Kenmore Dryer 110.94832201 (11094832201, 110 94832201) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3392519
Stop dryer downtime in its tracks — install the Whirlpool WP3392519 OEM Thermal Fuse in minutes.
OEM Quality Fast 1–2 Day Shipping* Free Tech Help
Why choose this fuse?
- Guaranteed OEM: built by Whirlpool to Whirlpool specs — no risky aftermarket clones.
- Broad compatibility: works with Whirlpool, Kenmore, Maytag, KitchenAid, Roper & more.
- Quick delivery: over 94 % of APP orders arrive in 2 days or less.
Fixes these common dryer problems
| Problem |
How the fuse is involved |
| Dryer won’t start |
Blown fuse interrupts motor circuit |
| No heat / not enough heat |
Heater circuit disabled for safety |
| Cycle ends early |
Over-temp trip stops cycle |
| Control panel dead |
Power to controls interrupted |
4-step DIY installation (≈10 min)
- Unplug dryer and remove rear panel.
- Locate thermal fuse on blower housing.
- Transfer wires; secure new fuse with ¼-inch nut-driver.
- Clean the vent & lint path before testing to prevent repeat failure.
*Video tutorial below.
Ready to get heat back?
Click Add to Cart now & enjoy industry-leading 1–2 day delivery on
This part fixes the following symptoms
-
Won't start
-
Timer will not advance
-
No heat or not enough heat
-
Touchpad does not respond
See more...
Do-It-Yourself Stories from Customers like You
No heat Dennis G. • Kearny , NJ • January 14, 2017
I did the recommended checks of parts as listed on the website. I would recommend as one other person did but I did not listen the first time and that is to check all the parts don't stop at the first part you find bad. As I had to make two orders paying shipping twice because I thought I found a bad part when testing the igniter but the thermal fuse was also bad and since in a different part of the machine I did not take the time to check it, bad mistake.
Also one tool mentioned in the video...
Read more
More
$17.95
- Compare At:
-
$21.54
- You Save:
-
$3.59
Genuine Whirlpool part
By: Whirlpool
Part Number: 4392067
Silence the squeaks and keep laundry moving - upgrade your dryer with the Whirlpool 4392067 OEM Repair Kit.
Why choose this kit?
- All-in-one fix: OEM belt 661570V, 4 heavy-duty rollers WPW10314173, idler pulley 279640, tri-rings & washer - everything factory-fresh in one box.
- Wide compatibility: Fits 27" Whirlpool-family dryers—Cabrio, Duet, Bravos XL, Thin Twin, Kenmore 110-series, Maytag, Roper, Estate & more.
- Pro-grade durability: Roller bearings & reinforced belt deliver whisper-quiet tumbling and longer service life.
Fixes these common dryer problems
| Problem |
How the kit solves it |
| Loud squeaking / thumping |
Worn rollers or idler pulley replaced |
| Drum won’t turn |
Broken or stretched belt replaced |
| Extended dry times |
Restores proper drum speed & airflow |
| Burning-rubber smell |
New belt & pulley eliminate slippage |
DIY install in about 45 minutes
- Unplug dryer and remove front panel.
- Lift drum to release belt; remove old rollers & idler.
- Install new rollers, pulley & belt following the routing diagram.
- Re-assemble, run test cycle - enjoy quiet, smooth tumbling.
Note: Belt may differ from your dryer's model—Double-check compatibility before purchase.
Do-It-Yourself Stories from Customers like You
Very loud squeak inside whirlpool duet sport dryer model wed8300sw0 Steve W. • Boone , NC • September 27, 2014
Our Whirlpool Duet Sport Dryer, 6.7 cu. ft, Model WED8300SW0, bought new 8 years ago (2006), developed a VERY loud squeaking noise inside the dryer. Removing the top panel did not isolate the problem. I researched the problem and through the videos appearing on Appliance Parts Pros (APP) website and a few others, determined that the problem was either the drum belt, one or more of the 4 drum support rollers, or idler pulley or any combination of these. I ordered the kit to allow for...
Read more
More
$37.65
- Compare At:
-
$47.83
- You Save:
-
$10.18
Genuine Whirlpool part
By: Whirlpool
Part Number: 279834
The Dryer Gas Valve Coil Kit is an OEM replacement part for Whirlpool dryers, as well as Kenmore and Samsung dryers. It is a set of coils that control the flow of gas fuel to the burner. The gas valve regulates the precise amount of gas needed to properly combust and generate heat for drying clothes.
Causes of a bad gas valve coil can be wear and tear from regular use, lime or mineral buildup on the coils over time, or physical damage to the coils.
