Kenmore Washer 110.21392012 (11021392012, 110 21392012) Parts

The lid hinge bearing is used for the lid hinges on washers and dryers. When functioning properly, it allows the lid to open and close properly. If this is a problem with the bearing, it could make the lid difficult to move. In some cases, when the lid will not close, it means that the machine will not function correctly. Damaged lid hinge bearings should be replaced as soon as possible.The lid hinge bearings see a lot of work since they are in use whenever the lid of the washer or dryer opens and closes. They could become cracked and broken over time. Replacing the bearings is a relatively simple repair that owners can make on their own.This lid hinge bearing is for use with many models of washers and dryers from Whirlpool, KitchenAid, Roper, Estate, Inglis, Maytag, Admiral, Amana, Crosley, and Magic Chef. This is a genuine OEM replacement part that has been sourced from the manufacturer. The piece is sold individually, so if owners need to replace more than one hinge, they will need to buy multiples.

This replacement part is intended to replace a broken or defective gear case in washing machines.The gear case rotates the washing machine's basket by driving the agitator. The user may notice the basket does not spin efficiently, if at all, and this the gear case may need to be replaced. Before any repairs are made, the washing machine should be entirely disconnected from the power and water sources. It's recommended that work gloves are worn to ensure proper protection. This is a genuine OEM part made by Whirlpool and has been sourced directly from the manufacturer. As an authentic replacement part, this gear case is suitable for installation in multiple different models of washing machines that have been manufactured by Whirlpool, Kitchenaid, Maytag, and various other brands. This is a genuine part made of high-quality, durable materials and is sold individually.

This replacement screw secures panels, brackets, and other components in your appliance to keep them aligned and rattle-free. Replacing worn, stripped, or missing hardware restores a tight fit and helps maintain safe, quiet operation.

• Fastens panels, brackets, or internal parts to the cabinet/frame
• Helps maintain alignment to reduce vibration and rattling
• Replaces lost, stripped, or corroded screws
• Common symptoms: loose panels/trim, rattles, or a screw that won't tighten

• Disconnect power; shut off water or gas if applicable
• Match thread and length to the original; replace one at a time to keep alignment
• Start threads by hand to avoid cross-threading; use the correct driver
• Tighten snugly—do not overtighten, especially into plastic or thin sheet metal

This bleach dispenser for a washing machine holds liquid bleach and releases it into the tub at the appropriate point in the cycle, helping dilute bleach and protect fabrics from contact with undiluted solution. What it does:

• Holds and meters liquid bleach until the machine calls for dispensing
• Helps ensure bleach mixes with water for even, diluted distribution
• Replace if cracked, clogged, or leaking
• Common symptoms include bleach not dispensing, bleach left in the cup, leaks around the dispenser area, or bleach spots on fabrics

• 1 bleach dispenser

• Disconnect power and turn off water before servicing
• Access and mounting vary by model; follow your service manual to reach the dispenser
• Detach hoses/clamps or fasteners, transfer any reusable hardware, and seat the new dispenser fully
• Reconnect, then run a test fill/rinse to check for proper dispensing and leaks

This mixing valve bracket secures the washer's water inlet valve to the cabinet, keeping the valve steady and properly aligned for hose connections. A correct-fit bracket helps reduce rattles and potential leaks caused by a loose valve.

• Mounts and supports the water inlet/mixing valve on the rear panel
• Maintains proper alignment for hot and cold supply connections
• Helps reduce vibration and rattling noises during fill
• Common signs it's needed: loose or dangling valve, misaligned hose connections, or leaks at the valve fittings

• Disconnect power and turn off both water supplies; relieve pressure before removing hoses
• Access the rear of the washer and remove fasteners securing the existing bracket/valve
• Transfer the valve to the new bracket, reusing the original hardware
• Reattach the bracket to the cabinet, reconnect hoses, restore power and water, then check for leaks

This rotary encoder mounts behind the washer's cycle knob and tells the main control which setting you select. When it fails, selections may be erratic or unresponsive. Replacing it restores accurate, dependable cycle selection. What it does

• Detects the position of the cycle selector knob
• Sends selection signals to the main control board
• Enables precise cycle and option changes
• Common symptoms: knob turns but lights don't follow, random/incorrect selection, can't select a cycle, won't start

• One rotary encoder

• Disconnect power to the washer before servicing
• Access the control console and remove the knob/dial to reach the encoder
• Note orientation, unplug the harness, release tabs/screws, and swap in the new encoder
• Handle electronics carefully and avoid static discharge; verify knob-to-light tracking before reassembly

This factory screw secures panels, brackets, and other components in your appliance. Replace a missing, stripped, or corroded fastener to restore a tight fit and keep parts properly aligned and rattle-free.

