected components
• Loose or disconnected wires that may cause electrical issues
• Error codes related to sensor or control board failures

This part is also compatible with Sears/Kenmore models.

Note: Evaporator with Defrost Heater

This sub PCB assembly is an electronic control board that processes inputs and switches components, coordinating specific appliance functions. Replacing a failed board can restore normal operation and resolve dead controls, error codes, or intermittent, unpredictable behavior. What it does:

• Distributes and regulates control power and switches loads via onboard relays/triacs
• Interprets signals from sensors and the user interface to execute commands
• Coordinates timing and operation of related components per the appliance's program logic
• Failure may present as no power, won't start, unresponsive or flickering display, random beeps, or recurring error codes

• 1 sub PCB assembly

• Disconnect power to the appliance before servicing; verify no voltage is present
• Use ESD protection and handle the board by the edges
• Photograph wiring; transfer connectors one at a time and ensure they are fully seated
• Secure the board with existing fasteners/standoffs; perform any required reset or diagnostic per your model's service info

This replacement ice maker assembly restores automatic ice production in your refrigerator's freezer. It is the complete maker module that fills, freezes, and ejects cubes, helping resolve no-ice, incomplete harvests, and jammed or broken ice maker issues.

• Produces and releases ice cubes into the storage bin on an automatic cycle
• Works with the refrigerator to pause ice production when the bin is full
• Can address overfilling or dripping originating at the ice maker assembly

• Disconnect power and shut off the water supply before servicing
• Transfer any model-specific brackets, covers, or wiring harnesses from the original unit if needed
• Ensure the fill tube is properly aligned and not blocked by ice; clear any frost
• After installation, restore power/water and allow time for normal ice production; run the test/reset cycle if your model provides one

This water filter assembly secures the refrigerator's replaceable water filter and routes water to the dispenser and ice maker. Replacing a cracked or leaking assembly restores proper flow and helps ensure a tight, reliable seal at the filter connection. What it does:

• Holds and seals the replaceable water filter cartridge
• Channels inlet water through the filter to the dispenser and ice maker
• Helps prevent leaks at the filter connection and housing
• Common symptoms: leaks around the filter area, low or no water to dispenser/ice maker, filter won't seat or stay in place, visible cracks on the housing

• 1 water filter assembly

• Disconnect power and shut off the water supply before servicing
• Relieve line pressure by dispensing water; place a towel to catch residual water
• Transfer fittings/lines carefully and seat connections fully; do not overtighten
• Restore water, check for leaks, and run water to purge air from the system

The Water Filter LT800P is an OEM part for LG refrigerators. This filter is designed to remove contaminants from the water supply, ensuring clean and fresh-tasting water and ice.

Causes of a bad water filter can include extended use beyond its recommended lifespan, exposure to high levels of contaminants, or damage to the filter itself.

Symptoms of a bad Water Filter LT800P include:

• Unpleasant taste or odor in the water or ice
• Reduced water flow from the dispenser
• Indicator light signaling the need for replacement
• Visible sediment or particles in the water

This OEM LG part is also compatible with Sears/Kenmore.

The Water Tank is an OEM part for LG refrigerators. This tank stores and supplies water to the refrigerator's ice maker and water dispenser, ensuring a consistent supply of fresh, filtered water. It is designed to fit securely within the refrigerator, maintaining hygiene and preventing leaks.

Over time, the water tank can become worn out, cracked, or contaminated. Common causes of a bad water tank include regular wear and tear, exposure to extreme temperatures, or damage from mishandling or improper installation.

Symptoms of a bad water tank include:

• Leaking water inside the refrigerator
• Low water flow to the dispenser or ice maker
• Unusual tastes or odors in the water
• Visible cracks or damage to the tank

This OEM LG part is also compatible with Sears/Kenmore.

Replacement tube connector (mechanical) that secures and routes tubing in compatible LG appliances, helping restore proper fluid flow and reduce leaks from loose or damaged connections. A literal OEM-style connector used where a secure tube-to-component join is required. What it does:

• Joins and secures tubing to appliance components or chassis to maintain a stable connection
• Keeps tubing aligned to prevent kinks or dislodging that can interrupt flow
• Commonly replaced when you see dripping, visible leaks, loose tubing, or poor water flow
• Fits the original mounting interface for reliable mechanical retention

• Disconnect power and shut off the water supply before starting any repairs
• Inspect tubing and nearby fittings for damage; replace any compromised tubing before installing the connector
• Seat the connector fully and secure per the appliance's service instructions; avoid overtightening which can damage tubing
• After installation, restore water and power and check the connection for leaks during a short test cycle

This water valve assembly controls water flow into the appliance, restoring proper fill and dispensing so your refrigerator can make ice and deliver water reliably. Designed as a direct replacement for the original OEM valve. What it does:

• Opens and closes to regulate incoming water for the ice maker and dispenser
• Helps stop leaks or no-water symptoms when the valve seals and solenoids are functioning
• Restores normal water flow when the valve solenoid or diaphragm has failed
• Works with the appliance's water supply and control signals to deliver measured fills

• Disconnect power and shut off the water supply before replacing the valve
• Handle connectors and tubing carefully; use proper tools to avoid damaging fittings
• Confirm water lines are clear and check for leaks after installation

This gas valve assembly controls and shuts off the flow of gas to your appliance's burner system, enabling safe ignition and steady heat. Replacing a sticking or failing valve restores reliable heating performance and consistent flame control.

• Regulates gas flow to the burner(s) as commanded by the control/thermostat
• Works with the igniter to light the flame
• Helps maintain stable gas supply for consistent heating
• Failure symptoms include no ignition, igniter glowing with no flame, intermittent heat, or a weak/uneven flame

• Disconnect power and shut off the gas supply before servicing
• Allow the appliance to cool and work in a well-ventilated area
• Transfer any fittings or brackets from the original valve if required
• After installation, restore gas and check all connections for leaks with a soapy-water solution

The Connector (Mech), Tube is an OEM part for LG refrigerators. It is used to securely connect water tubing within the refrigerator, ensuring a reliable flow of water to components such as the ice maker and water dispenser.

Causes of a bad connector can include wear and tear over time, physical damage from improper installation or handling, or degradation due to exposure to varying temperatures and water pressure.

Symptoms of a bad connector include:

• Leaks or drips around the connector area
• Reduced water flow to the ice maker or water dispenser
• Water pooling inside or around the refrigerator
• The ice maker or water dispenser not functioning properly

This OEM LG part is also compatible with Sears/Kenmore models.

This cover assembly replaces a damaged or missing control-panel cover to restore a clean appearance and protect the controls from spills, dust, and accidental contact. It fits over the appliance control area and aligns with factory mounting points. What it does

• Shields the control board and buttons from moisture, debris, and impact
• Restores a finished, factory look to the control area
• Prevents accidental button presses caused by objects or debris
• Helps reduce the chance of corrosion or shorting on exposed controls

• One cover assembly as pictured

• Disconnect power before starting any repair to avoid shock or damage
• Installation typically requires removing trim or screws and snapping or fastening the cover into place
• Handle carefully to avoid scratching the finish; use correct fasteners and alignment for a secure fit