Symptoms of a bad gas valve coil kit include:
- Inconsistent or incomplete drying
- Slow or intermittent drying
- Burning smell from the gas dryer
- Improper burner ignition or non-ignition
This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
This part fixes the following symptoms
-
Timer will not advance
-
No heat or not enough heat
-
Shuts off too soon
-
Takes too long to dry
See more...
Do-It-Yourself Stories from Customers like You
Flame to dry clothes would go out after about a minute and wouldn't reignite Wendell M. • Brown Deer , WI • June 19, 2014
I'm starting with a quick background on my dryer. About 18 months ago the belt on the dryer started slipping and squealing. I had a can of belt dressing spray so I popped the top open and sprayed the belt. It actually worked for about a year before it started squealing again. For the next 6 months I had to spray it more and more often. Then the clothes stopped drying. Obviously, at this point, I had to get off my lazy ass and fix the dryer. Searched my dryer's model number on the internet and...
Read more
More
$27.21
- Compare At:
-
$32.11
- You Save:
-
$4.90
Genuine Whirlpool part
By: Whirlpool
Part Number: W10837240
The Idler Pulley Assembly is an OEM part compatible with Whirlpool dryers. It is a crucial component of the dryer's drive system, responsible for maintaining proper tension and alignment of the belt that drives the dryer drum. Measuring 5.5 x 3.5 x 3 inches, this idler pulley assembly typically consists of a pulley mounted on a bracket or arm, which can pivot or move to apply the necessary tension to the belt.
Symptoms of a faulty Idler Pulley Assembly include:
- Loud squeaking or grinding noises during operation
- The dryer drum not spinning or rotating properly
- Excessive vibrations or shaking during the drying cycle
- Visible wear or damage to the belt or pulley components
Causes of a bad idler pulley assembly can include bearing failure, physical damage from foreign objects, or normal wear and tear over time.
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dryer models.
Do-It-Yourself Stories from Customers like You
The idler pulley was squeaking Bob C. • Fall River , MA • June 12, 2014
I bought the new arm assembly because after a few times of going in through the front of the machine and reaching in the back under the drum I could get to the pulley, so I took it off of the arm and lubed it and then replaced it back inside, put the belt back on and it was good for a week or so , then started squeaking again. So after doing this about 6 times I got the impression that is was the wheel and shaft on the arm were worn out causing the wheel to wobble and wear the arm.
I then...
Read more
More
$26.95
- Compare At:
-
$32.34
- You Save:
-
$5.39
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8577274
The Thermistor is an OEM part for Whirlpool brand dryers. It is a temperature-sensing resistor that monitors air temperature changes during the drying cycle. The thermistor provides feedback to the control board on heating element performance and internal air condition.
Symptoms of a failed thermistor include:
- Inaccurate temperature readings and selections
- Improper or incomplete drying
- Safety issues from overheating due to lack of feedback
- Error codes displayed on the control panel
Causes can be related to normal wear and environmental exposure over time. Failure prevents the dryer from achieving optimal drying conditions.
This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
This part fixes the following symptoms
-
Too hot
-
Shuts off too soon
See more...
Do-It-Yourself Stories from Customers like You
First longer to dry then no heat in dryer Bobbie M. • King George , VA • October 06, 2017
I am not an electrician, just a housewife with limited funds and a desire to DIY. I used the provided videos for knowing how to replace everything except the heating element which I just guessed based on other reviews and seeing how the other parts worked. Our dryer is 11 years old Whirlpool Gold HE and I have only ever cleaned the lint tray. My husband replaced the belt about five years ago and he did clean out the inside of the dryer.
Started by ordering a thermal fuse because it was...
Read more
More
$35.58
- Compare At:
-
$41.98
- You Save:
-
$6.40
Genuine Whirlpool part
By: Whirlpool
Part Number: 279311
The Igniter Kit and Bracket is an OEM replacement part for Whirlpool dryers. It is a kit that includes the igniter and bracket assembly, which work together to ignite the gas or electric heating element.
Causes of a bad igniter and bracket can include failure due to prolonged or repeated use, damage from impact or mishandling, or failure of integrated electronic components.
Symptoms of a bad igniter and bracket include:
- The dryer not heating or heating intermittently
- Repeated trips of the thermal fuse
- Smell of gas indicating improper ignition
- Visible damage or cracks in the igniter or bracket
This Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.
This part fixes the following symptoms
-
No heat or not enough heat
-
Takes too long to dry
See more...
