Kenmore Refrigerator 106.51149110 (10651149110, 106 51149110) Parts

Replaced It With New One Read more

Watched a video. Ordered a thermistor. Made the fix. $100 total including expedited shipping. Diagnosing the problem was more stressful than fixing. Read more

• Noisy

I pulled the refrigerator out, removed the back panel, disconnected the fan motor. I did not know how hard or easy it would be to remove the fan from the motor shaft so I removed the motor with the fan attached and then removed and replaced the fan. This would not be necessary if you have a lot of strength, but if you need leverage to push the fan down on the shaft you might want to disconnect and remove the motor fan assembly too. After replacing the motor assembly and reconnecting I tested by... Read more

My KitchenAid refrigerator was not cooling, but the freezer was working perfectly. The help section here listed three parts that could be defective–defrost thermostat, evaporator fan motor and blade, and air diffuser/damper control–so I replaced them all. The videos were EXCELLENT, and despite the difficulty I had squeezing my shoulders into the small freezer compartment, I installed the parts and my refrigerator is cooling perfectly! THANK YOU FOR THE EXCELLENT REPAIR VIDEOS! I am so happy... Read more

After trying so called super glue that was worthless. I ordered a new drawer from Appliance Parts. The new drawer arrived on the promised date, and after transferring a few small parts from the old drawer to the new one, all is well Read more

I had to replace my frig and the upgraded model didn't come with a dairy bin. I found a review for the model in which someone had done the research and found that the Kenmore Elite had a model of refrigerator that was designed like the Whirlpool but came with the bin. He ordered it for his Whirlpool and he says it fit. I ordered one and it fit on the top notches but due to the design, it would not open. I just shifted a door shelf up to the top and put the dairy bin under it and it works fine. Read more

The problem was that the motor coupler & shaft had a tiny bit of rust at their union. With the weight of the ice bin it rusted in the lowest position. This didn't allow the motor coupler to float on the shaft. There is a spring inside the shaft that pushes up on the motor coupler keeping it engaged in the ice bin coupler above. This coupler in turn rotates the auger in the bin to dispense the ice. I removed the motor coupler & shaft, tapped the coupler loose and filed off the rust. This allowed... Read more

I purchased replacement parts to completely replace basket, face plate, and rollers. I received exactly what I ordered. The only problem I had was removing the part(s) from the shipping box. I thought the part came assembled (as rollers had been installed onto the basket), but the face plate had not been snapped into place. When I removed everything from the shipping box as one piece, the face plate fell off, hit the tile floor, and cracked. Bummer. Since the original face plate was in good... Read more

Replaced the actuator pad on the Whirlpool Gold Series, releasing the electronic menu pad to get to the water activator pad was the biggest hurdle. The release tabs are underneath the menu pad and you may feel as if you may break them when releasing them. They did not break but I did hold by breath. Read more

I noticed Ice maker Quit for the third time in 15 years so I decided to buy another Ice maker, I installed it and NO ice still?? Well I went after the other problem thinking if it does not get cold enough maybe ice maker won’t work. I ordered Defrost Switch, Heater and Evaporator Fan just to be safe. I replaced all three, the fan was noisy, the heater OHM’d ok but I replaced it as did the defrost switch, I put it back together, the Freezer got to 0 degrees and the frig got to 38 degrees so I... Read more

Purchased 2 replacement feet risers. A very awkward repait. Read more

Replaced a new rubber seal, it took me approx forty minutes. It works perfect, the door seals correct now. Thanks to the instruction supplied from appliance parts pros.com. Read more

The problem was that the motor coupler & shaft had a tiny bit of rust at their union. With the weight of the ice bin it rusted in the lowest position. This didn't allow the motor coupler to float on the shaft. There is a spring inside the shaft that pushes up on the motor coupler keeping it engaged in the ice bin coupler above. This coupler in turn rotates the auger in the bin to dispense the ice. I removed the motor coupler & shaft, tapped the coupler loose and filed off the rust. This allowed... Read more

Replaced all the parts ordered and adjusted door. Took about one hour to complete. Read more

Ordered replacement light module Read more