Parts for Electrolux E30MH65QPSA: 02 - Oven, Cabinet Parts

Replaces cracked, burned, or missing waveguide cover in your microwave. Protects the magnetron opening from food splatter and moisture damage.

Support bracket for microwaves. Mounts inside the cavity to secure components or hold parts in place. Replace if cracked, bent, or missing hardware.

Replacement support bracket for microwave ovens. Mounts inside the cavity to secure internal components. Order if your original bracket is cracked or broken.

This base plate is the lower cabinet support that restores structural stability and covers the appliance underside for a finished appearance. It helps protect internal components and maintain proper airflow under the unit. What it does:

• Provides structural support for the appliance's lower cabinet and toe area
• Secures and protects internal components located under the unit from debris and accidental contact
• Helps maintain intended airflow and clearance beneath the appliance
• Restores cosmetic appearance where the original base plate is damaged or missing

• One base plate

• Disconnect power to the appliance before starting any work
• Remove the toe grille or access panel to reach base plate mounting points
• Use basic hand tools to remove/replace screws; align plate before tightening

Microwave not heating food? A failed magnetron is the likely cause. This tube generates the microwave energy needed for cooking. Moderate DIY repair.

Microwave not heating or running weak? The capacitor stores electrical energy to power the magnetron. Common failure causes no heat or sparking issues.

Microwave not heating? This diode directs current flow to the magnetron and protects control circuits. Quick install restores heating when failed.

Captures grease and food particles from exhaust air in your microwave ventilation system. Replace when bent or saturated to restore airflow. Check fit.

Microwave won't start or is completely dead? This fuse protects against electrical overload. Requires disassembly to access. Often replace with switches.

Replaces burned out or flickering microwave interior light bulbs. Install when the bulb darkens, flickers, or stops working. Verify fit by model.

Holds the bulb and provides electrical contact for microwave illumination. Replace when heat-damaged, cracked, or bulb won't stay secure. Confirm fit.

This temperature sensor monitors internal fridge/freezer temperature so the control board can regulate cooling and defrost cycles for more consistent temperatures and food safety. What it does

• Measures compartment temperature and sends readings to the control board.
• Helps the refrigerator maintain set temperatures by enabling accurate cooling cycles.
• Supports proper defrost control when used in defrost/evaporator applications.
• A failing sensor can produce temperature fluctuation, poor cooling, or longer run times.

• One temperature sensor

• Disconnect power before servicing to avoid shock or compressor damage.
• Handle the sensor and connector gently; avoid pulling on wires.
• Verify location and routing match the original; secure sensor to prevent contact with moving parts.

Fix a microwave that won't heat properly or overheats with this thermistor. This temperature sensor monitors oven heat levels for safe operation.

This thermostat is the refrigerator temperature control that senses cabinet temperature and cycles cooling to help maintain set temperatures. It replaces a failed control to restore reliable temperature regulation. What it does:

• Senses refrigerator temperature and opens/closes the cooling circuit to maintain the set temperature
• Stops continuous compressor run when the cabinet reaches the set point
• Can cause warm or fluctuating temperatures, or a compressor that won't cycle when faulty
• Works with the control knob/selector to adjust interior temperature

• One thermostat

• Disconnect power before attempting service to avoid shock or compressor damage
• Handle the sensing bulb/capillary gently; avoid kinks or sharp bends
• Installation usually requires access to the control housing inside the cabinet and basic hand tools

Microwave won't start or stopped working during use? A failed thermostat often causes complete shutdown. This temperature switch is replaceable DIY.

Fix a microwave fan that won't shut off or overheating issues with this thermostat. Monitors temperature to prevent damage. Moderate DIY repair.

The Thermal Cut Off is an OEM part for Frigidaire microwaves. It is located inside the microwave cavity or near the magnetron tube. It is designed to monitor the temperature and interrupt the electrical current if it exceeds a safe limit. This prevents the microwave from overheating and potentially causing damage or hazards.

Causes of a faulty or damaged thermal cut off can include regular wear and tear, electrical malfunctions, or overheating due to excessive use or blocked airflow. These factors can result in issues such as the microwave not heating food properly, frequent shutdowns during operation, or complete failure to function.

Symptoms of a bad thermal cut off may include:

• The microwave not generating heat
• The microwave turning off abruptly during operation
• The microwave not starting or experiencing intermittent operation

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Fix an air conditioner that won't start or runs poorly. This compressor start/run capacitor restores motor operation and improves cooling performance.

This evaporator fan assembly circulates cold air through the freezer and refrigerator compartments to help maintain even temperatures and proper cooling. Replaces a worn or failed fan to restore airflow. What it does:

• Spins to move cold air across the evaporator coil and into the appliance interior
• Commonly linked to symptoms like unusual noise, weak cooling, or no airflow in compartments
• Helps prevent frost build-up by maintaining steady airflow over the coil
• Works with the appliance's evaporator motor circuit and fan housing

• One evaporator fan assembly

• Disconnect power to the appliance before beginning any work
• Access may require removing interior panels or the evaporator cover; follow your model's service instructions
• Handle the fan blades and motor carefully to avoid damage; avoid contact with sharp sheet metal and edges
• Test the fan operation after reassembly and restore all panels and fasteners

Replacement panel for microwave ovens. Restores the exterior appearance when the original panel becomes cracked, dented, discolored, or damaged.

