Parts for Crosley CDE7700LR0: Front Panel / Lint Filter Parts

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Replacement grill trim that restores your appliance's exterior finish and helps direct airflow. Use this grill when the original piece is cracked, missing, loose, or cosmetically damaged to regain a clean, finished appearance. What it does:

• Covers and protects internal components behind the appliance front or vent area.
• Helps direct airflow and reduce drafts around the appliance opening.
• Prevents debris or fingers from contacting internal parts.
• Stops rattling or vibration caused by a bent or loose grill.
• Restores the appliance's original look when the factory grill is damaged.

• Disconnect power at the breaker and allow the appliance to cool before starting any work.
• Remove existing fasteners or clips; retain original screws if they are reusable.
• Align the new grill, then secure with the original hardware; avoid over-tightening to prevent cracking.

This insulator is a small foam/trim piece that cushions and thermally isolates appliance panels to help maintain proper airflow and reduce vibration. It preserves fit between cabinet components for quiet, efficient operation. What it does:

• Cushions panels and components to reduce rattling or vibration noise
• Creates a thermal barrier that helps limit heat transfer between parts
• Keeps panels aligned and spaced to prevent rubbing or abrasion
• Worn or missing insulators can cause noise, vibration, or poor panel fit

• One insulator as shown

• Disconnect power before accessing panels or internal components
• Replace only the worn or damaged insulator; trim or adhesive may be needed to position some styles
• Remove surrounding trim or panels as required to reach the mounting location

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

The Door Catch is an OEM part for Frigidaire dryers. It secures the door closed during cycles. This allows the machine to safely run without the risk of the door opening, which could pause the drying process or pose a safety hazard. Constructed from durable materials, this door catch is designed to endure the frequent opening and closing of the dryer door, offering reliability and longevity.

Causes of a bad door catch include mechanical wear from regular use, accidental damage, or misalignment of the door.

Symptoms of a bad Door Catch include:

• The dryer door won't stay shut during cycles
• Difficulty closing the dryer door securely
• The need to apply extra force to close the door
• The dryer stops running due to the door opening mid-cycle

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Color: white. It measures about 13 inches wide by 11-1/2 inches high.

This clip is a hose clamp used in select laundry appliances. It secures a hose connection to prevent leaks and keep water or air moving where it should, helping maintain reliable washer or dryer performance.

• Secures hose to its fitting to prevent leaks or disconnections
• Helps resolve issues like leaking at a hose joint, loose hose, or poor draining/airflow related to a slipped hose
• Durable spring-style clamp designed for repeatable tension
• Commonly used on internal washer or dryer hose connections

• Unplug the appliance and turn off water supply before service
• Have a towel or pan ready for residual water when removing hoses
• Use pliers to compress and slide the clamp; note original clamp position for reassembly
• Inspect hose ends for cracks; replace the hose if damaged before reinstalling the clamp

The Door Hinge is an OEM part for Frigidaire dryers. This hinge allows it to open and close properly while maintaining a secure seal during the drying cycle.

Causes of a bad door hinge can include wear and tear from regular use, rust or corrosion due to exposure to moisture, or damage from accidental impacts. 

Symptoms of a bad door hinge include:

• Difficulty opening or closing the dryer door
• The door not sealing properly, leading to heat loss
• Squeaking or creaking noises when moving the door
• Visible damage or rust on the hinge

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Support Roller Washer is an OEM part for Frigidaire dryers, designed to ensure the smooth and stable operation of the dryer drum. Positioned between the support roller and the shaft, this washer plays a critical role in reducing friction and wear, allowing the drum to rotate smoothly and quietly.

Causes of these symptoms often stem from normal wear and tear, which can lead to the degradation of the washer over time.  

Symptoms of a bad Dryer Support Roller Washer include:

• Unusual noises, such as squeaking or grinding, indicating increased friction during drum rotation
• The dryer drum appears to wobble or is misaligned during operation
• Increased vibration of the dryer, which can lead to wear on other components

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Roller Assembly is an OEM replacement part specific to Frigidaire-brand clothes dryers. It contains multiple smooth-rolling cylinders that guide the dryer drum assembly as it turns. 