Do-It-Yourself Stories from Customers like You
11 year old kenmore elite gas drye stopped working initial diagnosis: burner would light but would shut off in 3 or 4 minutes Jay W. • Dallas , TX • April 05, 2015
I used Fixya as an initial source describing my problem. I got two responses which were very helpful. One that the "coils" were probably the problem. Two, that the problem could be the thermostat or a thermistor in the dryer. I verified that AC was coming from the timing control, that both the two terminal and three terminal coils,the igniter and shut off thermostat all had continuity. I then applied AC directly to the coils: the two terminal coil ""clanked" and I interpreted that as the coil...
Read more
More
$35.58
- Compare At:
-
$42.70
- You Save:
-
$7.12
Genuine Whirlpool part
By: Whirlpool
Part Number: 661570V
The Drive Belt is an OEM replacement part for Whirlpool dryers. This essential component is responsible for transferring power from the dryer's motor to the drum, allowing it to spin and tumble the clothes during the drying cycle.
Symptoms of needing to replace the drive belt include:
- The dryer drum not spinning or rotating
- Loud squeaking or grinding noises during the drying cycle
- Excessive vibration or shaking from the dryer
- Clothes taking longer to dry or remaining damp
Causes of a faulty drive belt can include normal wear and tear over time, exposure to excessive heat or lint buildup, or physical damage due to impact or mishandling.
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dryer models.
Do-It-Yourself Stories from Customers like You
I had no error code, it is just that when you press start you would hear a click and no actions. Nicholas M. • Miami , FL • June 12, 2020
It was the day of my birthday June 6th when my wife came to me to tell me that the dryer was not working. Immediately I started to look for a new dryer from Best Buy and the rest. Then I said It would be better if I waited for 4th of July at which time I could find a better deal. This is when I decided to take it apart to see what was wrong. Initially, I thought of the belt that could be broken and I rotated the drum by hand and I heard a noise of the belt at times falling on the drum. I was...
Read more
More
$39.29
- Compare At:
-
$47.15
- You Save:
-
$7.86
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10314173
The Drum Support Roller is an OEM replacement part for Whirlpool dryers. It plays a crucial role in supporting and facilitating the smooth rotation of the dryer drum during the drying cycle.
Symptoms of needing to replace the drum support roller include:
- Excessive noise or grinding sounds coming from the dryer drum
- Difficulty in rotating the drum or drum not turning at all
- Visible signs of wear, cracking, or damage on the existing roller(s)
- Increased vibrations or shaking during the drying cycle
Causes of a faulty drum support roller can include normal wear and tear over time, exposure to excessive heat or lint buildup, or physical damage due to impact or overloading.
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dryer models.
Do-It-Yourself Stories from Customers like You
The dryer drum would barely turn. James R. • Minden , NV • December 09, 2022
I watched videos on the disassembly of my dryer model, and got the model number hiding on the upper dryer door jamb. After calling AppliancePartsPros.com for help, then ordered parts with the help of APP. It took almost a full day to disassemble the dryer I have, as it is a little more complicated than some models, and I went very slowly on purpose to not lose screws, or break plastic parts.
Getting the wiring harness apart was the hardest thing to do, as the screwdriver shown in the video...
Read more
More
$18.95
- Compare At:
-
$22.36
- You Save:
-
$3.41
Genuine Whirlpool part
By: Whirlpool
Part Number: 279570
The Door Latch Kit is an OEM replacement part for Whirlpool washers. This component is responsible for securely locking the washer door during the wash cycle, preventing it from opening unexpectedly and ensuring a safe and efficient operation.
Symptoms of needing to replace the door latch kit include:
- Difficulty in closing or latching the washer door
- Door opening unexpectedly during the wash cycle
- Leaks or water seeping due to an improper door seal
- Excessive wear or damage to the latch components
Causes of a faulty door latch kit can include normal wear and tear over time, physical damage due to impact or mishandling, or issues with the door alignment or strike plate.
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washer models.
This part fixes the following symptoms
-
Door won't close
-
Shuts off too soon
-
Doesn't shut off
-
Takes too long to dry
See more...
Do-It-Yourself Stories from Customers like You
Dryer door latch worn out Kathy M. • San Diego , CA • February 22, 2015
When I looked up the part number there was a handy video that popped up. I watched the video and thought "how easy!" so, I ordered that part and waited. The next day, I thought I better start to take the door off of my dryer (because that's what the video instructed, and I wanted a head start) so as I was going into the garage to get my tools, my son came in with a small package. It was the part. That came, to quote another customer, "Crazy Fast!" All the way from Kentucky to California! ...
Read more
More
$6.95
- Compare At:
-
$13.85
- You Save:
-
$6.90
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3387223
The Moisture Sensor Bar is an OEM replacement part for Whirlpool dryers. It is a component located inside the dryer drum that senses the moisture level of clothes during tumble drying cycles. The moisture sensor bar utilizes sensors or probes to gauge how dry clothes are getting and signals the dryer to shut off once clothes reach the desired dryness level selected by the user.
