Parts for Lg LSXS22423S/01: Mechanical Compartment Parts

This is a genuine replacement screw used to secure appliance panels and components. It restores proper fastening so panels and assemblies stay aligned and operate safely. What it does:

• Fastens panels, brackets, and small assemblies to maintain structural integrity
• Replaces missing or stripped screws that cause rattling or loose parts
• Helps stop vibration-related noise when used in its original mounting locations
• Matches the OEM fit to ensure proper alignment and clearance

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or component damage
• Disconnect power to the appliance before working on electrical components
• Replace all matching fasteners for even fit

This lower cover assembly replaces the damaged or missing lower access cover on your appliance to protect internal components and restore a finished appearance. It helps keep lint, debris and moisture away from cabinet internals. What it does:

• Protects internal wiring, ducts and components by sealing the lower cabinet area
• Restores the appliance's finished look when the existing cover is cracked, broken or missing
• Helps reduce rattling or vibration caused by loose or damaged lower trim
• Prevents debris and pet hair from entering serviceable openings

• Disconnect power (and water, if applicable) before starting any repair
• May require removal of the toe panel or front access panel; keep fasteners for reuse
• Use basic hand tools; handle plastic tabs gently to avoid breakage

The Drain Pipe Assembly is an OEM replacement part for LG refrigerators. It is a plastic tubing system that collects and removes liquid condensation from evaporator coils. Proper drainage is crucial to minimizing frost buildup and ensuring optimal cooling of food storage areas. 

Symptoms of a bad drain pipe assembly include:

• Excessive frost or ice accumulation inside the refrigerator
• Puddling or leaks detected near evaporator housing
• Slow draining allowing water to pool versus emptying fully
• Cracks or breaks in the tubing prevent complete fluid removal

Causes are typically mineral sediment clogging drainage paths or deteriorating plastic from constant use. This OEM LG replacement pipe restores reliable condensate removal to maintain peak efficiency.

This OEM LG part is also compatible with Sears/Kenmore. 

This leveling leg assembly stabilizes and levels your refrigerator so it sits solidly on the floor and the doors align correctly. Replacing a worn or stripped leg helps reduce rocking and vibration and restores smooth leveling adjustment.

• Provides height adjustment to level the cabinet on uneven floors
• Supports the unit to prevent rocking or wobbling
• Helps doors close and seal properly when the cabinet is level
• Symptoms may include persistent wobble, vibration/rattling, or a stripped/bent foot or screw

• Unplug the refrigerator and use a helper to prevent tipping injuries.
• Protect flooring; remove the kickplate/grille for access if present.
• Thread out the worn leg; hand-thread the new assembly and adjust height—do not over-extend.
• Level side-to-side and front-to-back per your owner's manual, then reattach any panels.

The Lever Dispenser is an OEM part for LG refrigerators. It is the control mechanism responsible for dispensing crushed ice and water through the refrigerator door without opening it. The lever and dispensing components are designed to withstand frequent use while retaining smooth, reliable operation. 

Causes of a bad lever dispenser can include worn parts inhibiting proper dispensing movement, cracks or damage reducing structural integrity, or mineral buildup affecting functionality over time.

Symptoms of a bad lever dispenser include:

• Difficulty or inability to dispense ice and water
• Leaks or drips around the dispenser area 
• Loose, rattling, or unresponsive lever action  
• The dispenser not activating or emptying the reservoir

This OEM LG part is also compatible with dispenser models featured on Kenmore side-by-side refrigerators.

This dispenser lever holder is the mounting bracket behind the refrigerator's dispenser paddle. It supports and aligns the lever and switch so water or ice dispenses reliably when the paddle is pressed.

• Holds and guides the dispenser lever and actuator switch inside the dispenser housing
• Provides a secure pivot point for smooth paddle movement
• Helps ensure consistent activation of water and ice dispensing
• Damage can cause a loose or stuck paddle, intermittent dispensing, or no dispense

• Disconnect power and shut off the water supply before servicing
• Remove the dispenser panel/escutcheon to access the lever assembly; note part orientation
• Transfer the lever, switch, and return spring to the new holder and secure with the original fasteners
• Restore power/water and test dispensing before reinstalling trim

The Ice Door Lever Spring is an OEM component compatible with LG refrigerators. It is part of the mechanism that opens and closes the ice door on LG French door refrigerators. Over time, springs can lose resiliency or become misaligned.

Causes may be extensive usage over years or damage like kinking that compromises spring function.

Symptoms of a bad ice door lever spring include:

• The ice door not latching fully when closed
• Difficulty opening or poor balance while moving the door
• The lever rubbing or catching instead of moving smoothly

This OEM LG part is also compatible with Sears/Kenmore side-by-side refrigerators.

