Mtd Gold Fastener

This muffler stud is an OEM part directly sourced from the manufacturer. The muffler stud connects the muffler to the body of the machine. Over time, stress and tension can cause these muffler studs to become loose or even fall out and become lost. Rust and corrosion due to rain and snow can also cause the muffler studs to become loose. When this happens, the studs should be replaced immediately to prevent the muffler from becoming loose or possibly coming off. If the studs are loose and the connection to the machine's engine is not secure, the machine's noise may become louder, or it could emit smoke.If the studs are loose or broken, make sure the engine has cooled down before installing new studs. Use a wrench to tighten loose muffler studs. If the studs are missing, install new ones and tighten them with the wrench. While installing the new studs, it is good to inspect the muffler for holes or damage that may reduce the performance. These muffler studs are made of high-quality steel and are sold individually. These are made to be compatible with tillers and other small engines manufactured by Cub Cadet, MTD, and Yard Machines.

This is a genuine OEM clamp sourced directly from the manufacturer. It is used in various lawn and garden machines to connect hoses to fittings. It is used to connect piping to water pumps, exhaust pipes to exhaust manifolds, and other similar applications. This connection prevents fluids or air from leaking from the hose. Clamps may be spring or screw/band clamps. Spring clamps require no tools to install and remove; however, the size must be more accurate than when using screw/band clamps. Screw/band clamps are adjustable and can be tightened or loosened. Screw clamps should be inspected periodically to ensure tightness and that the clamps have not rusted.Hose clamps are installed approximately 1/4 inch below the end of the hose. If two clamps are used, there should be 1/4 inch between the two bands. When using a screw clamp, loosen the screw with a screwdriver just enough to fit the clamp over the hose. If using a spring clamp, squeeze the clamp and hold it open. Slide the clamp over the hose and then attach the hose and clamp to the fitting. Slide the clamp into place at the joint and tighten. Do not overtighten. This brass-colored clamp is a spring clamp made of metal; it is sold as an individual unit. This clamp is compatible with many different types of pipes made by various manufacturers.

This part is a carburetor stud. A carburetor mixes fuel and air before delivering it to the engine. The carburetor stud, often called carb stud, is used to ensure a tight seal between the carburetor and the intake manifold. It is important that air and other dirt or debris do not enter the engine, and so this seal between the carburetor and the intake manifold is very important.A carburetor stud may need to be replaced if it is stripped or worn. Of course, a new carburetor stud will be needed if it is missing. If the carburetor and the intake manifold do not have a tight seal, it could be possible that new carburetor studs are needed.This part is a genuine MTD part and is an OEM part sourced directly from the manufacturer. It is sold individually. This specific carburetor stud is compatible with engines, lawnmowers, and log splitters manufactured by MTD, Yard Machines, Yard-Man, Cub Cadet, Husky, and Troy-Bilt.

This nut, or slotted nut, is a genuine MTD part. It is a replacement part for use on lawn mowers, log splitters, wood chippers, lawn tractors, and chipper shredders. It is hexagonal in shape.The uses for this nut vary greatly depending on the machine with which owners plan to use it. Generally speaking, nuts work to secure various parts of components together. Loosening and tightening most nuts can be accomplished with a wrench. Before making any repairs, be sure that the engine has completely cooled, empty the fuel tank to avoid spillage, and disconnect the spark plug or battery. Wear work gloves and other protective gear.This nut is a genuine OEM part sourced directly from the manufacturer. It is sold individually; very often, more than one nut is used on machines such as these, so be sure to check how many are needed. It is designed for compatibility with various machines made by Agway Craftsman, Cub Cadet, Duerr, MTD, Lawn Chief, OEM, Ranch King, Remington, Ryobi, White Outdoor, Yard Machines, and Yard-Man.

This replacement part is a hex screw. This part is small but important in many different kinds of equipment. Hex screws are able to work with other small parts such as washers or nuts to ensure that components are secure within the equipment.Overtightened screws might be stripped and could fall out or get stuck in place, necessitating replacement. Over time, exposure to the elements may lead to a screw becoming worn or corroded, which may cause it to break or get stuck.This is a genuine OEM replacement part manufactured by MTD. This part is sold individually.