Symptoms of a bad moisture sensor bar include:
- Dryer failing to shut off automatically at the end of cycles, leaving clothes over-dried
- Cycles taking excessively long to complete
- Dryer not sensing moisture levels properly to allow automatic ending of cycles
Causes of a faulty moisture sensor bar are usually due to normal wear and tear over time. Dust or lint buildup can also affect its ability to provide accurate readings.
This OEM replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
First longer to dry then no heat in dryer Bobbie M. • King George , VA • October 06, 2017
I am not an electrician, just a housewife with limited funds and a desire to DIY. I used the provided videos for knowing how to replace everything except the heating element which I just guessed based on other reviews and seeing how the other parts worked. Our dryer is 11 years old Whirlpool Gold HE and I have only ever cleaned the lint tray. My husband replaced the belt about five years ago and he did clean out the inside of the dryer.
Started by ordering a thermal fuse because it was...
Read more
More
$9.95
- Compare At:
-
$11.74
- You Save:
-
$1.79
Genuine Whirlpool part
By: Whirlpool
Part Number: 279640
The Idler Pulley is an OEM replacement part for Whirlpool dryers. This essential component plays a crucial role in the drum drive system, helping to guide and maintain proper tension on the dryer belt.
Causes of a faulty idler pulley in a dryer can include normal wear and tear over time, improper belt tensioning leading to bearing failure, or physical damage from impact or debris buildup.
Symptoms of needing to replace the idler pulley include:
- Squeaking or grinding noises from the driveability area
- The dryer drum not spinning or rotating properly
- Excessive vibration or shaking during the dryer cycle
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dryer models.
Do-It-Yourself Stories from Customers like You
I had no error code, it is just that when you press start you would hear a click and no actions. Nicholas M. • Miami , FL • June 12, 2020
It was the day of my birthday June 6th when my wife came to me to tell me that the dryer was not working. Immediately I started to look for a new dryer from Best Buy and the rest. Then I said It would be better if I waited for 4th of July at which time I could find a better deal. This is when I decided to take it apart to see what was wrong. Initially, I thought of the belt that could be broken and I rotated the drum by hand and I heard a noise of the belt at times falling on the drum. I was...
Read more
More
$25.95
- Compare At:
-
$31.14
- You Save:
-
$5.19
Genuine Whirlpool part
By: Whirlpool
Part Number: WP338906
The Flame Sensor is an OEM replacement part for Whirlpool gas dryers. This component plays a critical safety role by monitoring the presence of the gas burner flame during the drying cycle.
Causes of needing to replace the flame sensor can include normal wear and tear over extended use, exposure to high temperatures or corrosion, or physical damage to the sensor itself.
Symptoms that may indicate a faulty flame sensor include:
- The dryer not heating or producing heat properly
- Error codes related to the gas system or ignition failure
- The dryer shutting off unexpectedly during cycles
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore gas dryer models.
This part fixes the following symptoms
-
Shuts off too soon
-
No heat or not enough heat
-
Takes too long to dry
See more...
Do-It-Yourself Stories from Customers like You
11 year old kenmore elite gas drye stopped working initial diagnosis: burner would light but would shut off in 3 or 4 minutes Jay W. • Dallas , TX • April 05, 2015
I used Fixya as an initial source describing my problem. I got two responses which were very helpful. One that the "coils" were probably the problem. Two, that the problem could be the thermostat or a thermistor in the dryer. I verified that AC was coming from the timing control, that both the two terminal and three terminal coils,the igniter and shut off thermostat all had continuity. I then applied AC directly to the coils: the two terminal coil ""clanked" and I interpreted that as the coil...
Read more
More
$34.95
- Compare At:
-
$41.59
- You Save:
-
$6.64
Genuine Whirlpool part
By: Whirlpool
Part Number: 280114
The Dryer Drum Felt Seal is an OEM replacement part for Whirlpool electric dryers. Located inside the spinning dryer drum, it lines the perimeter and protects the interior surface from abrasions. This seal measures approximately 82 inches in length.
Symptoms of a bad dryer drum felt seal include:
- Scratches or scuff marks visible on the inside of the drum
- Visible wear patterns or thinning of the felt material
- Premature rusting or corrosion of the steel drum
- Chipped or delaminated areas exposing bare steel
Causes of failure can include normal wear from friction generated during high-speed spins. Mineral deposits and grit trapped between the seal and drum may accelerate wear over extended use as well.
