Parts for Electrolux EWMGD70JMB0: 09 - Motor Parts

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

A single replacement screw used to secure appliance trim, panels, or interior components. Replaces lost or damaged fasteners so panels and assemblies stay firmly attached and appliances operate safely. What it does:

• Secures trim pieces, control panels, brackets, or interior components
• Restores proper fit and alignment when panels are loose or rattling
• Helps eliminate vibration noise caused by missing or stripped screws
• Used wherever the OEM screw specification is required for reliable fastening

• Install with the matching screwdriver or driver bit; avoid over-tightening to prevent stripping
• Disconnect power and remove or support panels as needed for safe access
• If screw threads are damaged, replace with the exact OEM screw to ensure secure fit

The Outlet Thermal Fuse is an OEM part for Frigidaire dryers. It acts as a safety device that protects the dryer from overheating by cutting off the power if the temperature exceeds a safe level. This ensures the dryer operates safely and helps prevent potential fire hazards.

Causes of a bad thermal fuse can include lint buildup blocking airflow, overloading the dryer, or mechanical failures in the heating element. These issues can cause the dryer to overheat, leading to the fuse blowing as a protective measure.

Symptoms of a bad outlet thermal fuse include:

• The dryer not starting
• The dryer running but not heating
• Sudden stopping during a cycle
• No power to the dryer

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Blower is an OEM part for Frigidaire dryers. It is responsible for circulating hot air throughout the dryer drum, ensuring even drying of clothes. The blower also helps expel moist air through the exhaust vent.

Causes of a bad blower can include wear and tear from regular use, accumulation of lint or debris, or damage from foreign objects entering the blower housing.

Symptoms of a bad blower include:

• Clothes taking longer than usual to dry
• Insufficient airflow or no air movement through the dryer vent
• Unusual noises during the drying cycle
• The dryer overheating or shutting down unexpectedly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Replace a failed thermistor with this factory temperature sensor. It monitors temperature and feeds that data to the control, helping the appliance regulate heat and run cycles correctly. A faulty sensor can cause temperature-related performance issues.

• Senses temperature and sends a resistance signal to the control board for regulation
• Helps maintain proper heating/temperature during operation
• Failure may cause no heat or overheating, erratic or extended cycles, or temperature/sensor error codes
• Replace when sensor is open/shorted or readings are out of range per service diagnostics

• Disconnect power before servicing; if applicable, also shut off water or gas supply
• Access the sensor, unplug the wire connector, and remove any mounting screw/clip
• Install the new sensor; transfer any bracket/seal from the original and route wiring away from hot or moving parts
• Run a diagnostic or test cycle after replacement to confirm normal operation

This hex head screw spacer is a replacement threaded fastener that secures and spaces components while cutting its own thread in softer mating material for a tight fit. It's useful for repairs where the original spacer screw is missing or damaged. What it does:

• Acts as a spacer and fastener to hold panels, brackets, or assemblies at a set distance
• Thread-cutting tip forms secure threads in compatible materials for reliable engagement
• Helps stop movement or vibration of connected parts that can cause noise or wear
• Commonly used where the original hex-head spacer screw is corroded, stripped, or broken

• Use the correct screwdriver or wrench on the hex head to avoid rounding the fastener
• Start threads straight and apply steady pressure; do not force if resistance indicates misalignment
• Use appropriate torque — overtightening can strip the formed threads or damage parts
• Wear eye protection and follow appliance power/disconnect safety before servicing

The Drive Belt is an OEM replacement part for Frigidaire dryers. It plays a crucial role in transferring the rotational motion from the dryer's motor to the drum, enabling the tumbling action necessary for drying clothes.

Symptoms of a need to replace the drive belt include:

• The dryer drum not turning or rotating during cycles
• Loud thumping or squeaking noises coming from the dryer
• Visible wear, cracks, or fraying on the existing belt

Causes of a faulty drive belt can include general wear and tear over extended use, exposure to high temperatures or lint buildup, physical damage from foreign objects, or manufacturing defects in the belt material or construction.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore dryer models. 

The Motor Mounting Clamp is an OEM part for Frigidaire dryers. This clamp secures the motor in place within the dryer, ensuring it operates smoothly and remains stable during the drying cycles. The motor mounting clamp is essential for maintaining the proper alignment and function of the dryer motor.

Over time, the motor mounting clamp can become worn out or damaged due to constant vibration and movement. Accidental impacts or mishandling during maintenance can also cause the clamp to fail, leading to motor misalignment or instability.

Symptoms of a bad motor mounting clamp include:

• Excessive noise or vibration during the drying cycle
• Motor shifting or moving within the dryer
• Reduced drying efficiency
• The dryer not starting or stopping abruptly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This part is a genuine OEM replacement drive motor intended for use with dryer models. The drive motor works by rotating the drive belt, which in turn spins the dryer drum. A faulty motor could cause the drum to stop spinning altogether, or the user may notice a loud sound coming from the dryer when the drum tries to rotate. Work gloves should be worn, and the dryer should be unplugged from the power outlet before proceeding.This part was made by Frigidaire and has been sourced directly from the manufacturer. It is made out of high-quality, durable, non-corrosive materials to ensure the best possible durability. This drive motor is sold individually. It is intended for use with dryer models manufactured by Frigidaire, Electrolux, Gibson, Westinghouse, and other brands.

This is a mounting bracket that secures and supports appliance components, helping keep panels and assemblies aligned for stable operation. It's a simple replacement part that restores proper fit and reduces movement or rattling. What it does:

• Secures and supports a panel or internal assembly to the appliance frame
• Keeps components aligned to prevent binding or misalignment
• Reduces vibration and rattling caused by loose fittings
• Restores proper mechanical support after breakage or wear

• Disconnect power and/or water to the appliance before beginning any repair
• Use appropriate hand tools; keep track of fasteners and any shims or clips
• Beware of sharp sheet-metal edges; wear gloves and eye protection

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic