Parts for Crosley CDE7700LR0: Motor Parts

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

This locking clip secures the fan/blower housing in place to keep the airflow path sealed and stable. Replacing a worn or missing lock helps eliminate rattles and air leaks for consistent, quiet operation. What it does:

• Secures the fan/blower housing to its mounting points to prevent movement
• Helps maintain a tight seal for proper airflow through the exhaust path
• May correct rattling, vibration, or scraping noises from the blower area
• A loose or missing lock can allow the housing to shift, causing air leaks and reduced performance

• Fan housing lock

• Disconnect electrical power; if applicable, shut off gas supply before servicing
• Access the blower/fan housing by removing the appropriate access panel(s)
• Note orientation, then release and replace the lock; ensure the housing seats fully and evenly
• Clear lint from the area and verify the blower wheel spins freely before reassembly and testing

A single replacement screw used to secure appliance trim, panels, or interior components. Replaces lost or damaged fasteners so panels and assemblies stay firmly attached and appliances operate safely. What it does:

• Secures trim pieces, control panels, brackets, or interior components
• Restores proper fit and alignment when panels are loose or rattling
• Helps eliminate vibration noise caused by missing or stripped screws
• Used wherever the OEM screw specification is required for reliable fastening

• Install with the matching screwdriver or driver bit; avoid over-tightening to prevent stripping
• Disconnect power and remove or support panels as needed for safe access
• If screw threads are damaged, replace with the exact OEM screw to ensure secure fit

The Outlet Thermal Fuse is an OEM part for Frigidaire dryers. It acts as a safety device that protects the dryer from overheating by cutting off the power if the temperature exceeds a safe level. This ensures the dryer operates safely and helps prevent potential fire hazards.

Causes of a bad thermal fuse can include lint buildup blocking airflow, overloading the dryer, or mechanical failures in the heating element. These issues can cause the dryer to overheat, leading to the fuse blowing as a protective measure.

Symptoms of a bad outlet thermal fuse include:

• The dryer not starting
• The dryer running but not heating
• Sudden stopping during a cycle
• No power to the dryer

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Blower Housing Assembly is an OEM part for Frigidaire dryers. It houses the blower wheel, which circulates air through the dryer drum and out the exhaust. This assembly ensures that hot air is efficiently directed through the dryer to dry clothes properly.

Over time, the blower housing assembly can become damaged or worn out, affecting the dryer's performance. Causes of a bad blower housing assembly can include accumulation of lint or debris, wear and tear from frequent use, or physical damage to the housing or blower wheel.

Symptoms of a bad Blower Housing Assembly include:

• Reduced or no airflow from the dryer vent
• Unusual noises during operation
• Clothes taking longer to dry
• Overheating or frequent cycling off of the dryer

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This small spacer fits on the idler assembly shaft to properly space and align the belt tensioner. Replacing a worn spacer helps keep the drive belt tracking correctly so the drum/tub runs smoothly and quietly. What it does:

• Spaces and centers the idler pulley on its shaft
• Helps maintain proper belt alignment and tension
• Can reduce squeaking or chirping from the idler area
• A worn or missing spacer may let the belt ride off, fray, or stop the drum/tub

• 1 idler spacer

• Disconnect power before servicing; let hot components cool
• Access the idler assembly per your model, relieve belt tension, and remove retaining hardware to slide off the pulley and old spacer
• Install the new spacer in the same location/orientation; reassemble and route the belt correctly
• Rotate the drum/tub by hand to verify smooth belt tracking before restoring power

The Control Thermistor is an OEM part for Frigidaire dryers. This component plays a critical role in regulating the temperature inside the dryer by monitoring the internal conditions and sending temperature data to the control board. The control board then uses this information to adjust the heat cycle, ensuring clothes dry evenly and safely. 