The Latch Hook is an OEM replacement part for Frigidaire microwaves. It is an internal component that helps securely latch and lock the microwave door during operation. The latch hook works with the door handle mechanism to ensure the door is properly fastened to prevent leaks of microwave energy and for safety. 

Causes of a bad latch hook can include wear and tear over time, damage from repeated use of the door latch, or issues with the latch hook spring or connecting components. 

Symptoms of a bad latch hook include:

• The microwave door not closing or latching securely  
• Difficulty closing or popping open the door during a cycle
• Leaks of microwave energy from around the door seals
• Error codes related to door-latching problems

This OEM Frigidaire replacement part is also compatible with Electrolux, Westinghouse, and Kelvinator microwaves. 

This door release lever connects the push-button to the latch assembly inside the microwave. Replacing a worn lever restores smooth, reliable door opening so the button works on the first press.

• Transfers motion from the door-open button to the latch hooks to release the door
• Helps resolve a door that won't open when the button is pressed
• Addresses a button that feels loose, sticks, or lacks resistance
• Replaces a cracked or broken lever causing intermittent door operation

• Unplug the microwave and discharge the high-voltage capacitor before servicing
• Remove the grille and control panel to access the interlock/latch area
• Note spring and pivot orientation and transfer any reusable hardware
• Test door release action before completing reassembly

Microwave tripping breaker or won't start? A faulty door switch is often the cause. This safety switch detects door position. Moderate DIY repair.

Microwave tripping breaker or won't start? A faulty door switch is often the cause. This safety switch ensures your microwave only runs when the door is closed.

Mounting bracket for microwave installation. Secures the unit to wall or cabinet. Replace if bent, cracked, or missing for proper support and alignment.

This water filter cartridge replaces the refrigerator's inline/slot-style filter to help reduce taste and odor from your drinking and ice water. It restores filtered water flow and helps keep dispensed water clear and fresh. What it does:

• Removes common impurities that affect water taste and odor
• Helps reduce particulates and sediment in dispensed water
• Restores proper filtered water flow when a clogged/expired filter causes slow flow
• Supports clearer, better-tasting ice and drinking water

• One water filter cartridge

• Turn off the water supply and dispense any remaining water before removing the old filter
• Follow the refrigerator manufacturer's push/pull or twist-release procedure for removal and installation
• After installing, flush several quarts of water through the dispenser to clear air and initial carbon fines
• Replace per the refrigerator manufacturer's recommended schedule or when filter performance declines

Mounting bracket kit for microwaves. Secures appliance components with brackets and hardware. Replace if brackets are broken, bent, or missing.

Captures grease and particles during cooking to prevent buildup in your microwave's ventilation system. Replace when clogged to maintain airflow. Verify fit.

Mounting bracket for microwave ovens. Installs to secure the microwave chassis to the wall or cabinet. Replace if bent, cracked, or missing.

This genuine connector restores a secure electrical link in your appliance's wiring harness to help re-establish reliable power or signal transfer. It replaces a damaged or corroded connector for safer, more consistent operation. What it does

• Joins wiring within the appliance harness to maintain electrical continuity
• Restores power or control signals to the attached component when a faulty connector causes loss of function
• Helps prevent intermittent connections, arcing, and heat build-up from loose or corroded terminals
• Works where a direct plug-in or crimp-style connection is required by the OEM

• One connector as shown

• Always disconnect power (unplug or shut off breaker) before inspecting or replacing electrical parts
• Verify connector orientation and terminal type match the wiring harness before installation
• Use proper crimping tools or OEM-recommended connector methods; avoid twisting or soldering unless specified by the manufacturer
• If wiring is damaged, repair or replace the harness section per OEM guidance

Microwave won't heat or turntable not spinning? A worn drive belt may be the cause. This replacement belt connects the motor to the turntable mechanism.

If your microwave turntable won't rotate or makes grinding noises, this pulley connects the motor to the turntable tray. Easy 15-minute DIY fix.

This Turntable Motor is an OEM part for Frigidaire microwaves. Responsible for the rotation of the microwave's turntable, which ensures even cooking and heating of food. This motor ensures that the turntable operates smoothly and reliably, maintaining the efficiency of your microwave.

A malfunctioning motor can lead to uneven heating or cooking of food, as the turntable is integral to the microwave's ability to distribute heat uniformly.

Symptoms of a faulty turntable motor include:

• The turntable does not rotate when the microwave is in use.
• Intermittent or erratic movement of the turntable.
• Unusual noises coming from the turntable area during operation.
• Food is unevenly cooked or heated, indicating inconsistent turntable motion.
• The microwave operates normally except for the turntable function.

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.
 

Microwave turntable not rotating? This motor drives the turntable rotation. Common fix for plates that won't spin. Takes 15-30 minutes to install.

