Kenmore Refrigerator 106.50212010 (10650212010, 106 50212010) Parts

Best Seller

Genuine Whirlpool part

Ice Door Kit

By: Whirlpool

Part Number: W10823377

Includes door, support, spring and mechanism delay. No longer uses the ribbon heater due to the improved foam design. If your refrigerator uses this ice door kit and the mounting tabs are broken you can use the broken tab ice door kit 8201756.

This part fixes the following symptoms

Door sweating
Door won't open or close
Freezer section too warm

Do-It-Yourself Stories from Customers like You Ice cube dispenser/flap was broken not actuating the ice bucket motor. Peter P. • Sonoma , CA • July 24, 2023

Ice Door Kit, Control Bracket, and Ice Dispenser Guide were purchased. I followed two videos on replacing the parts. The Control Bracket WP2180226 / AP6005965, was straight forward and I discovered a snapped pin on the old bracket causing an electric switch to be out of place... that repair was easy. When it came to the hinges of the ice chute, I discovered the snap-in, on right side, of the hinge was cracked... this is why the pin escaped. This cracked part is molded into the entire... Read more

Best Seller

Genuine Whirlpool part

Alumilastic Cement

4.9 (17)

By: Whirlpool

Part Number: WP4317852

The Alumilastic Cement is an OEM part for Whirlpool appliances, typically used in refrigerators and freezers. It serves as a thermal mastic compound, designed to provide a secure and heat-conductive bond between various components, such as evaporator coils and the interior walls of the appliance.

Causes of a bad alumilastic cement can include drying out, cracking, or losing its adhesive properties over time. This can occur due to age, exposure to temperature fluctuations, or improper application. When the cement fails, it can lead to poor thermal conductivity and decreased cooling efficiency.

Symptoms of a bad alumilastic cement include:

Reduced cooling performance
Unusual noises from the cooling system
Components becoming loose or detaching
Increased energy consumption

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Do-It-Yourself Stories from Customers like You Ice maker wouldnt make ice Ty G. • Lewis Center , OH • December 30, 2014

I used your online troubleshooting tips and watched the videos on your site. I determined my thermostat was defective, ordered the thermostat which arrived in two days and I replaced the thermostat and I now have a full bin of ice !!! The do it yourself video was extremely helpful and made the repair very easy. Thanks so much for the great service and quick delivery !!! Read more

Genuine Whirlpool part

Lever, Ice Dispenser (Wht)

4.9 (18)

By: Whirlpool

Part Number: WP2180259

The Ice Dispenser Lever is an OEM component specifically designed for Whirlpool side-by-side refrigerators with built-in ice dispensers. Located inside the ice and water compartment, the lever is responsible for releasing cubed or crushed ice when engaged.

Symptoms of a bad ice dispenser lever include:

Failure to dispense ice when the lever is lifted
Loose, wobbly, or uneven movement of the lever
Ice dispenser mechanism not triggering properly

Causes of a bad lever can be worn gears or connector linkages inside the ice dispensing mechanism from repeated use over time.

This OEM Whirlpool part is also compatible with Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, and select Kenmore fridge models.

Do-It-Yourself Stories from Customers like You The ice dispenser lever was cracked and did no longer trigger the dispensing of the ice Andrea M. • Honolulu , HI • March 01, 2015

I replaced the Ice Dispenser Lever. Since the replacement part is only available in white and my fridge is bone, I replaced also the Water Dispenser Lever, so it looks much better. I followed the instructions in the video, which were very useful and very well done. My problem was that the refrigerator is a KitchenAid built-in, while the instructions were for a Whirlpool, so the removal of the faceplate was quite different from what was shown in the video and more difficult. Also there were some... Read more

Genuine Whirlpool part

Fan Motor Retainer (Refrigerator)

5.0 (2)

By: Whirlpool

Part Number: WP2155590

This fan motor retainer secures the refrigerator's fan motor to its mounting bracket or shroud, reducing vibration and keeping the fan aligned so air circulates properly for consistent cooling.