This insulated duct assembly replaces a worn or damaged dryer exhaust duct to help contain heat and airflow for more efficient drying and reduced cabinet heat. Designed to restore proper venting and reduce noise from a failing duct. What it does:

• Channels exhaust air from the appliance while the insulation helps limit heat transfer to surrounding panels
• Helps maintain dryer efficiency by preserving exhaust airflow
• Reduces rattling or vibration caused by damaged or loose duct sections
• Helps prevent excessive cabinet heating and reduce felt heat near the appliance

• Disconnect power (and gas, if applicable) before beginning any repair
• Wear gloves to protect hands from sharp sheet-metal edges
• Ensure the assembly fits securely and clamps or fasteners are tightened to prevent leaks

The Ice Bucket Assembly is an OEM part for LG refrigerators. This assembly works to deliver freshly made ice from the icemaker.

Causes of a bad ice bucket assembly can include wear and tear of moving parts over time, blockages or freezing of the auger mechanism, or damage to critical components from accidental mishandling.

Symptoms of a bad ice bucket assembly include:

• Inability to eject ice or fill the bucket completely
• Grinding or chattering noises coming from the freezer area
• Melting or cracked ice due to issues with transfer from maker to bucket
• Ice backup or pileup around the icemaker

This OEM LG part is also compatible with some Kenmore models.

This refrigerator shelf assembly replaces a damaged or missing shelf to restore a stable storage surface and help keep food organized. It fits into existing shelf tracks and supports refrigerated items for everyday use. What it does:

• Provides a flat, stable surface for storing food and containers
• Replaces cracked, chipped, or broken shelving that can cause spills or unstable storage
• Restores lost shelf space when a shelf is missing or no longer secures in the tracks
• Helps maintain organized interior layout and proper use of door/compartment space

• Remove food and shelving above the installation area before you begin
• Handle glass components carefully and wear gloves to reduce cut risk
• Align the shelf with the interior tracks and slide into place until it seats securely

This freezer shelf assembly restores stable storage and organization inside the freezer compartment, supporting frozen foods and containers while maintaining proper airflow. Designed as a direct-fit replacement when the original shelf is cracked, bent, or missing. What it does:

• Replaces a damaged or missing freezer shelf to restore level, secure storage.
• Prevents items from tipping or falling through cracked or warped shelving.
• Maintains designed spacing for consistent cold-air circulation throughout the freezer.
• Helps keep frozen foods organized and easier to access.

• Unplug the refrigerator or disconnect power before starting any service.
• Remove food and glide existing shelving out slowly; lift and seat the replacement shelf into the existing supports.
• Handle edges carefully to avoid cuts; wear gloves if needed.
• If shelf clips or supports are damaged, inspect and replace those parts separately.

This replacement vegetable crisper drawer fits the refrigerator's fresh food compartment. Replace a cracked, warped, or missing bin to restore clean, organized produce storage and proper fit within the existing crisper frame and rails.

• Holds fruits and vegetables in the crisper section of the refrigerator
• Works with the original crisper cover/frame to help retain humidity around produce
• Replaces bins that are cracked, broken, stained, or that won't slide/close correctly
• Helps organize contents and contain small spills in the fresh food compartment

• No tools required; remove food, then pull the old drawer forward to the stop
• Lift the front slightly and slide the drawer straight out of the rails
• Align the new drawer with the rails and slide it in until fully seated
• Do not force the drawer; ensure the crisper cover/frame is seated correctly for smooth operation

This name plate is the exterior emblem that mounts to the appliance's front panel. It replaces a missing, cracked, or faded badge to restore a clean, factory look and cover the designated trim area.

• Attaches to the outer panel to display brand/series identification
• Restores a finished appearance where the original emblem sits
• Direct replacement for a lost, damaged, or worn badge
• Typical symptoms: missing emblem, loose or broken tabs, peeling, or discoloration

• Disconnect power before servicing the appliance
• Carefully remove the old emblem; release any tabs from behind or peel away remaining adhesive
• Clean and dry the mounting surface; remove all residue for best fit
• Align with the recess/holes and press evenly until fully seated

This small stopper fits inside the handle assembly to limit travel and keep the handle properly seated. Replacing a worn or missing stopper restores a solid, secure feel when opening and closing your appliance.