Symptoms of a faulty dryer roller assembly include: 

• Noisy or rumbling sounds from the dryer cabinet during cycles 
• Vibrating of the dryer body instead of steady drum rotation
• Physical signs like cracked rollers or worn tracks that hold them  

Causes can be seized or corroded rollers failing to spin freely. Dented tracks prevent proper alignment. Over decades, components have worn down from continuous operation.

The part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This OEM fastener replaces a worn, stripped, or missing nut to securely hold components in place inside compatible laundry appliances. Restores proper clamping force to reduce vibration, rattling, and loosening during operation. What it does:

• Secures a mating bolt or stud to keep brackets, panels, or rotating parts firmly mounted
• Restores proper tension after the original nut is lost, corroded, or damaged
• Helps address symptoms like excessive vibration, rattling, or loose assemblies
• Maintains a tight connection in high-vibration environments when properly tightened

• 1 nut

• Disconnect power (and water to a washer) before servicing
• Support the component being fastened; hold the bolt head while loosening/tightening the nut
• Start threads by hand to avoid cross-threading; tighten to manufacturer guidance
• Replace any damaged bolts or hardware it mates with for a secure repair

This replacement gasket restores a tight, reliable seal between mating parts in your appliance. It helps contain water or air at the joint to prevent leaks, odors, and performance issues.

• Creates a compressible barrier that prevents leaks at the sealed interface
• Helps maintain proper containment/airflow, depending on application
• Replace if torn, cracked, shrunken, or permanently flattened
• Typical symptoms include moisture or drips at the seam, musty odors, or visible damage

• Disconnect power; shut off water supply if applicable before servicing
• Use your model's parts diagram to locate and orient
• Clean and dry mating surfaces; remove any old adhesive or residue so the new seal seats properly
• Reassemble evenly, avoid over-tightening fasteners, and test for leaks after reassembly

This genuine replacement door gasket seals the refrigerator door to keep cold air in and reduce energy loss. It helps maintain consistent temperatures and prevents drafts and moisture buildup around the door. What it does:

• Creates an airtight seal between the door and cabinet to preserve internal temperature
• Helps prevent frost and condensation by stopping warm, humid air from entering
• Reduces compressor run time by minimizing cold-air leakage
• Commonly replaced when the seal is torn, compressed, warped, or no longer seals fully

• One door gasket

• Clean mating surfaces and remove old gasket adhesive before installing the new gasket
• Gasket may need to be warmed and flexed for proper seating; follow OEM fitting guidance
• Check for even compression around the door; do not overtighten or force the gasket
• Disconnect power or follow safety guidelines per appliance before performing service

The Door Strike is an OEM part for Frigidaire dryers. It is a small, essential component that ensures the dryer door remains securely closed during operation. The door strike engages with the door catch to keep the door latched, allowing the dryer to operate efficiently and safely. Without a functioning door strike, the dryer may not start, or it could stop mid-cycle.

You should replace this door strike if it becomes damaged or worn out. Over time, the door strike can suffer from wear due to regular use, misalignment, or accidental impact, leading to issues with the dryer door latching properly.

Symptoms of a bad door strike include:

• The dryer door not staying closed
• The dryer not starting or stopping unexpectedly
• Difficulty in latching the dryer door

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

This replacement door glass forms the clear window in the door of select front-load units, restoring safe visibility and proper door fit. Replace a cracked, chipped, or shattered pane to prevent leaks and ensure the door seals and latches correctly. What it does

• Creates the viewing window in the door and mates to the door gasket/boot
• Helps maintain a proper seal to contain wash action
• Restores safe operation when the original glass is damaged
• Common symptoms: visible cracks or shattering, water leaking from the door area, door not closing flush, rattling glass

• 1 door glass pane

• Disconnect power and turn off water supply before service
• Wear cut-resistant gloves and eye protection; handle glass carefully
• Remove the door, set it on a padded surface, and transfer trim/gasket as designed
• Tighten fasteners evenly and check gasket alignment to prevent leaks

Restore visibility inside your appliance. This lamp assembly replaces a damaged or failed interior light so you can clearly see contents when the door opens, helping maintain safe, reliable illumination in the cabinet/drum.

