Kenmore Compactor 665.1386582 (6651386582, 665 1386582) Parts

• Compactor ram gets stuck
• Noisy

The compactor failed with the ram down, so the drawer wouldn't open which in turn made the mounting brackets inaccessible. This necessitated sliding a thin oscillating saw blade between the cabinet face frame and the counter top to cut through the brackets. It was then possible to roll the unit out and place it on its side. I removed the five screws holding the bottom pan in place, dropped the pan exposing the gear/chain train. The large gear was cracked from shaft out to the edge. One of... Read more

• Doesn't stop at end of compacting cycle

I removed the bottom access plate to look at the drive mechanism and check the chain and gears. I confirmed the bigger drive gear was broken in three pieces. Once I replaced the gear and adjusted the distance between the two gears (which is really close to prevent the gears from losing contact and stripping them) it works great. Read more

Replaced It With New One Read more

Touch up paint Read more

• Shakes and moves

REPLACING THE SUSPENSION PADS AND REPLACE THE BALNCE RING EVEN IF MY DIDN'T LEAK ANY FLUID OUT OF IT... IT SOLVE THE PROBLEM, IT WORKS BETTER NOW THAN IT EVER DID, THE ONLY THING I COULD COME WITH IS THE MANUFACTURE PUT THE WRONG BALANCE RING IN IT TO START WITH... MY IS A 400 KENMORE TOP LOADER, IT IS THE EASIES WASHER I HAVE EVER TAKEN A PART.. I WISH CARS WERE THAT EASY... IT TOOK ME OVER A MONTH FIGHTEN THIS PROBLEM UNTIL I FOUND IT ON YOUTUBE... WHAT BLESSING IT WAS... Read more

• Won't start
• Doesn't stop at end of compacting cycle

Original part was not available. Did some cross referencing and found s similar part Read more

Replace the white color covers with the new parts. Read more

Rood Cause #1: One of the front roller bearings was worn out and did not spin freely. Solution #1: I replaced the two front roller bearing assemblies (both included 2-pack). Rood Cause #2: The bottom surface of the compactor slide-out assembly had become deformed (convex) most likely due to the repeated force of compaction over the years. This bottom surface rubbed against the lower frame as evidenced by removal of paint (bare metal was exposed). Friction prevented the compactor drawer... Read more

Seal and adhesive. Read more

Replaced the motor with a direct replacement part. The wiring was not the same because the switch on the motor was different. The instructions that came with the motor were enough for me to figure out what to do. Read more

One day my wife went to bake something and the bake/broil buttons as well as #3, #9, and oven light ceased to work. Local repair guy came by and wanted to charge $500 to fix it....YEAH RIGHT! Did a little homework and found this website, spoke with knowledgable staff who pointed me in the right direction. Took me all of about 20 minutes to install new control panel..everything works perfect...THANKS! p.s. In doing my research come to find Maytag did little to insulate control panel from oven... Read more

I had no hope of separating the panel from the frame without damaging the frame since the two parts were rusted pretty badly and the screws holding the panel to the frame were completely beyond salvage. So I had to replace both the panel and the frame. I ended up removing the electrical/electronic connections, removing the panel/frame from the hinge and then replacing it with the new parts. Took about 90 minutes but the hardest part was removing other items from the rusting frame without... Read more

Ordered the part, which arrived incredibly fast and switched out old one for the new. Read more

Rood Cause #1: One of the front roller bearings was worn out and did not spin freely. Solution #1: I replaced the two front roller bearing assemblies (both included 2-pack). Rood Cause #2: The bottom surface of the compactor slide-out assembly had become deformed (convex) most likely due to the repeated force of compaction over the years. This bottom surface rubbed against the lower frame as evidenced by removal of paint (bare metal was exposed). Friction prevented the compactor drawer... Read more

After shopping for a new Whirlpool Thin Twin Stack, Found appliance parts pros online and decided to take it apart to see if repair was a possibility. APPro's online instructions were easy to follow, in a couple hours it was apart, and I placed the order. Reg ground took a week from NY, so the laundry piled up that week. The parts arrived on Monday morrning, by afternoon the machine was running like new! The cause was the belt tensioner pulley had frozen. Replaced it, drum wheels,snap... Read more

Replace element Read more