Secures the fan motor to its bracket or shroud
Maintains proper fan alignment and clearance for consistent airflow
Helps reduce vibration, buzzing, or rattling from a loose motor
A worn or missing retainer may present as scraping fan noises or uneven airflow

What's included: 1 fan motor retainer

Disconnect power to the refrigerator before servicing; allow moving parts to stop and wear cut-resistant gloves
Access the fan area per your model
Transfer the motor into the new retainer and reinstall using existing hardware as required
Ensure the fan blade spins freely and clears the shroud before restoring power

Do-It-Yourself Stories from Customers like You Evaporate motor went out on my Whirlpool refrigerator freezing cold at the bottom but warm on top Toan N. • Anaheim , CA • June 24, 2018

When I first found out that the evaporator fan doesn't work, I went to a local home appliances store to buy one , cost me $40 , real easy to replace it and it solves the main problem , but this evaporator motor was making some loud noise every now and then , especially when we open the door too often. Then I ordered another one from Repair Clinic , this one is even worst , making a loud hum noise constantly, I had to return it. My wife really wants to buy another refrigerator but I don't... Read more

Genuine Whirlpool part

Refrigerator Shelf Support Stud

By: Whirlpool

Part Number: 4388405

Secures refrigerator shelves to the liner wall. Replace this stud if shelves sag, sit unevenly, or won't stay in place due to broken or missing support.

Genuine Whirlpool part

Screw (Mounting)

5.0 (1)

By: Whirlpool

Part Number: WPW10191952

This factory fastener secures panels, brackets, or internal components in your appliance. Replacing a missing or damaged screw restores a tight fit, reduces rattles, and keeps assemblies properly aligned for dependable operation.

Fastens sheet-metal panels, braces, and trim to the cabinet/frame
Helps maintain alignment and structural integrity of assemblies
Can reduce vibration noises and looseness caused by missing/stripped hardware
Replace if the head is rounded, threads are worn, or the screw is corroded

What's included: One screw Install notes:

Disconnect power; for gas or water appliances, also shut off the supply
Match location and start threads by hand to avoid cross-threading
Use the correct driver size; tighten snugly without overtightening

Do-It-Yourself Stories from Customers like You Broken drawer Rhonda D. • Calimesa , CA • March 23, 2015

Replaced drawer Read more

Genuine Whirlpool part

Handle

5.0 (3)

By: Whirlpool

Part Number: WPW10285542

Do-It-Yourself Stories from Customers like You The handles were turning slightly yellowish, while the rest of the fridge was bright white. Dr N S. • The Woodlands , TX • February 01, 2020

I bought new handles and changed them. The video on your site was VERY helpful, so the installation was simple and done in 10 minutes. Read more

Genuine Whirlpool part

Arm-Pivot

By: Whirlpool

Part Number: W11256541

Genuine Whirlpool part

Control Cam Kit

By: Whirlpool

Part Number: WP2182195

Genuine Whirlpool part

Slide

By: Whirlpool

Part Number: 1115380

Genuine Whirlpool part

Enamel Paint

By: Whirlpool

Part Number: 4392900

Color: Biscuit. Size: 1 qt. can uncut. Enamel paint.

Genuine Whirlpool part

Fastener

By: Whirlpool

Part Number: 489285

Genuine Whirlpool part

Blade-Fan

4.5 (2)

By: Whirlpool

Part Number: 8201630

Do-It-Yourself Stories from Customers like You Fan noise Richard W. • Plano , TX • May 29, 2017

Removed the back cover to access the fan area. Clean the area with brush and vac first. Unplugged the Refrigerator. Used a socket set with 1/4" socket. Had an extended and a standard socket. Removed the condensate plastic drain from the bottom of the refrigerator to have more access to the fan. Unplugged the fan motor. Removed the two screws holding the fan in place. Removed the fan unit from the condenser side of the bracket. Place new fan on the fan and installed exactly the way I removed the... Read more