• Secures appliance components and panels in their mounting points
• Replaces damaged, stripped, or missing hardware
• Helps reduce rattling or vibration from loose parts

• Disconnect power; shut off water or gas supplies if applicable
• Match location with the original screw; start threads by hand to avoid cross-threading
• Tighten until snug; do not over-torque, especially into plastic or thin metal
• Reinstall any covers or panels and test for secure fit

Includes water inlet valve, vacuum break, wire harness and connector hose.

This pump drain filter helps protect the appliance's drain pump by screening out debris before it enters the pump. A clean, intact filter supports proper draining and helps prevent clogs and pump damage.

• Screens debris before it reaches the drain pump
• Helps maintain proper draining performance
• May resolve issues like slow or incomplete draining, standing water, or drain-related noises
• Replacing a damaged or missing filter can reduce repeat clogs

• Unplug power and shut off water supply before service
• Access location varies by model; have towels ready for any residual water
• Note orientation of the old filter for correct placement
• After installation, check for leaks and run a brief drain cycle to verify operation

This replacement screw secures panels, brackets, and internal components within your appliance. Replacing a missing or damaged fastener restores a tight fit, reduces vibration and noise, and helps keep parts properly aligned during operation.

• Fastens panels, trim, brackets, or internal components to the chassis
• Maintains proper alignment and stability during normal use
• Replaces missing, rusted, or stripped hardware
• Common symptoms: loose or rattling panels, vibration, difficulty fastening, or a visibly missing screw

• Disconnect power; for gas appliances, also shut off the gas supply
• Match length and thread to the original; replace one-for-one in the same location
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• If the receiving hole is stripped, repair threads or replace the clip/nut before installing

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

Extends the drain hose approximately 4 feet. You must also order a drain hose connector kit: 285835.

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear bulkhead to the tub, ensuring vibrations are reduced through solid mounting points. Properly installed screws dampen oscillating movement.

Causes of a bad screw include damage from water exposure like corrosion or breakage from stress concentrations if the tub bangs around during imbalanced loads. 

Symptoms of a bad screw include:

• Loose or detached rear bulkhead allowing side-to-side play
• Excessive noise and shaking felt through the surrounding walls   
• Development of micro-cracks around screw holes over time
• Potential leak paths if holes are no longer sealed 

This Whirlpool replacement screw restores a stable suspension system. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This adjustable leveling leg helps stabilize and properly level your appliance on uneven floors. Replacing a worn or missing leg reduces wobble and vibration so doors align and the unit operates smoothly.

• Screws into the base to raise or lower a corner for precise leveling
• Helps prevent rocking, vibration, and rattling during use
• Promotes even weight distribution to protect the cabinet and flooring
• Restores proper door/drawer alignment once the unit is level

• Disconnect power; shut off water supply before servicing
• Carefully pull or tip the appliance to access the leg; use a helper for safety
• Start threads by hand, then adjust height with a wrench—do not over-extend
• Verify level front-to-back and side-to-side; recheck after moving or loading

Includes connector and both clamps.

This replacement nut is a small hardware fastener used to secure components inside your appliance. It helps keep parts tight and properly aligned so assemblies don't loosen from vibration or normal operation.

• Threads onto a mating bolt, stud, or shaft to clamp parts together
• Maintains alignment and reduces movement and rattling
• Replaces a stripped, missing, or damaged nut to restore a secure fit
• Common signs of failure: loose panels or components, unusual vibration/noise, hardware missing

• Disconnect power; shut off gas and/or water if applicable before servicing
• Note the original hardware stack-up (washers/spacers) and orientation for reassembly
• Start by hand to avoid cross-threading; tighten to manufacturer guidance—do not overtighten
• Replace any damaged washers or locking devices