Kenmore Refrigerator 106.57796703 (10657796703, 106 57796703) Parts

I took the new seal out of it's packaging and used a blowdryer on low heat to soften up the seal so that the crease from shipping (it was folded to ship) disappeared. Next I took the refrigerator door off, removed the old seal, & cleaned the area where the new seal would be applied. Following the video on the Appliance Pro Parts website, I re-installed the new seal and put the door back on. Last step was to snap on the new hinge cap I ordered. The video online was easy to follow and this... Read more

Replaced Case Water Filter assembly DA81-05883A. Please read my post entirely before starting. I completed all the tasks that I could without having to disconnect the refrigerator since it was full of food. First I removed the panel on top of the refrigerator that covers the water line that feeds the dispenser. Do not disconnect any electrical connections or the water line at this time. Remove the panel from the back bottom of the refrigerator that covers the compressor and water valve,... Read more

I searched the web for a replacement drawer to no avail. Once I reached this site I was pretty discouraged when your site also said my drawer was no longer available. A suggestion for a different replacement drawer that MAY work was my only option. I purchased the drawer with the understanding that it could be returned if it didn't fit. To my surprise it came in two days and fit perfectly. I am thrilled every time I open the fridge. I am VERY pleased with this purchase and would... Read more

Followed the video you provided. Read more

Replaced filter cap with new one. The minor challenge was to find a method of pulling the filter out of refrigerator (which is normally done by pulling on the filler cap. The filter was recessed to far into the refrigerator for me to be able attach the new cap. I had to find another tactic to remove the filter. The solution was to look at the replacement filter to notice where two slots were located at the end of the filter. I then used a paint can opener (found at most paint stores) to slip... Read more

The problem was that the motor coupler & shaft had a tiny bit of rust at their union. With the weight of the ice bin it rusted in the lowest position. This didn't allow the motor coupler to float on the shaft. There is a spring inside the shaft that pushes up on the motor coupler keeping it engaged in the ice bin coupler above. This coupler in turn rotates the auger in the bin to dispense the ice. I removed the motor coupler & shaft, tapped the coupler loose and filed off the rust. This allowed... Read more

This was actually one of the easiest fixes I’ve done. All that was required was to remove 3 screws to remove the broken part. I used a pair of pliers to remove the moisture sensors from the broken part to the new one. Read more

• Leaking

I have a Whirlpool Side-by-side Model ED22PWXBW01. A year ago, the ice cubes started freezing together in the rear of the ice bin for no apparent reason. Although the problem started off small, it gradually grew much worse, and finally I could see water dripping out of the ice mold and into the bin during the fill cycle. Re-levelling the refrig didn’t help, nor did adjusting the cube size / fill level. With guidance from the video, I removed the icemaker from the wall of the freezer. The... Read more

Replaced inlet valve. Read more

I noticed Ice maker Quit for the third time in 15 years so I decided to buy another Ice maker, I installed it and NO ice still?? Well I went after the other problem thinking if it does not get cold enough maybe ice maker won’t work. I ordered Defrost Switch, Heater and Evaporator Fan just to be safe. I replaced all three, the fan was noisy, the heater OHM’d ok but I replaced it as did the defrost switch, I put it back together, the Freezer got to 0 degrees and the frig got to 38 degrees so I... Read more

The problem was that the motor coupler & shaft had a tiny bit of rust at their union. With the weight of the ice bin it rusted in the lowest position. This didn't allow the motor coupler to float on the shaft. There is a spring inside the shaft that pushes up on the motor coupler keeping it engaged in the ice bin coupler above. This coupler in turn rotates the auger in the bin to dispense the ice. I removed the motor coupler & shaft, tapped the coupler loose and filed off the rust. This allowed... Read more

Easy to remove the metal parts from the old bin. The only problem was that the screw that holds the adapter has red thread locker and screwdriver rounded off the head of the screw. Drilled the screw and heated the screw to loosen the thread locker and used an ease out to remove the screw. Read more

• Light not working

I saw your video on you tube and it seems very easy to do it my self, so I ordered the parts and I did it my self. It was very easy. Thank you for sharing with us on how to did it. One more thing, the parts arrived on the time they said it would come. Read more

Replaced icemaker and shutoff arm. Easy project. Read more

Reviewed the AppliancePartsPros.com site and decided that the most likely suspect was the ice motor. I ordered one and got it FAST! I removed the water ice tray in the bottom of the Ice/water kiosk which exposed two phillips screws which I removed. The front panel came off by lifting upward and unplugging it. The ice door motor was visible near the top of the opening. I removed the hex head screws with a 1/4" nut driver so the ice door assembly was free. The core control board was hidden... Read more

Found the parts in the diagram of my fridge and simply installed it very easy Read more