Replaces broken or melted microwave turntable coupler shaft. Connects motor to rotating tray. Essential when coupler is cracked, worn, or missing.

Glass tray not rotating or uneven heating? This rotating ring supports and spins the turntable for consistent cooking. Simple snap-in installation.

Replacement glass turntable tray for microwaves. Installs as the rotating plate where food sits during cooking. Replace if cracked, chipped, or broken.

This fan blade mounts to the refrigerator fan motor to move air through the appliance for proper cooling and temperature circulation. Replaces a worn or damaged blade to restore airflow and improve cooling efficiency. What it does:

• Spins on the fan motor to circulate air across the evaporator or condenser coils
• Restores proper airflow when a cracked or broken blade causes reduced cooling
• Helps stop vibration or rattling caused by bent or missing blades
• Can reduce motor strain from an imbalanced or damaged blade

• Disconnect power to the appliance before starting any repair
• Remove access panels and fan shroud to reach the blade; keep track of mounting hardware
• Replace carefully to avoid bending the blade; ensure correct orientation on the motor shaft

Microwave not venting or fan not spinning? This fan motor replacement restores proper airflow and ventilation. Direct fit for multiple microwave models.

Deflector for microwaves and microwave hood combos. Directs airflow inside the cavity. Replace if cracked, broken, or missing to restore proper operation.

Decorative front grill that covers the ventilation area on your microwave. Replace if cracked, broken, or discolored to restore appearance and airflow.

Protective cover panel for microwave ovens. Replaces damaged, cracked, or missing covers. Restores clean appearance and proper housing protection.

Microwave won't rotate evenly or makes grinding noises? This rotating shaft restores smooth turntable motion when worn or stripped. Simple DIY fix.

This fan blade circulates cold air across the evaporator to help maintain even refrigerator/freezer temperatures and efficient cooling. Replacing a damaged or warped blade restores proper airflow and reduces unusual noise. What it does:

• Moves air across the evaporator coil so the appliance can cool evenly
• Helps prevent hot spots and frost buildup caused by poor airflow
• Can cause loud noise, reduced cooling, or a warm compartment when worn or broken
• Works with the evaporator/fan motor assembly to keep temperatures stable

• One fan blade

• Disconnect power before accessing evaporator compartment or fan assembly
• Handle blade carefully to avoid bending the fins; a bent blade causes vibration and noise
• May require removing evaporator cover or fan shroud; keep track of any screws or clips
• If motor is noisy or blade clearance is tight, inspect/replace motor or mounting hardware as needed

Replacement cover panel for your microwave. Installs on the exterior housing. Order a new cover if yours is cracked, broken, or missing.

Controls airflow through your microwave's ventilation system. Installs at exhaust opening to prevent air backflow. Replace if cracked, missing, or damaged.

The Damper is an OEM part for Frigidaire microwaves. This part regulates airflow within the microwave, ensuring that steam and odors are properly vented out during cooking.

Causes of a bad damper can include wear and tear over time, buildup of grease and debris, or damage from high temperatures.  

Symptoms of a bad Damper include:

• Poor ventilation during cooking, leading to lingering odors and steam
• The microwave overheating or not ventilating properly
• Unusual noises coming from the damper area
• The damper not opening or closing as it should

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This cabinet is the main outer housing that supports and encloses the refrigerator's internal components, restoring the unit's structure and appearance. It provides a secure frame for doors, panels, and internal assemblies. What it does:

• Replaces a damaged or dented outer refrigerator housing to restore fit and finish
• Supports door hinges, trim, and internal panels for proper alignment
• Helps protect internal insulation, wiring, and cooling components from damage
• Addresses symptoms like visible exterior damage, misaligned doors, or rattling from a loose enclosure

• One cabinet outer housing as shown

• Disconnect power and empty unit before beginning work to avoid injury or damage
• Use proper lifting assistance; cabinet can be heavy and awkward to handle
• Retain all mounting hardware unless a replacement is explicitly included

Interior shield for microwaves and microwave/hood combos. Replaces cracked, damaged, or missing shields that protect internal components.

Rear wall mounting bracket that securely attaches your microwave to the wall or cabinetry. Replace if your original bracket is missing, cracked, or damaged.

This mounting nut kit secures a threaded connection or component inside your appliance, keeping it tight and stable during operation. Replacing a worn or stripped nut restores a solid hold and helps prevent leaks, rattling, and poor performance. What it does:

• Fastens a component or fitting to its mating surface, maintaining proper alignment
• Restores grip when original threads are stripped, cracked, or worn
• Helps prevent vibration-related loosening during cycles
• Can resolve symptoms such as a loose/wobbly assembly, rattling noises, seepage at the joint, or visible thread damage

• One mounting nut kit

• Disconnect power; shut off water supply if the joint carries water
• Support the mating component while installing to avoid strain on plastic parts
• Start threads by hand to prevent cross-threading; tighten only until snug—do not overtighten
• Inspect any related gasket/O-ring and replace if worn or damaged

Assortment of fasteners for securing microwave panels and components. Use to replace missing, stripped, or corroded screws that hold parts in place.