This OEM part is also compatible with brands like Maytag, Amana and Kenmore.
Do-It-Yourself Stories from Customers like You
Dryer squealed when first started & my wife noticed a piece of clothing getting caught in front seal Dale M. • Peshtigo , WI • January 02, 2018
Maytag Gas Dryer Model: MGDE300VW1
I had previous experience with repairing my dryers, but this was a first for this model. Instructional videos very helpful. Ordered necessary parts and they were delivered with-in two days. Wow!
Squeak found to be coming from idler pulley roller which no longer turned freely . The four other cabinet rollers had signs of wear. Dryer belt had frayed edges and a couple of burn spots in the belt from the motor turning before the drum did. Cleaned up all shafts...
Read more
More
$42.95
- Compare At:
-
$51.11
- You Save:
-
$8.16
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10512946
The Drum Support Wheel Retainer is an OEM part for Whirlpool dryers. This part secures the drum support wheels in place, ensuring that the dryer drum rotates smoothly and quietly during operation. The retainer is designed to fit precisely, preventing the support wheels from loosening or wobbling, which can lead to inefficient drying and increased wear on other components.
Over time, retainers can wear out or become damaged, potentially leading to a loose drum support wheel. This can cause the dryer to operate noisily, vibrate excessively, or even damage the drum itself if not addressed promptly.
Symptoms of a bad Drum Support Wheel Retainer include:
- Unusual noises, such as squeaking or thumping, coming from the dryer
- Excessive vibration during operation
- The dryer drum may feel unstable or wobble when turned by hand
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Do-It-Yourself Stories from Customers like You
My whirlpool duet dryer started to squeal and rumble when the dryer was on Diana K. • Phoenix , AZ • September 20, 2014
I did a little research and found out that the dryer drum rollers needed to be replaced. I decided that since I would be replacing the 4 drum rollers that I should replace the belt and the belt drive pulley. This was a simple project thanks to YouTube. I used one of appliancepartspor videos to st me through the repair. Now I have a dryer that does not squeal like a pig!
Read more
More
$10.95
- Compare At:
-
$12.92
- You Save:
-
$1.97
Genuine Whirlpool part
By: Whirlpool
Part Number: W10120998
The Dryer Lint Filter is an OEM replacement part for Whirlpool electric dryers. This essential screen traps lint and debris released from tumbling clothes. Consistent filtration is key for safety and performance. This filter measures approximately 12 1/2 inches wide and 10 1/2 inches deep.
Causes of a clogged lint filter can be an accumulation of lint from regular drying cycles plugging ventilation holes. Neglecting filter cleaning allows fluff to build up rapidly.
Symptoms of a dirty lint filter include:
- Extended drying times as airflow is restricted
- Overheating problems or melted slots in the filter housing
- Risk of dryer or clothing fires from unvented lint buildup
This OEM replacement part is also compatible with Kenmore and Maytag models too, it removes the fire hazard of neglected cleaning.
Do-It-Yourself Stories from Customers like You
Dryer lint filter was so jammed with lint that it might have started a fire! Judith S. • Port St. Lucie , FL • April 03, 2015
My fiance was involved in a very nasty divorce where a very biased female judge forced him from his home for 14 months before he could take up residency again. He brought me back with him and I witnessed the grotesque damages she intentionally inflicted on his property. His washer and dryer are very expensive and high-end, as is the home and all his contents. One of the many damages she caused was that she had not cleaned the dryer lint filter in 14 months and the lint was a thick carpet which...
Read more
More
$42.95
- Compare At:
-
$51.69
- You Save:
-
$8.74
Genuine Whirlpool part
By: Whirlpool
Part Number: W11086603
The Lint Screen Grille is an OEM part for Whirlpool dryers. It works with the lint screen to capture and collect lint during the drying cycle, preventing it from clogging the vent and ensuring proper airflow.
A bad dryer lint screen grille can be caused by regular wear and tear, accumulation of debris, or accidental damage. If the grille becomes cracked, broken, or warped, it can lead to lint escaping from the lint screen or obstructed airflow.
Symptoms of a bad dryer lint screen grille include:
- Lint escaping from the lint screen area.
- Reduced drying efficiency or longer drying times.
- Visible damage or warping of the grille.
- Excessive lint buildup in the venting system.
This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
Do-It-Yourself Stories from Customers like You
The lint catch was broken Misti P. • Spokane , WA • January 18, 2019
This was actually one of the easiest fixes I’ve done. All that was required was to remove 3 screws to remove the broken part. I used a pair of pliers to remove the moisture sensors from the broken part to the new one.
Read more
More
$28.22
- Compare At:
-
$33.30
- You Save:
-
$5.08