Parts for Jenn-Air S166B-C: 03 - Oven Parts

Oven not heating or baking unevenly? A faulty lower bake element is often the cause. This bottom heating element restores consistent temperature. 10-minute DIY fix.

Oven won't heat or bake properly? A faulty bake element is often the cause. This heating element replacement takes about 5 minutes with basic tools.

Replacement 10-32 machine screw for securing panels, brackets, and internal components. Ideal for replacing missing, stripped, or damaged hardware.

Broiler not heating or browning food properly? This upper broil element restores intense top heat for even broiling. Takes 15-20 minutes to replace.

Broil element not heating or glowing? This upper heating element restores high-heat broiling. Common DIY fix, typically installs in under 10 minutes.

This part has been discontinued by the manufacturer and is no longer available.

This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.

• Fastens panels, brackets, covers, or internal parts to the chassis or frame
• Helps maintain alignment and support, reducing rattle, vibration, or looseness
• Replaces missing or damaged screws that have backed out, broken, or stripped
• Restores secure mounting after service when original hardware is lost

• Disconnect power; shut off water or gas supplies before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Match length and thread to the original location; do not substitute with longer hardware
• Tighten snugly; do not overtighten into plastic or thin metal

The Whirlpool screw is an OEM replacement part responsible for securing various components or parts on different types of Whirlpool appliances. The screw is designed to provide a secure and reliable fastening connection, ensuring that different parts of the appliance stay in place. It is commonly used in different locations within the appliance, such as the cabinet, panels, or other structural elements.

This part fixes the following symptoms:

• Loose or wobbly components within the appliance
• Panels or parts that are not securely attached
• Rattling or unusual noises due to loose parts
• Damaged or missing screw

The Whirlpool screw can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

Color: Stainless steel

This part has been discontinued by the manufacturer and is no longer available.

Replacement broiler pan set for ovens. Includes pan and insert to catch drippings during broiling. Order if your original is missing, warped, or damaged.

Replacement broiler pan set for ovens. Includes pan and insert to catch drippings during broiling. Order if your original is missing, warped, or damaged.

This part has been discontinued and is no longer available.

This heating element warms the wash and rinse water and helps dry dishes at the end of the cycle. Replacing a failed element restores proper temperatures, cleaning performance, and drying so cycles finish as expected.

• Heats water to target temperature during wash and rinse phases
• Aids in drying by radiating heat into the tub at cycle end
• Controlled by the dishwasher's electronics to maintain proper heat
• Common symptoms of failure: water stays cool, poor drying, extended cycle times, or a visibly broken/burned element

• Disconnect power at the breaker and allow the dishwasher to cool before servicing
• Access is typically from inside the tub and/or beneath the unit after removing the toe panel
• Note wire positions, disconnect leads, remove retaining hardware, and carefully extract/install the element without bending it
• Ensure seals are correctly seated and tightened evenly; run a short cycle to check for leaks and heat

This part has been discontinued by the manufacturer and is no longer available.

This screw-and-washer fastener is a factory-size 8-18 x 5/16 hardware piece used to secure appliance panels and components. Replace stripped, rusty, or missing hardware to restore a tight, rattle-free fit and proper alignment. What it does:

• Fastens sheet-metal panels, brackets, and small components in the appliance cabinet
• Replaces lost, stripped, or corroded screws to maintain secure mounting
• Helps reduce vibration, buzzing, or rattling from loose parts
• Useful when the original hardware is missing or no longer holds securely

• Includes 1 screw-and-washer fastener (8-18 x 5/16)

• Disconnect power; shut off gas and water supplies if applicable
• Match the fastener to the original location; sizes can vary by application
• Start threads by hand to avoid cross-threading; use an appropriately sized driver
• Tighten snugly without overtightening to prevent stripping sheet metal

Secures panels, brackets, and trim on ranges and ovens. Replace when stripped, missing, or corroded to restore stable mounting and stop rattling parts.