• Provides interior illumination when the door opens or when the control calls for light
• Houses the bulb and makes the electrical connection
• Common symptoms: no interior light, flickering/intermittent light, or heat-damaged/burned socket or housing

• Disconnect power before servicing to avoid electrical shock
• Access the lamp from the interior or service panel per model
• Install a bulb with the correct type and wattage specified for your model
• Test light operation before reassembling panels

This factory fastener secures appliance components and cabinet panels. Replacing a stripped, rusted, or missing screw restores a tight fit, reduces rattles and vibration, and keeps parts aligned for reliable operation. What it does:

• Fastens brackets, panels, and internal components to the cabinet/frame
• Helps maintain alignment and stability under vibration
• Direct replacement when the original is lost, corroded, or threads are damaged
• Common symptoms: loose or rattling panels, gaps/misalignment, or visibly missing hardware

• 1 screw

• Disconnect power; shut off gas/water if applicable before servicing
• Support the panel or component while removing/starting screws
• Match location and length to the original; start threads by hand to avoid cross-threading
• Tighten snugly—do not overtighten to prevent stripping

This T-plug electrical connector secures a reliable connection between wiring harnesses and appliance components, restoring proper power and signal flow for affected circuits. It's a direct-fit replacement when the plug is damaged or corroded. What it does:

• Provides a secure electrical connection between the harness and the appliance component
• Restores power or signal to components when a broken or loose plug causes intermittent or no operation
• Replaces melted, cracked, or corroded connectors that can cause poor contact
• Helps prevent arcing and further wiring damage when properly seated

• One T-plug electrical connector

• Disconnect power to the appliance before starting any work
• Verify connector orientation and fully seat the T-plug until it clicks or is firmly retained
• Inspect mating harness and terminals for damage or corrosion; replace harness if terminals are compromised
• Use basic hand tools; follow proper electrical and appliance safety practices

This retainer is a small fastener that secures a component inside your appliance, keeping it correctly positioned during operation. Replacing a damaged or missing retainer helps eliminate looseness and noise while preventing wear from parts shifting.

• Holds a mating part or assembly firmly in place
• Restores proper fit when the original retainer is cracked, warped, or missing
• Common symptoms: loose or misaligned parts, rattling/vibration, rubbing noises
• Helps prevent premature wear from movement or chafing

• Disconnect power; shut off gas and water supplies if applicable
• Use your model's diagram to locate the retainer and match its orientation
• Transfer any reusable hardware and ensure the retainer is fully seated
• Reassemble and run a short test to check for proper operation

Restore visibility inside your appliance. This lamp assembly replaces a damaged or failed interior light so you can clearly see contents when the door opens, helping maintain safe, reliable illumination in the cabinet/drum.

• Provides interior illumination when the door opens or when the control calls for light
• Houses the bulb and makes the electrical connection
• Common symptoms: no interior light, flickering/intermittent light, or heat-damaged/burned socket or housing

• Disconnect power before servicing to avoid electrical shock
• Access the lamp from the interior or service panel per model
• Install a bulb with the correct type and wattage specified for your model
• Test light operation before reassembling panels

The High Temperature Adhesive is an OEM part for Frigidaire appliances. This adhesive is specifically formulated to withstand high temperatures and is used in various repair applications within appliances such as ovens, ranges, and dryers.The 1-ounce tube contains adhesive formulated to withstand the extreme heat inside dryer drums and cabinets

Causes of a bad adhesive can include exposure to extremely high temperatures over extended periods, contamination by dirt or grease, or the natural aging and drying out of the adhesive.

Symptoms of a bad high temperature adhesive include:

• Components or parts becoming loose or detached
• The adhesive becoming brittle or cracked
• Inability to properly bond surfaces exposed to high heat
• Visible deterioration or peeling of the adhesive

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.