• Provides a positive stop for handle movement
• Helps keep the handle aligned and seated against its mounts
• Replaces a cracked, deformed, or missing stopper
• Common signs: handle feels loose or wobbly, over-rotates, or shifts/clicks during use

• Unplug the appliance before servicing to prevent injury
• Support the handle and protect the finish while removing fasteners
• Note the original stopper's orientation and install the new one the same way
• Tighten fasteners evenly; do not overtighten to avoid damaging plastic or finishes

This dairy bucket is the removable door bin that holds butter, cheese and small dairy items for easy access and organization. It restores a broken or missing door storage bin so food stays contained and accessible. What it does:

• Provides a dedicated, shallow storage area for butter, cheese and other small items on the refrigerator door
• Replaces cracked, broken or missing door bins that no longer stay secured or leak onto lower shelves
• Keeps dairy items contained to prevent spills and improve door organization
• Fits into the door bin track and snaps into place to hold lightweight items

• One dairy bucket

• Removes and installs by lifting or unhooking the old bin from the door rails and snapping the replacement into the same position
• Use gentle pressure to seat the bin; do not force or wedge to avoid damaging the door rail
• Clean with mild soap and water before first use and after spills; avoid abrasive cleaners
• Handle carefully to avoid chipping or cracking the plastic

This dairy bucket is the removable door bin that holds butter, cheese and small dairy items for easy access and organization. It restores a broken or missing door storage bin so food stays contained and accessible. What it does:

• Provides a dedicated, shallow storage area for butter, cheese and other small items on the refrigerator door
• Replaces cracked, broken or missing door bins that no longer stay secured or leak onto lower shelves
• Keeps dairy items contained to prevent spills and improve door organization
• Fits into the door bin track and snaps into place to hold lightweight items

• One dairy bucket

• Removes and installs by lifting or unhooking the old bin from the door rails and snapping the replacement into the same position
• Use gentle pressure to seat the bin; do not force or wedge to avoid damaging the door rail
• Clean with mild soap and water before first use and after spills; avoid abrasive cleaners
• Handle carefully to avoid chipping or cracking the plastic

This door basket is a replacement refrigerator door bin that restores secure storage on the door shelves, helping keep bottles, condiments and small items organized and upright. What it does:

• Replaces a cracked, broken or missing door bin so items no longer fall out when opening the door
• Provides a molded shelf edge to keep bottles and containers upright
• Restores original storage capacity and organization to the refrigerator door
• Designed to snap into the door shelf mounting points for a stable fit

• One refrigerator door basket

• Remove all items from the door before replacing the bin
• Align the bin with the door shelf mounting slots and press until it snaps into place
• No special tools typically required; handle with care to avoid cracking plastic

This door basket is the removable bin that mounts to the refrigerator door and holds condiments, bottles, and small items. Replacing a broken or missing bin restores usable storage space and keeps items organized and easy to access.

• Mounts to the inner door liner to securely hold food items and beverages
• Helps organize frequently used items and maximizes door storage capacity
• Replace if the bin is cracked, warped, or the mounting tabs are broken
• Common symptoms: bin falls off, won't stay seated, or is missing

• Empty the old bin and lift it up and out of the door liner slots to remove.
• Align the new basket's hooks/tabs with the slots and press down until fully seated.
• Verify the bin is level and locked in place before loading items.
• Handle plastic carefully; allow it to warm to room temperature to reduce risk of cracking.

The Door Basket is an OEM part for LG refrigerators. This basket attaches to the interior of the refrigerator door, providing additional storage space for items such as bottles, jars, and other small containers, making it easy to organize and access frequently used items.

Causes of a bad door basket can include regular wear and tear, cracks or breaks from heavy use or overloading, and accidental impact or mishandling.

Symptoms of a bad door basket include:

• Cracks or breaks in the plastic
• The basket not fitting securely in its designated location
• Difficulty holding items properly
• The basket sagging or detaching from the door

This OEM LG part is also compatible with Sears/Kenmore models.

The Door Stopper Assembly is an OEM component specifically designed for LG refrigerators. It secures the fridge door in fully closed and aligned positions. 

The stopper assembly utilizes a pneumatic cylinder and integrated mounts to softly cushion door movement. This allows for smooth closing with an audible click to confirm proper sealing.

Causes of a bad stopper assembly can include cracked or leaking air cylinders after years of use. Loose or sheared mounting hardware may also cause improper alignment and restricted closure.

Symptoms of a bad door stopper assembly include: 

• Gaps forming around the door seal when closed
• Doors difficult to latch fully or align correctly  
• Premature cooling loss from unsealed openings

Replacing this LG part restores a snug, confirmed door shut. The OEM stopper components ensure dependable closing effort for efficient operation. This replacement is compatible with some Kenmore models as well.

The Refrigerator Door Handle is an OEM replacement part for LG refrigerators. The door handle provides an easy grip point for opening and closing the refrigerator door. 

Symptoms of a bad door handle include:

• Looseness, wobbling, or detachment from the refrigerator door  
• Cracking or splitting of the plastic material
• Discoloration or warping from sun exposure

Causes can be regular wear and tear over many opening and closing cycles. Repeated force exerted by grabbing the handle may cause stress fractures. Exposure to direct sunlight's UV rays can degrade plastic over time as well.

This OEM LG part is also compatible with Sears/Kenmore refrigerators.

This upper hinge assembly supports the refrigerator door at the top and acts as the pivot point for smooth opening and closing. Replacing a worn hinge restores proper alignment and helps the door seal and close consistently.

