Kenmore Washer 110.15944400 (11015944400, 110 15944400) Parts

The Shaft Seal is an OEM part for Whirlpool washing machines. This seal is designed to fit around the shaft that connects the tub to the transmission or motor, preventing water from leaking out of the tub and into the machine's internal components.

Causes of damage to the Shaft Seal often involve normal wear and tear from regular use, as the constant motion of the shaft can gradually degrade the seal.

Symptoms of a bad Shaft Seal include:

• Water leaking from the underside of the washing machine, particularly during or after a wash cycle
• A noisy operation, especially during the spin cycle, can sometimes result from water leaking into the bearings and causing them to fail
• The presence of rust or corrosion around the area where the shaft enters the tub

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Self-Leveling Leg Spring is an OEM replacement part for Whirlpool washers. It is responsible for stabilizing the washer and ensuring it sits level on uneven surfaces. Each spring is individually designed to compress or extend based on the weight and load distribution inside the washer tub. 

Causes can include failure of the compression spring over many usage cycles, or damage from over-compressing the spring through excess weight loads. 

Symptoms of a bad self-leveling leg spring include:

• The washer rocks or wobbles noticeably during operation  
• Excessive vibration transferred to nearby appliances or cabinets
• Difficulty loading and unloading clothes due to an unleveled washer 
• Premature wear of internal components like bearings from prolonged off-balancing

This genuine Whirlpool OEM replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Knob Spring Clip is an OEM part for Whirlpool appliances, specifically designed for use in washers and dryers. This small but essential component is responsible for securing the control knob to the control panel, ensuring that the knob stays firmly in place during operation.

Common causes of a bad spring clip include frequent use, accidental impacts, or wear and tear over time. A faulty spring clip can result in the control knob becoming loose or falling off, making it difficult to operate the appliance.

Symptoms of a bad knob spring clip include:

• The control knob is loose or wobbly
• The control knob falls off easily
• Difficulty in turning or setting the control knob
• The appliance not responding correctly to knob adjustments

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Whirlpool top load washer agitator inner cap seal is an OEM replacement part responsible for providing a tight seal and preventing water from leaking in to the agitator. The inner cap seal is located underneath the agitator cap at the top of the agitator assembly.

Over time, the Inner Cap Seal can become worn, cracked, or damaged due to repeated exposure to water, detergents, and the high-speed spinning of the tub. A faulty seal can lead to water leaks, excessive noise, and potential damage to other components.

This part fixes the following symptoms:

• Water leaking from the agitator assembly during operation
• Excessive splashing or spraying of water during the wash cycle
• The agitator not moving or agitating properly
• Visible wear, tears, or damage to the inner cap seal
• Difficulty in removing or reattaching the agitator assembly

The Whirlpool inner cap seal can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Internal Drain Hose is an OEM part for Whirlpool washing machines. This hose is responsible for carrying used water from the washer tub to the drain pump, facilitating the efficient removal of water during the drain cycles. It ensures that water is properly directed out of the washer, preventing leaks and maintaining optimal washing performance.

Causes of a bad internal drain hose can include blockages from debris or lint, wear and tear from regular use, or damage such as cracks or splits from mishandling or aging.

Symptoms of a bad internal drain hose include:

• Water leaking inside or around the washer
• Slow or incomplete draining
• Error codes related to draining issues
• Unusual noises during the drain cycle

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Tub to Pump Hose is an OEM replacement part for Whirlpool washing machines. It connects the washer tub assembly to the pump, carrying water drained from the tub into the pump housing. This hose is a component that allows the machine to drain water efficiently during the spin cycle.

Causes of a bad tub to pump hose can include mineral buildup that restricts water flow, fatigue and wearing that cause cracks or splits, damage from rodents or sharp/heavy objects in the wash load, and deterioration from age that increases brittleness.

Symptoms of a bad hose include:

• Water leaks during or after the drain cycle
• Inability to fully drain water from the tub
• Water remaining in the tub after spinning

This genuine Whirlpool OEM replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Bearing and Seal Kit is an OEM component for Whirlpool and KitchenAid front-load washing machines. The kit includes 2 center post bearings, 3 agitator shaft seals, and 1 center post seal.

These internal seals help retain lubrication inside the motor shaft housing, while the bearings allow for smooth rotation of critical components like the drive pulley. Continuous belt rubbing and water exposure diminish their lifespan over time.

Symptoms of worn motor seals or bearings include:

• Abnormal vibrations during the wash or spin cycles
• Noisy operation and grinding sounds from the motor
• Difficulty starting or stopping the cycle

This OEM kit is also compatible with Maytag, Jenn-Air, Magic Chef, and select Kenmore models.

The Spring Mounting Bracket is an OEM part for Whirlpool washing machines. It is located at the bottom of the appliance, near the base. It provides a secure attachment point for the suspension springs, which help absorb vibrations and stabilize the drum during operation.

Causes of a faulty spring mounting bracket can include regular wear and tear, physical damage, or improper installation. These factors can result in issues such as excessive shaking or movement of the appliance, increased noise during operation, or unbalanced loads.