This hex screw is a genuine MTD part, sold individually. This hex screw can be used as a replacement part in a lawn mower, snowblower, or wood chipper.The hex screw in a lawn mower, snowblower, or wood chipper might have to be replaced if it is lost, misplaced, or damaged. The screw is a small component which can easily disappear while the appliance is in operation without necessarily noticing its absence; additionally, the screw can suffer from puncturing, scraping, denting, warping, or eroding over time. If this occurs, the screw should be replaced by this genuine OEM replacement part.This OEM part is a genuine replacement that is sold individually and sourced directly from the manufacturer. This hex screw is compatible with the following outdoor appliance brands: MTD, Cub Cadet, Craftsman, Ryobi, Troy-Bilt, Yard Machines, Huskee, Montgomery Wards, Bolens, Yard Man, and MasterCut.

Lawn equipment and other machines with small gas-powered engines have fuel tanks that require a fuel tank lower grommet to keep the fuel from leaking. This grommet is located near where the fuel filter and neck meet. With use and over time, the fuel tank lower grommet may wear out or get lost. Leaking fuel is a clear indication that there is a problem with the lower fuel tank grommet. If this occurs, the part will have to be replaced to prevent further leakage and device failure.Before replacing a lower fuel tank grommet, empty the fuel tank completely. Wear gloves for protection. Push the replacement part in the hole and turn slightly to push the piece in. If necessary, use a screwdriver to push in to get a secure fit.This fuel tank lower grommet is an authentic OEM part sourced from the manufacturer. The fuel tank lower grommet is compatible with MTD, Yard Machines, Yard-Man, Cub Cadet, Husky, and Troy-Bilt machines. It can be used in various devices, including lawnmowers, log splitters, trimmers, and other engines. It is made of high-quality material and sold as an individual unit.

This is a quality clevis pin that is specifically designed for use with wood chippers and log splitters. The clevis pin is a secure and easily installed fastener that is often used in the place of rivets and bolts. As with other fasteners, the clevis pin is durable and long-lasting but wear and tear or use of the equipment can cause damage. If the clevis pin is damaged, broken, or has been lost, it will need to be replaced.When replacing a clevis pin, the tool should be powered off. Remove the spark plug wire and place the tool on a sturdy surface during the replacement process. The clevis pin may be located in various places depending on the model. Use the user's manual to determine where to get access to it. Remove the old pin and replace it with a new one before reassembling the machine.This clevis pin is sold on an individual basis. The component is designed to be compatible with lawnmowers, wood chippers, and log splitters manufactured by MasterCut, Yard-Man, MTD, Yard Machines, Ryobi, Cub Cadet, and Craftsman. This is an authentic OEM replacement part that is sourced directly from the manufacturer.

This part is a replacement valve spring retainer. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. It is intended to replace a defective valve spring retainer in outdoor power equipment.This valve spring retainer is a small part but is essential for proper and safe equipment functionality. It will need to be replaced with a genuine OEM replacement part if broken, worn, or ineffective in any way. Wear work gloves to protect the hands and check that equipment is powered off and cooled down before starting the repair process. For more accurate information on how and where to use this valve retainer spring, the appropriate owner's manual and equipment diagrams should be referred to. This valve retainer spring is a genuine OEM part made of durable metal and is sold individually. It is suitable for use with outdoor power equipment that have been manufactured by MTD, Craftsman, Troy-Bilt, and other brands.

This exhaust valve spring is a genuine MTD part, sold individually. This exhaust valve spring can be used as a replacement part in lawnmowers, snowblowers, tillers, leaf blowers, log splitters, and wood chippers. The purpose of the exhaust valve spring is to regulate the passage of materials in and out of the exhaust valve, which is maintained through spring tension.Damage to this compoennt could manifest in the form of puncturing, denting, scraping, cracking, warping, or eroding that can wear away at the spring tension and negate the functionality of the spring.This component is a genuine OEM replacement part, sourced directly from the manufacturer. It is sold individually. This exhaust valve spring is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, Troy-Bilt, Yard Machines, Huskee, Yard-Man, and MasterCut.

This part can be used to replace a worn or broken front stud to securely attach the shroud and keep it in place.Engine shrouds are critical for ensuring that air is properly circulated around the engine to keep it cool. Without an engine shroud, overheating can occur quickly and cause serious engine damage. This front stud is intended to attach the front of the engine shroud to secure it in place. This starter/shroud front stud is a genuine OEM replacement part that has been sourced directly from the manufacturer. This replacement starter/shroud front stud fits various different models of MTD, Cub Cadet, Husky, Troy-Bilt, and Yardman outdoor power equipment such as lawnmowers, log splitters, and trimmers. Please note this starter/shroud front stud is sold individually.