• Supports and pivots the door at the top hinge point
• Maintains door alignment with the cabinet and gasket
• Helps ensure complete closure and proper sealing
• A worn hinge may cause door sagging, rubbing, popping/creaking noises
• Misalignment may lead to air leaks, frost, or temperature fluctuations

• Disconnect power and, if applicable, shut off the water supply.
• Remove the hinge cover, support the door, and note shim/bushing positions.
• Remove hinge screws, lift the door off, transfer any spacers/bushings, and install the new hinge.
• Align the door and verify gasket contact all around before restoring power.

This hinge lever mounts on the refrigerator door hinge to guide door movement and closure, helping the door seal properly. Replacing a worn or broken lever restores smooth operation and consistent sealing.

• Guides hinge motion so the door opens and closes smoothly
• Helps maintain door alignment for a reliable gasket seal
• Replace if the lever is visibly cracked, worn, or deformed

• Disconnect power and support the door to prevent injury or damage
• Remove the hinge cover and fasteners; note the lever's orientation before removal
• Install the new lever in the same position and reassemble the hinge components
• Adjust hinge per model procedures if needed

This replacement nut is a simple fastener used to secure internal components and panels. It restores proper attachment where a loose or missing nut causes vibration, noise, or parts to shift. What it does:

• Secures components, brackets, or panels in place to maintain appliance stability
• Prevents parts from loosening during operation, reducing rattles and vibration
• A missing or damaged nut can allow movement that leads to noise or improper alignment
• Use as a direct hardware replacement when the original nut is lost or worn

• Disconnect power (and water, if applicable) before accessing internal parts
• Start threads by hand to avoid cross-threading; tighten with the appropriate wrench or socket
• Replace if threads are stripped or the nut is damaged
• Refer to the parts diagram for the correct mounting location

The Lower Hinge Assembly is an OEM part for LG refrigerators. It is responsible for supporting the refrigerator door and allowing it to open and close smoothly. The hinge assembly ensures the door stays aligned and securely in place, preventing cold air from escaping and maintaining the efficiency of the appliance.

You should replace the lower hinge assembly if it becomes faulty. Causes of a bad lower hinge assembly can include wear and tear over time, excessive force or weight on the door, or damage from accidental impacts.

Symptoms of a bad lower hinge assembly include:

• Difficulty in opening or closing the door
• Door not sealing properly
• Squeaking or grinding noises when the door moves
• Door misalignment

This OEM LG part is also compatible with Sears/Kenmore models.

Note: Evaporator with Defrost Heater

NOTE: This part also requires software update kit CJT30000002. DO NOT INSTALL WITHOUT UPDATING SOFTWARE. Call for more information.

The Compressor is an OEM part for LG refrigerators. As the primary component that circulates refrigerant to chill the refrigerator and freezer compartments, it is crucial for proper cooling operation. The compressor works with the condenser fan and evaporator coil to regulate temperatures inside the refrigerator. 

Causes of a faulty compressor can include gradual breakdown of motor windings, loss of refrigerant pressure over time, or failure of electrical components vital to operation.

Symptoms of a bad compressor are:  

• Elevated fridge/freezer temperatures unable to be maintained
• Frost patterns indicating poor or insufficient cooling 
• Abnormal vibrations or sounds upon compressor cycling
• Error codes displayed regarding cooling performance

It is also compatible with Sears/Kenmore refrigerator models.  
 

The Compressor Overload is an OEM part for LG refrigerators. It works to prevent damage by automatically shutting off power to the compressor in the event of overheating, helping to extend the life of the compressor.

Causes of a bad compressor overload include normal wear and tear over time, extended use in high-heat conditions, or physical damage that impacts its protective functions.

Symptoms of a bad overload include:

• The compressor failing to start or run
• Strange noises coming from the compressor
• An increase in the refrigerator's operating temperature
• Frequent and unexpected shut-offs of the compressor

This OEM LG part is also compatible with Sears/Kenmore refrigerator models.

This damper cushions and isolates the refrigerator compressor to reduce vibration and noise for smoother operation. It helps maintain stable compressor mounting and prevents metal-to-metal contact that can cause wear or rattling. What it does:

• Absorbs compressor vibrations to reduce noise and movement
• Helps protect the compressor housing and mounting points from shock
• Can reduce rattling or knocking sounds originating near the compressor area
• Supports proper alignment of the compressor assembly during operation

• One compressor damper (mounting isolator)

• Turn off power at the breaker and unplug the appliance before servicing
• Inspect mounting area and hardware; replace any damaged fasteners before installing the damper
• Position the damper on the compressor mount as shown in the service manual and secure per OEM guidance

This small stopper installs in the refrigerator to limit the travel of a moving component and keep it securely in place. Replacing a broken or missing stopper prevents over-extension and helps maintain smooth, aligned operation.