Symptoms of a failing control thermistor include:

• Clothes not drying properly or cycles running too hot or too cold
• Frequent stopping or starting of the dryer
• Error messages related to temperature or sensor issues displayed on the control panel

Causes of control thermistor failure generally involve faulty wiring, accumulation of lint and debris affecting the sensor's accuracy, or wear and tear from regular use that leads to degradation of the sensor components.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This hex head screw spacer is a replacement threaded fastener that secures and spaces components while cutting its own thread in softer mating material for a tight fit. It's useful for repairs where the original spacer screw is missing or damaged. What it does:

• Acts as a spacer and fastener to hold panels, brackets, or assemblies at a set distance
• Thread-cutting tip forms secure threads in compatible materials for reliable engagement
• Helps stop movement or vibration of connected parts that can cause noise or wear
• Commonly used where the original hex-head spacer screw is corroded, stripped, or broken

• Use the correct screwdriver or wrench on the hex head to avoid rounding the fastener
• Start threads straight and apply steady pressure; do not force if resistance indicates misalignment
• Use appropriate torque — overtightening can strip the formed threads or damage parts
• Wear eye protection and follow appliance power/disconnect safety before servicing

This idler spring attaches to the idler arm to keep the drive belt properly tensioned, preventing slip and chatter. Replacing a weak or broken spring restores steady rotation and helps reduce noise and belt wear.

• Maintains correct belt tension by pulling the idler arm into position
• Helps prevent belt slippage, squealing/chirping, and premature belt wear
• A failed spring can cause no or intermittent rotation and the belt coming off
• Typical signs include a loose belt, off-track belt, or rhythmic squeak from the base

• Disconnect power before servicing; if working on a gas appliance, shut off the gas supply
• Access the idler assembly; note belt routing before removal
• Relieve belt tension, then move the idler arm to remove and replace the spring on the same mounting holes
• After reassembly, rotate by hand to verify smooth belt tracking before test

The Idler Arm Assembly is an OEM replacement part for Frigidaire clothes dryers. It is a pulley assembly that helps to guide the dryer belt and keep it aligned. The idler arm assembly is typically located on the front of the dryer, near the dryer drum.

Causes for replacement include worn bushings or broken linkage from constant mechanical movement over several years.

Symptoms of a faulty idler arm assembly are:

• Dryer drum failure to rotate or revolve during the cycle
• Unusual vibrations, clunks, or knocks from within the dryer
• door during operation
• Slipping or shredding belts from lack of pulley engagement

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

The Drive Belt is an OEM replacement part for Frigidaire dryers. It plays a crucial role in transferring the rotational motion from the dryer's motor to the drum, enabling the tumbling action necessary for drying clothes.

Symptoms of a need to replace the drive belt include:

• The dryer drum not turning or rotating during cycles
• Loud thumping or squeaking noises coming from the dryer
• Visible wear, cracks, or fraying on the existing belt

Causes of a faulty drive belt can include general wear and tear over extended use, exposure to high temperatures or lint buildup, physical damage from foreign objects, or manufacturing defects in the belt material or construction.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore dryer models. 

The Motor Mounting Clamp is an OEM part for Frigidaire dryers. This clamp secures the motor in place within the dryer, ensuring it operates smoothly and remains stable during the drying cycles. The motor mounting clamp is essential for maintaining the proper alignment and function of the dryer motor.

Over time, the motor mounting clamp can become worn out or damaged due to constant vibration and movement. Accidental impacts or mishandling during maintenance can also cause the clamp to fail, leading to motor misalignment or instability.

Symptoms of a bad motor mounting clamp include:

• Excessive noise or vibration during the drying cycle
• Motor shifting or moving within the dryer
• Reduced drying efficiency
• The dryer not starting or stopping abruptly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Dryer Motor is an OEM part for Frigidaire dryers. It is responsible for turning the drum and the blower wheel to circulate air through the dryer, enabling efficient drying of clothes.

The dryer motor can become faulty due to normal wear and tear, electrical issues, or overheating. If the motor fails, the dryer will not be able to operate correctly.

Symptoms of a bad dryer motor include:

• The drum not spinning
• The dryer not starting or shutting off mid-cycle
• Unusual noises such as humming, buzzing, or grinding
• A burning smell or overheating

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This is a Phillips pan head machine screw commonly used to secure panels and components in appliances. It provides a reliable, low-profile head for flush fastening and easy Phillips-driver installation. What it does:

• Fastens trim, panels, or internal components where a pan head screw is required
• Designed for secure grip in metal or threaded inserts compatible with #10-16 threads
• Helps prevent loosening from vibration when installed to correct torque
• Often used in refrigeration and major appliance assemblies in limited quantities

• One Phillips pan head screw (#10-16 x 5/8")

• Use the correct #2 Phillips driver and steady pressure to avoid cam-out or stripping
• Do not overtighten; stop when snug to avoid damaging threads or mating parts
• Replace only with an identical thread size and head style to ensure fit
• Wear safety glasses when working around sharp sheet metal and springs