Parts for Frigidaire BADMODEL1: Motor And Pump Parts

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.

Dishes not drying or staying wet after cycle? This heating element heats water for cleaning and air for drying. Most DIYers replace in under 30 minutes.

Secures the lower spray arm in place. Replace if tabs are broken, worn, or missing, causing the spray arm to detach or not lock down properly. Installs under filter.

Seals the connection between the dishwasher tub and sump assembly. Replace if water leaks from the base or the gasket appears cracked or flattened.

Replacement center spray arm for your dishwasher. Installs in the middle spray position. Order a new one if yours is melted, cracked, or clogged.

Replaces a cracked, broken, or damaged lower spray arm in your dishwasher. Snaps into the bottom sump assembly. Essential for proper water distribution.

Replacement nozzle kit for dishwasher center spray arm. Needed when nozzles are clogged, cracked, or missing, preventing proper water distribution.

Replacement nozzle kit for dishwasher center spray arm. Needed when nozzles are clogged, cracked, or missing, preventing proper water distribution.

Secures water or drain hoses to fittings, preventing leaks and loose connections. Replace when hoses slip or drip to restore a tight seal.

Replaces cracked, split, or rodent-damaged connector hoses that route water between internal dishwasher components. Essential when the original hose leaks.

This small check ball sits inside the dishwasher's drain pump or water inlet valve and acts as a one-way valve to prevent water from flowing backward through the system. It ensures water moves in the correct direction during wash and drain cycles. Replace this part if you notice water draining back into the tub after a cycle completes, the dishwasher isn't draining properly, or water is leaking from the pump area.

Noticeable wear, cracks, or deformation on the O-ring This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Seals the rear of your dishwasher's circulation pump to prevent leaks. Replace if you notice water pooling or dripping from the motor area.

Replacement nozzle kit for dishwasher center spray arm. Needed when nozzles are clogged, cracked, or missing, preventing proper water distribution.

This is a plastic support bracket that holds the lower spray arm in place at the bottom of the dishwasher tub. It allows the spray arm to spin freely while maintaining proper water flow from the pump to the arm. Replace this support if the lower spray arm wobbles excessively, detaches during cycles, or if dishes on the bottom rack are not getting clean due to reduced water pressure.

This base is the lower cabinet support that helps keep the appliance stable and holds internal components in their correct position. Replacing a damaged base restores proper fit, alignment and reduces cabinet movement. What it does:

• Provides structural support for the appliance cabinet and mounting points
• Keeps internal components aligned and maintains correct clearance
• Helps prevent rocking, vibration and gaps at the bottom of the cabinet
• Protects lower components from contact with floor-level debris or uneven surfaces

• Disconnect power and, if applicable, water before beginning work
• Access may require removing the toe kick or lower access panels
• Keep track of mounting screws and brackets; use replacement hardware if original fasteners are corroded

This base is the lower cabinet support that helps keep the appliance stable and holds internal components in their correct position. Replacing a damaged base restores proper fit, alignment and reduces cabinet movement. What it does:

• Provides structural support for the appliance cabinet and mounting points
• Keeps internal components aligned and maintains correct clearance
• Helps prevent rocking, vibration and gaps at the bottom of the cabinet
• Protects lower components from contact with floor-level debris or uneven surfaces

• Disconnect power and, if applicable, water before beginning work
• Access may require removing the toe kick or lower access panels
• Keep track of mounting screws and brackets; use replacement hardware if original fasteners are corroded

Houses and seals the dishwasher's filter screen to trap food debris and prevent recirculation. Replace if loose, cracked, or dishes remain dirty after cycles. Confirm fit by model number before ordering.

Prevents debris from clogging your dishwasher drain. Replace if parts won't lock in place, wobble during cycles, or show wear. Twists to lock securely.

F117-20 These are normally open thermostats

F127-20

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.

Secures dishwasher thermostat to base for accurate temperature sensing. Replace if loose or broken to prevent overheating. Verify fit by model number.

Secure dishwasher components with this #8 x 5/8" mounting screw. Replace lost, stripped, or corroded screws to properly fasten panels and parts.

This replacement mounting screw secures panels and components in compatible Frigidaire appliances, helping restore stable assembly and safe operation. It's a direct-fit fastener used where the original screw has been lost or damaged. What it does

• Fastens appliance panels, brackets, and small parts to restore secure assembly
• Replaces stripped, rusted, or missing screws that can cause rattling or loose components
• Matches the OEM fit for reliable retention and alignment during normal use

• Use the correct size driver to avoid stripping the head; tighten until snug but do not overtighten
• Disconnect power or follow appliance-specific safety procedures if working near electrical components
• Inspect surrounding hardware and replace as needed

Stainless steel screw that secures the dishwasher impeller assembly. Replace if stripped, corroded, or missing to properly mount the impeller.

Replacement mounting screw for dishwasher panels and internal components. Needed when original screws are stripped, missing, or corroded during repairs.

Secure hose clamp for dishwashers and washers. Replace if worn, loose, or leaking. Verify fit with your model number before ordering.

Red

No.10 - 16 x 3/8

Replacement mounting screw for dishwashers. Secures internal components, panels, and brackets. Order when original screw is stripped, missing, or broken.

Secures the dishwasher door latch assembly to the cabinet. Replace if screw is stripped, missing, or damaged to restore secure latch installation.

Replaces missing, torn, or saturated sound-dampening insulation blanket for dishwashers. Wraps around tub to reduce noise and protect cabinetry.

Replaces missing, torn, or saturated sound-dampening insulation blanket for dishwashers. Wraps around tub to reduce noise and protect cabinetry.

This side mounting bracket kit includes the hardware needed to secure a dishwasher to the adjacent cabinetry from the sides rather than from the countertop. It is commonly used in kitchens with granite, stone, or other countertops where top-mounting screws cannot be used. Replace this kit if the original brackets are bent, broken, or missing, causing the dishwasher to shift or slide during operation.

Dishwasher won't fill with water? A faulty water level float switch prevents proper filling. This switch assembly typically takes 15 minutes to replace.

Brass nut that secures the heating element to the dishwasher tub. Replace if cracked, split, or causing leaks around the element mounting area.

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.