• Limits the range of motion for a door, bin, or drawer to prevent over-opening or accidental removal
• Helps keep interior components aligned and operating smoothly
• Replace if cracked, missing, or deformed
• Common symptoms: drawer or bin slides out too far, door swings past normal range, or a broken plastic stop is found

• Disconnect power before servicing; remove or support the affected bin/drawer/door
• Note the old stopper's orientation and location before removal
• Transfer and reuse any original screws or clips if applicable
• Snap or fasten the new stopper in place and test for smooth movement

A replacement base assembly that secures and isolates the refrigerator compressor to reduce vibration and help maintain proper alignment. Restores stable compressor mounting for quieter, more reliable operation. What it does:

• Supports and anchors the compressor to the appliance chassis to maintain correct positioning
• Absorbs and dampens compressor vibration to reduce noise and wear
• Helps prevent compressor movement that can stress refrigerant lines and mounts
• Restores proper fit and alignment after damage or corrosion of the original base

• Mounting requires accessing the compressor area—disconnect power and fully discharge any stored energy before starting
• Follow OEM service manual for removal/installation sequence and torque values where specified
• Inspect surrounding mounts, fasteners, and refrigerant lines for damage during replacement

The Drier Assembly is an OEM part for LG refrigerators. This part is responsible for removing moisture and contaminants from the refrigerant. This ensures that the refrigerant circulates effectively and efficiently, preventing damage to other components and maintaining the refrigerator's cooling performance.

Causes of a bad Drier Assembly can include contamination from moisture entering the refrigerant lines, blockages from debris or particulates, and general wear and tear over time that reduces its effectiveness.

Symptoms of a bad Drier Assembly include:

• Reduced cooling efficiency or warm refrigerator temperatures
• Unusual noises from the refrigeration system
• The compressor running continuously or cycling frequently
• Frost buildup on the evaporator coils due to improper refrigerant flow

This OEM LG part is also compatible with Sears/Kenmore models.

This holder secures the dryer-related assembly in place to reduce movement and wear, helping maintain proper alignment and quieter operation. It's a simple replacement that restores part stability in the appliance. What it does:

• Secures a dryer assembly or component to the appliance frame to prevent shifting
• Helps reduce vibration and rubbing noises caused by a loose part
• Maintains correct alignment so related parts operate smoothly
• Used when the existing holder is cracked, broken, or missing

• Disconnect power before replacing any dryer components to avoid shock or injury
• Access location and removal steps vary by model; follow the appliance's service manual or exploded view
• Keep fasteners and adjacent parts organized for reassembly; replace any damaged clips or screws

This replacement fan assembly restores airflow in your appliance's cooling system to help maintain proper temperature and circulation. It's a direct-fit replacement designed to stop airflow-related issues and reduce noise from a failing fan. What it does:

• Circulates air across evaporator/condenser coils to support proper cooling and defrost cycles
• Replaces a worn or failed fan that can cause warm compartments or poor cooling
• Helps eliminate unusual humming, grinding, or rattling caused by a damaged fan blade or motor
• Supports even temperature distribution and can reduce frost buildup when fan operation is restored

• Disconnect power before starting; work on powered appliances can cause shock or injury
• Handle the fan blade carefully to avoid bending blades or damaging the motor
• Secure mounting fasteners to prevent vibration

The Condenser Fan Blade is an OEM replacement part for LG refrigerators. The condenser fan motor blade is located on the condenser fan motor which is usually located on or near the compressor at the back of the refrigerator. This part is responsible for circulating air over the condenser coils. This helps to remove heat from the condenser and evaporate water in the defrost drain pan.

Causes of blade failure can include normal wear over extended runtime, accumulated dirt and dust impeding airflow, or physical impact damage.

Symptoms of a faulty condenser fan blade include:

• Refrigerator fails to properly cool and maintain temperatures
• Condenser unit runs excessively as heat fails to dispel
• Abnormal noises such as grinding or squealing emanate from the condenser area

This OEM LG part is also compatible with some Sears/Kenmore model refrigerators.

This grille assembly covers and protects the refrigerator fan while helping direct airflow for proper cooling. Replacing a damaged or cracked grille restores protection and helps maintain efficient air circulation around the fan area. What it does:

• Protects the fan blade from debris and accidental contact
• Helps channel airflow for consistent cooling performance
• Reduces rattles or vibration caused by a loose or broken grille
• Visible damage or cracks around the fan area are common reasons to replace this part

• One grille assembly

• Disconnect power to the appliance before starting any repair
• Removal/installation typically requires basic hand tools (screwdriver) and careful alignment
• Handle the grille gently to avoid cracking plastic tabs; verify clips/screws are secure before restoring power

This fan grill assembly covers and directs airflow for the evaporator fan, helping protect the fan and maintain proper circulation inside the compartment. It replaces a cracked, broken or missing grill to restore safe airflow and component protection. What it does:

• Protects the evaporator fan from debris and prevents contact with the spinning blades
• Directs airflow for consistent circulation across the evaporator coils
• Can reduce rattling or vibration caused by a damaged or loose grill
• Helps avoid airflow restriction that contribute to cooling issues

• Disconnect power to the appliance before any service to avoid shock or injury
• Typically installs behind an interior access panel; gentle trim removal may be required
• Inspect mounting tabs and clips; replace any damaged fasteners for secure fit
• Handle plastic parts carefully to avoid cracking; do not overtighten screws

It contains the defrost temperature sensor and the defrost thermal fuse.

