Kenmore Dryer 417.94132000 (41794132000, 417 94132000) Parts

Disassembled dryer. Installed new belt, drum rollers, idler arm and blower. Read more

• No heat or not enough heat
• Takes too long to dry

Being a complete DIY I hate to call some unknown person into my home knowing that just to get them there will cost me more than I will spend for parts that I don't need.After all, they are trying to make a living and by selling me parts that I don't need will increase their profits. I've dealt with APP before and was impressed by their site because I could find both mechanical and electrical drawings for almost everything I have. I looked up my dryer, decided what was probably the problem,... Read more

Had to purchase a new filter as the felt does not feed back into the ridge in the filter. It seems to me that the felt should not pull out so easily. My dryer isn't even a year old so I think this is a design failure. But the new filter works great and hopefully we won't have this problem again. Thank you for your prompt service! Read more

Had to replace motor and blower, and both were very easy fixes, both pieces fit just right. The do it yourself videos also helped alot too, so props to them...Thanx alot Read more

Replaced exhaust thermal cutoff switch. Sears wanted to charge for a service visit + parts and labor. $17 part, $6 shipping and I received the part the following day. Repair complete in less than an hour at a fraction of the cost. Thanks appliance pros. Read more

• No heat or not enough heat

Being a complete DIY I hate to call some unknown person into my home knowing that just to get them there will cost me more than I will spend for parts that I don't need.After all, they are trying to make a living and by selling me parts that I don't need will increase their profits. I've dealt with APP before and was impressed by their site because I could find both mechanical and electrical drawings for almost everything I have. I looked up my dryer, decided what was probably the problem,... Read more

Disassembled dryer. Installed new belt, drum rollers, idler arm and blower. Read more

• Marks left on clothes
• Noisy

I'm new to how a dryer works, so I just started taking it apart to see what exactly was causing it. The video examples on the APP website were all amazing. It gave me a good idea of what I was getting into and showed me the common repair issues. The dryer being 12 years old, I was on the fence about repairing or replacing. However, once I got a list of parts I might need and getting the confidence by watching the videos, I said "what have I got to lose." The cause of the scraping and loud... Read more

Disassembled dryer. Installed new belt, drum rollers, idler arm and blower. Read more

I ordered a new motor. Read more

My Electrolux Frigidaire Gas Dryer stopped working and I got an error code E66 that the thermal limiter blew from over heating. The E66 code stops displaying after the initial code and you will then get a door open message. I replaced the thermal limiter and the thermostat just to be sure which part at the problem. The job is hard because you have to take apart the entire dryer and remove the drum. Would be a tough project to complete on your own. Read more

Simple unscrewed the set screw, removed the broken sensor-moisture part, attached the leads, and reattached the part to the back of the dryer. Took about 4 minutes. Read more

My Electrolux Frigidaire Gas Dryer stopped working and I got an error code E66 that the thermal limiter blew from over heating. The E66 code stops displaying after the initial code and you will then get a door open message. I replaced the thermal limiter and the thermostat just to be sure which part at the problem. The job is hard because you have to take apart the entire dryer and remove the drum. Would be a tough project to complete on your own. Read more

I looked on Appliance Parts Pros. com and read the problems that others had and replacing the ignitor made sense so I ordered one. It came by UPS within 3 days. I watched the video on how to replace it. Everything went easily, except the screw that held the ignitor in place was a philups head screwdriver and I couldn't get a screwdriver into the small space I had to work in so I went to Harbor Freight Tools and bought an inexpensive 90 degree rachet screwdriver for $2.99 and it worked great.... Read more

It was easy to find the part on appliance parts pros. Once I found it I studied the diagram and determined that there were 3 screws in the drum that needed to be removed. I disconnected power and then removed 3 interior screws. Once I did that I removed the back cover and removed the single screw on the bottom side of the air duct that held it in place connected to the heat tube. I then reversed disassembly. I want to tell you this is a 2 person job. In order to assemble it you need to... Read more