Symptoms of a bad spring mounting bracket may include:

• Excessive shaking or movement of the appliance during operation
• Increased noise or rattling sounds during the wash or drying cycle
• Unbalanced loads, causing the drum to tilt or not spin properly

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Upper Transmission Shaft Seal is an OEM replacement part for Whirlpool washing machines. This seal is designed to prevent water from leaking out of the washer tub and into the transmission, ensuring the proper function of the washing machine's internal components.

Causes of a bad upper transmission shaft seal can include wear and tear from regular use, exposure to harsh detergents, or damage from foreign objects. Over time, the seal material can degrade, leading to leaks and reduced efficiency.

Symptoms of a bad upper transmission shaft seal include:

• Water leaking from the bottom of the washing machine
• Unusual noises during the spin cycle
• Transmission oil stains on the floor
• Poor washing performance

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Clutch Band and Lining Kit is an OEM part for Whirlpool washing machines. It contains the clutch band and clutch lining components essential for proper transmission of power from the washer motor to its drum during the spin cycle. The clutch band and lining allow for a controlled amount of slippage to safely extract water from clothes without damage. 

Symptoms of a bad clutch band and lining include: 

• Excessive noise or vibration during spin
• Slow or ineffective spinning 
• The drum failing to spin or “locking up”
• Premature wear of other transmission parts

Over time and with heavy use, these components can wear down. If slipping or damage is detected, it’s important to replace the kit to avoid potential transmission repairs.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Counterbalance Spring Kit is an OEM part for Whirlpool washing machines. This kit includes springs that help balance and stabilize the washer drum during the spin cycle, preventing excessive movement and vibration. The counterbalance spring kit includes 3 counterbalance springs. The counterbalance spring kit includes 3 counterbalance springs.

Over time, counterbalance springs can wear out, lose tension, or become damaged due to repeated use and the strain of heavy loads. A faulty counterbalance spring can lead to instability and increased noise during operation, affecting the washer's performance.

Symptoms of a bad counterbalance spring kit include:

• Excessive shaking or vibrating during the spin cycle
• Loud banging or thumping noises
• The washing machine moving or "walking" during operation
• Unevenly distributed loads or off-balance errors

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Vacuum Break Hose is an OEM part for Whirlpool washing machines. It connects the vacuum break to the outer tub, preventing siphoning and ensuring proper water levels during the wash cycle. This hose plays a crucial role in maintaining the efficiency and performance of the washing machine by regulating the water flow.

Causes of a bad vacuum break hose can include wear and tear over time, kinks or blockages in the hose, or damage due to improper installation or handling. A compromised hose can affect water levels and overall washing performance.

Symptoms of a bad vacuum break hose include:

• Water not draining properly
• inconsistent water levels in the tub
• Leaks or puddles around the washing machine
• Error codes related to water flow or pressure

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Appliance Touchup Paint is an OEM product for Whirlpool appliances. This touchup paint is used to cover scratches, chips, and minor blemishes on the surface of various appliances, helping to maintain their appearance and protect them from rust and other damage. It is specifically formulated to match the original color and finish of Whirlpool appliances, ensuring a seamless repair.

Causes of needing touchup paint include everyday wear and tear, accidental impacts that cause chipping or scratching, and exposure to harsh cleaning chemicals that can damage the finish. Regular use of touchup paint can help keep appliances looking new and extend their lifespan.

Symptoms indicating the need for Appliance Touchup Paint include:

• Visible scratches or chips on the appliance surface
• Areas of exposed metal prone to rust
• Blemishes that affect the overall aesthetic of the appliance

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Front Leveling Foot is an OEM part for Whirlpool washing machines. It is designed to support and stabilize the washer by allowing users to adjust the height and level the appliance on uneven floors. Proper leveling ensures smooth operation and minimizes vibrations and noise during wash cycles.

Causes of a bad Front Leveling Foot can include physical damage from excessive force, wear and tear from frequent adjustments, or corrosion due to exposure to water or laundry chemicals. Over time, these factors can compromise the foot’s ability to maintain stability, leading to operational issues.

Symptoms of a bad Front Leveling Foot include:

• The washing machine rocking or wobbling during operation
• Increased vibration and noise
• The washer being unlevel, affecting wash performance
• Difficulty in adjusting the foot

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Agitator Washer is an OEM part for Whirlpool washing machines. It is designed to fit between the agitator and the agitator drive shaft, ensuring smooth and effective agitation of clothes during the wash cycle. 

Over time, the agitator washer can wear out or become damaged due to the constant movement and pressure exerted during wash cycles. Causes of a bad agitator washer can include normal wear and tear, exposure to heavy loads, or misuse that puts excessive stress on the part.

Symptoms of a bad agitator washer include:

• Agitator not moving or moving improperly
• Unusual noises during the agitation cycle
• Poor cleaning performance
• Agitator becoming loose or detached

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Hose Clamp is an OEM part for Whirlpool appliances. It secures hoses in place, ensuring a tight connection and preventing leaks in various systems such as washing machines, dishwashers, and refrigerators. This clamp is crucial for maintaining the integrity of the water or air lines it secures.

Causes of a bad hose clamp include wear and tear over time, exposure to water and detergents, or mechanical stress from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Leaks at the hose connection points
• Hoses slipping off the connections
• Visible rust or damage on the clamp
• Reduced appliance efficiency due to leaks

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.