This DC motor is the drive component that turns the appliance's drum or agitator, restoring normal rotation and cycle performance. It replaces a worn or failed motor to help the appliance run smoothly and consistently. What it does:

• Provides rotational drive for the appliance's drum/agitator so loads can be washed, spun, or moved as intended
• Replaces motors that fail to start or run intermittently
• Stops symptoms like no-spin, reduced spin speed, or uneven operation
• Resolves abnormal motor noise, humming, or vibration related to a failing drive motor

• Disconnect power before starting any repair; confirm power is off with a meter when appropriate
• Handle the motor and shaft carefully to avoid damage; support the appliance to access the motor safely
• Reconnect all wiring and mounting hardware exactly as removed; note connector locations before disassembly

This DC motor drives the rotating component it's attached to—such as a fan blade, impeller, or gear—restoring smooth, reliable motion so your appliance can maintain the airflow or mechanical movement it was designed to deliver.

• Converts electrical power into controlled rotation for the connected part
• Restores proper airflow or mechanical movement when a motor has failed
• Common symptoms include the connected part not running, intermittent operation, unusual noise, or error codes
• Replaces a seized, noisy, or burnt-smelling motor

• Disconnect power (and water, if applicable) before servicing
• Note wire/harness orientation and routing before removal
• Transfer any reusable brackets, grommets, or the driven component (fan blade/impeller) from the original as needed
• Ensure the shaft spins freely and check for smooth, quiet operation after reassembly

The Rear Evaporator Motor Grommet is an OEM part for LG refrigerators. It's designed to secure and cushion the evaporator motor, ensuring it remains in place and operates quietly. This grommet plays a crucial role in minimizing vibrations and noise from the motor, which can otherwise lead to a disruptive refrigerator operation.

Causes of a bad Rear Evaporator Motor Grommet can result from deterioration due to cooling and thawing cycles in the refrigerator. Physical damage during cleaning or servicing may cause a loose motor fit.  

Symptoms of a malfunctioning Rear Evaporator Motor Grommet include:

• Unusual noises or vibrations from the back of the refrigerator.
• The evaporator motor shifting out of place, which can affect cooling efficiency.
• Increased wear on the evaporator motor due to lack of proper cushioning and support.

This OEM LG part is also compatible with some Kenmore models.

The Ice Dispenser Door Motor is an OEM part for LG refrigerators. This motor is responsible for the operation of the ice dispenser door, controlling its opening and closing mechanism to allow ice to be dispensed without letting warm air into the freezer. 

Symptoms of a bad Ice Dispenser Door Motor include:

• The dispenser door not opening or closing properly,
• Ice not being dispensed when activated,
• Unusual noises coming from the dispenser mechanism.

Causes of ice dispenser door motor failure can include electrical issues such as shorts or wiring problems, mechanical wear over time, or blockages that strain the motor.

This OEM LG part is also compatible with Sears/Kenmore.

A film radial capacitor used in appliance electrical assemblies to stabilize voltage and support motor and control circuits. Replaces a worn or failed film capacitor to restore consistent operation and reduce electrical noise. What it does:

• Smooths and stabilizes voltage in motor and control circuits to help maintain reliable operation
• Reduces electrical noise that can cause humming or erratic behavior in appliances
• Helps ensure consistent motor start/run performance when the capacitor is the cause of symptoms
• Commonly replaced when appliances exhibit intermittent starts, humming, or control board errors linked to compromised capacitors

• Disconnect power to the appliance before accessing electrical components
• Discharge the capacitor safely before touching terminals to avoid shock
• Observe correct polarity/terminal orientation and secure connections per OEM guidance

The Capacitor is an OEM part for LG refrigerators. It plays a vital role in the electrical system, providing the necessary power boost to start the compressor and maintain its operation. This component ensures that the refrigerator runs efficiently by stabilizing voltage and improving overall performance.

Common causes of a bad capacitor include electrical surges, wear and tear over time, or exposure to excessive heat.

Symptoms of a bad capacitor include:

• The refrigerator not cooling properly
• The compressor not starting or running intermittently
• Unusual noises coming from the refrigerator
• The refrigerator cycling on and off frequently

This OEM LG part is also compatible with Sears/Kenmore models.

