Bosch Dishwasher SGI45E12GB Parts

Rotating spray arm distributes water across dish racks during wash cycles. Replace if clogged with mineral deposits, cracked, or damaged from impact.

Fix a dishwasher that won't power on or reset with this on/off switch. Replaces worn or moisture-damaged switches. DIY-friendly installation.

Seals the detergent dispenser to prevent leaks and ensure proper release during wash cycles. Replace if detergent leaks or dispenser malfunctions.

The Sealing is an OEM replacement part for Bosch brand dishwashers. Located on the perimeter of the small rinse aid compartment door, this resilient rubber piece forms an essential water-tight seal when the dispenser is closed.   

Symptoms of a potentially problematic rinse aid door sealing include:

• Leakage or spills within the rinse aid reservoir
• Mineral deposits or residue build up inside the compartment  
• Cracks, tears, or deformation of the sealing material

Causes of a faulty rinse aid door sealing can be repetitive opening/closing stress breaking down pliability long-term. Exposure to chemical vapors from the rinse aid may also degrade sealing properties.

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

2 clamps included.

Fix dishwasher not heating or running for hours. This NTC temperature sensor monitors water temp and prevents overheating. Moderate DIY repair with video.

Detergent not dispensing during wash cycle? This actuator arm with spring releases the detergent cup at the right time. Moderate DIY repair.

Seals the NTC temperature sensor port in your dishwasher to prevent leaks and ensure accurate temperature readings. Replace if leaking or worn. Verify fit with your model number before ordering.

Circular sealing gasket creating watertight joints between dishwasher components. Replace when flattened or cracked to prevent leaks. Confirm fit by model.

The Impeller Jug is an OEM part for Bosch dishwashers. Located inside the wash chamber, the impeller jug is responsible for evenly distributing water throughout the dish rack during the wash cycle. It features strategically placed holes and channels that work with the spray arms to direct water flow and ensure all dishes receive thorough coverage. 

Symptoms of a bad impeller jug include:

• Incomplete cleaning even on short or heavy wash cycles  
• Dirty dishes remaining at the end of the cycle
• A buildup of food or grime deposits inside the wash chamber
• Off-balanced or excessive noise levels during washing

Causes of failure can be mineral or scale buildup inhibiting water flow, cracked or damaged casing allowing leaks, or worn impeller fins no longer efficiently dispersing water. Over time, hard water deposits and normal use can degrade performance. 

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore dishwashers. 

Left side door hinge for your dishwasher. Replaces damaged, bent, or broken hinges that cause the door to fall open or swing too far. Bushing included.

Replace your dishwasher's upper rack rail if cracked, broken, or worn. This guide rail installs along the sides to support smooth rack sliding.

Leaking water around the inlet valve? This rubber inlet seal creates a watertight connection at your dishwasher's water inlet to stop drips and leaks.

This replacement seal forms a tight barrier to help prevent leaks and maintain normal appliance operation. It restores the sealed connection between mating components so the appliance can contain water or air as designed. What it does:

• Creates a watertight/airtight seal between mating parts to help prevent leaks
• Helps stop water pooling, dripping, or unexpected moisture near the appliance
• Restores proper fit where worn or damaged seals allow loss of pressure or fluid
• Supports stable operation by maintaining the intended interface between components

• Disconnect power and water supply before starting any repair
• Remove the old seal and clean mating surfaces of debris and residue before installing the new seal
• Align the seal carefully and seat fully to avoid pinching or gaps

This cover caps the end of the condensation hose inside the dishwasher, preventing leaks and ensuring proper drainage of condensation during the drying cycle. It snaps or presses into place over the hose opening. Replace this cap if it is cracked, missing, or if you notice water leaking beneath or around the dishwasher during operation.