Note: Evaporator with Defrost Heater

This is an LG refrigerator circuit board assembly, also called a PCB or printed circuit board. It manages the appliance's temperature, defrost timing, and other vital functions. If damaged, the refrigerator may have difficulty maintaining an appropriate temperature. The compressor may run constantly, or may never kick on at all.Unplug the refrigerator before installing this part. It might be a good idea to move food to temporary cool storage, as well. Remove the wire harness and mounting screws from the old control panel and install the new component in its place.This is a genuine OEM part compatible with refrigerators manufactured by LG. It is sold without any additional hardware.

This sub PCB assembly is an electronic control board that processes inputs and switches components, coordinating specific appliance functions. Replacing a failed board can restore normal operation and resolve dead controls, error codes, or intermittent, unpredictable behavior. What it does:

• Distributes and regulates control power and switches loads via onboard relays/triacs
• Interprets signals from sensors and the user interface to execute commands
• Coordinates timing and operation of related components per the appliance's program logic
• Failure may present as no power, won't start, unresponsive or flickering display, random beeps, or recurring error codes

• 1 sub PCB assembly

• Disconnect power to the appliance before servicing; verify no voltage is present
• Use ESD protection and handle the board by the edges
• Photograph wiring; transfer connectors one at a time and ensure they are fully seated
• Secure the board with existing fasteners/standoffs; perform any required reset or diagnostic per your model's service info

This replacement ice maker assembly restores automatic ice production in your refrigerator's freezer. It is the complete maker module that fills, freezes, and ejects cubes, helping resolve no-ice, incomplete harvests, and jammed or broken ice maker issues.

• Produces and releases ice cubes into the storage bin on an automatic cycle
• Works with the refrigerator to pause ice production when the bin is full
• Can address overfilling or dripping originating at the ice maker assembly

• Disconnect power and shut off the water supply before servicing
• Transfer any model-specific brackets, covers, or wiring harnesses from the original unit if needed
• Ensure the fill tube is properly aligned and not blocked by ice; clear any frost
• After installation, restore power/water and allow time for normal ice production; run the test/reset cycle if your model provides one

This water filter assembly secures the refrigerator's replaceable water filter and routes water to the dispenser and ice maker. Replacing a cracked or leaking assembly restores proper flow and helps ensure a tight, reliable seal at the filter connection. What it does:

• Holds and seals the replaceable water filter cartridge
• Channels inlet water through the filter to the dispenser and ice maker
• Helps prevent leaks at the filter connection and housing
• Common symptoms: leaks around the filter area, low or no water to dispenser/ice maker, filter won't seat or stay in place, visible cracks on the housing

• 1 water filter assembly

• Disconnect power and shut off the water supply before servicing
• Relieve line pressure by dispensing water; place a towel to catch residual water
• Transfer fittings/lines carefully and seat connections fully; do not overtighten
• Restore water, check for leaks, and run water to purge air from the system

The Water Filter LT800P is an OEM part for LG refrigerators. This filter is designed to remove contaminants from the water supply, ensuring clean and fresh-tasting water and ice.

Causes of a bad water filter can include extended use beyond its recommended lifespan, exposure to high levels of contaminants, or damage to the filter itself.

Symptoms of a bad Water Filter LT800P include:

• Unpleasant taste or odor in the water or ice
• Reduced water flow from the dispenser
• Indicator light signaling the need for replacement
• Visible sediment or particles in the water

This OEM LG part is also compatible with Sears/Kenmore.

The Water Tank is an OEM part for LG refrigerators. This tank stores and supplies water to the refrigerator's ice maker and water dispenser, ensuring a consistent supply of fresh, filtered water. It is designed to fit securely within the refrigerator, maintaining hygiene and preventing leaks.

Over time, the water tank can become worn out, cracked, or contaminated. Common causes of a bad water tank include regular wear and tear, exposure to extreme temperatures, or damage from mishandling or improper installation.

Symptoms of a bad water tank include:

• Leaking water inside the refrigerator
• Low water flow to the dispenser or ice maker
• Unusual tastes or odors in the water
• Visible cracks or damage to the tank

This OEM LG part is also compatible with Sears/Kenmore.

Replacement tube connector (mechanical) that secures and routes tubing in compatible LG appliances, helping restore proper fluid flow and reduce leaks from loose or damaged connections. A literal OEM-style connector used where a secure tube-to-component join is required. What it does:

• Joins and secures tubing to appliance components or chassis to maintain a stable connection
• Keeps tubing aligned to prevent kinks or dislodging that can interrupt flow
• Commonly replaced when you see dripping, visible leaks, loose tubing, or poor water flow
• Fits the original mounting interface for reliable mechanical retention

• Disconnect power and shut off the water supply before starting any repairs
• Inspect tubing and nearby fittings for damage; replace any compromised tubing before installing the connector
• Seat the connector fully and secure per the appliance's service instructions; avoid overtightening which can damage tubing
• After installation, restore water and power and check the connection for leaks during a short test cycle

This water valve assembly controls water flow into the appliance, restoring proper fill and dispensing so your refrigerator can make ice and deliver water reliably. Designed as a direct replacement for the original OEM valve. What it does:

• Opens and closes to regulate incoming water for the ice maker and dispenser
• Helps stop leaks or no-water symptoms when the valve seals and solenoids are functioning
• Restores normal water flow when the valve solenoid or diaphragm has failed
• Works with the appliance's water supply and control signals to deliver measured fills

• Disconnect power and shut off the water supply before replacing the valve
• Handle connectors and tubing carefully; use proper tools to avoid damaging fittings
• Confirm water lines are clear and check for leaks after installation

This gas valve assembly controls and shuts off the flow of gas to your appliance's burner system, enabling safe ignition and steady heat. Replacing a sticking or failing valve restores reliable heating performance and consistent flame control.

• Regulates gas flow to the burner(s) as commanded by the control/thermostat
• Works with the igniter to light the flame
• Helps maintain stable gas supply for consistent heating
• Failure symptoms include no ignition, igniter glowing with no flame, intermittent heat, or a weak/uneven flame

• Disconnect power and shut off the gas supply before servicing
• Allow the appliance to cool and work in a well-ventilated area
• Transfer any fittings or brackets from the original valve if required
• After installation, restore gas and check all connections for leaks with a soapy-water solution

The Connector (Mech), Tube is an OEM part for LG refrigerators. It is used to securely connect water tubing within the refrigerator, ensuring a reliable flow of water to components such as the ice maker and water dispenser.

Causes of a bad connector can include wear and tear over time, physical damage from improper installation or handling, or degradation due to exposure to varying temperatures and water pressure.

Symptoms of a bad connector include:

• Leaks or drips around the connector area
• Reduced water flow to the ice maker or water dispenser
• Water pooling inside or around the refrigerator
• The ice maker or water dispenser not functioning properly

This OEM LG part is also compatible with Sears/Kenmore models.

This mechanical mounting band secures a bracket assembly inside the appliance to keep components aligned and reduce vibration. It restores proper bracket positioning so moving parts run quietly and reliably. What it does:

• Holds a bracket or component assembly in place to maintain proper alignment
• Dampens movement and reduces vibration-related noise or rattling
• Prevents excess wear by keeping parts from shifting during operation
• Helps maintain correct clearances to avoid interference or rubbing

• Disconnect power before inspecting or replacing internal parts
• Remove only the fasteners necessary to access the bracket; keep track of hardware
• Secure all fasteners to the manufacturer's torque or snug specification
• Replace the band if bent, cracked, or missing to restore proper fit and function

This cover assembly replaces a damaged or missing control-panel cover to restore a clean appearance and protect the controls from spills, dust, and accidental contact. It fits over the appliance control area and aligns with factory mounting points. What it does

• Shields the control board and buttons from moisture, debris, and impact
• Restores a finished, factory look to the control area
• Prevents accidental button presses caused by objects or debris
• Helps reduce the chance of corrosion or shorting on exposed controls

• One cover assembly as pictured

• Disconnect power before starting any repair to avoid shock or damage
• Installation typically requires removing trim or screws and snapping or fastening the cover into place
• Handle carefully to avoid scratching the finish; use correct fasteners and alignment for a secure fit

This holder is a small mounting bracket that secures a mating component in place inside the appliance. Replacing a cracked or missing holder restores a firm, rattle-free fit and proper alignment.

• Provides a stable mount for the designated part
• Prevents shifting and vibration that can cause noise or premature wear
• Common signs of failure: broken tabs, stress cracks, or the attached part sagging or falling out
• When damaged, the connected component may be loose, noisy, or misaligned

• Disconnect power; if working near water tubing, also shut off the water supply
• Note the original orientation and mounting points; take a photo before removal
• Reuse existing fasteners and avoid overtightening to prevent cracking the plastic
• Ensure the attached component is secure and clears any moving parts before restoring power

The Refrigerator Temperature Sensor is an OEM part for LG refrigerators. This sensor monitors the temperature inside the refrigerator and communicates with the control board to maintain the optimal cooling environment.

Common causes of failure include wear and tear over time, electrical issues, or exposure to moisture. A malfunctioning sensor can lead to inaccurate temperature readings, resulting in improper cooling or freezing.

Symptoms of a bad refrigerator temperature sensor include:

• Inconsistent refrigerator or freezer temperatures
• Food spoiling faster than usual
• Refrigerator running continuously or not running at all
• Error codes displayed on the control panel

This OEM LG part is also compatible with Sears/Kenmore models.