Kenmore Washer 110.22956100 (11022956100, 110 22956100) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP62750
The Whirlpool spacer is an OEM replacement part responsible for maintaining the proper spacing and alignment between the washer cabinet and the top panel. The spacer provides stability and support to the appliance. It ensures that the top panel is securely attached and evenly distributed, preventing any misalignment or instability during operation.
Causes of a bad spacer can include wear and tear over time, physical damage due to accidental impacts, or deformation from prolonged use under stress. These issues can lead to misalignment and operational inefficiencies in the appliance.
Symptoms of a bad spacer include:
- Misalignment of components
- Unusual noises during operation
- Difficulty in assembling or disassembling parts
- Reduced efficiency of the appliance
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Sold individually, four are needed to replace all parts. Screw part number WP3390631.
More
$9.63
- Compare At:
-
$11.46
- You Save:
-
$1.83
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8519200
Structural bracket that secures the rear panel to the washer chassis. Replace if cracked, broken, or missing to restore proper alignment and cabinet stability.
Do-It-Yourself Stories from Customers like You
No spin/agitate. Daniel S. • Landenberg , PA • November 11, 2022
In the end, with a new coupler. But I relearned old lessons the hard way.
The washer is in a rental unit and the tenant complained of no spin. My first intuition was that the coupler failed again because I bought a cheaper one elsewhere a couple of years ago and not the brand name available here at AppliancePartsPros. But we’ll come back to that. Lesson #1: Verify the symptoms firsthand. I dug in right away, popped out the motor and the coupler appeared okay. When I spun it by hand, it turned...
Read more
More
$18.23
- Compare At:
-
$21.69
- You Save:
-
$3.46
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3359452
This locking nut is used for many purposes on a range of machines including household appliances. This nut is often used for leg leveling for machines. It will help with vibrations from washers and dryers. If the nut is used for this purpose and goes missing or becomes damaged, it could cause the machine to vibrate more and seem louder.Nuts are made from metal and are built to last a long time. However, there can still be issues that arise. In some cases, the nuts might go missing if they become loose and the machine is moved. They could also corrode over time and need to be replaced. The replacement of the nut is typically a fast and simple repair.The nut is a genuine OEM replacement part sourced from the manufacturer. It can work with washers, dryers, and combo machines, and is compatible with models from Whirlpool, Kenmore, Maytag, and Roper. The part is sold individually. Owners may want to have several on hand.
Do-It-Yourself Stories from Customers like You
Whirlpool washer was shaking and moving in spin cycle Charles B. • Sioux Falls , SD • September 25, 2018
Replaced 2 springs and brackets. Also replace rear legs and front legs and re leveled. Works fine.
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3390631
10 - 16 x 1/2
Do-It-Yourself Stories from Customers like You
Agitator wasnt sloshing Paige B. • Clarksville , TN • January 30, 2015
I looked inside and saw the teeth were worn off the "dogs" so I purchased the Cam Agitator repair kit and a new bolt. Getting the old bolt out was the hardest part since it was worn and rusted. I ended up having to buy a set of socket extensions and a set of stripped bolt sockets so $45 in tools and it took me an hour to get the old bolt out but putting everything back together was a breeze. I was very proud of myself, as a woman, that I fixed this problem myself and didnt have to pay a repair...
Read more
More
$7.48
- Compare At:
-
$8.90
- You Save:
-
$1.42
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8054980
This lid switch is the washer's safety interlock. It detects when the lid is closed so the machine can agitate and spin, and cuts power when the lid is opened to stop operation and enhance user safety.
- Monitors lid position and allows agitation/spin only when the lid is closed
- Interrupts motor operation if the lid opens during a cycle
- Common failure symptoms: washer won't start or spin, fills but stalls, stops intermittently, or displays "lid open" alerts
- Restores proper cycle progression and safety shutoff when replaced
What's included: One lid switch Install notes:
- Disconnect power and water supply before servicing
- Access the switch from under the top panel/console per your model's procedure
- Release the old switch, move the harness to the new switch, and secure wiring away from moving parts
- Ensure the lid closes and actuates the switch before reassembly and test run
Do-It-Yourself Stories from Customers like You
Direct drive motor coupling failed wouldn't agitate or spin Tim H. • Fort Collins , CO • October 18, 2014
Was set to pull the trigger on a new washer since this one was 10+ years old. Broke a $25 lid switch fumbling to get the washer open before I found the appliancepros video library. Once I got things apart the right way I was able to diagnose the problem in 5 minutes. Identified the $10 part needed. Got the $10 coupling and the $25 switch and had the washer working like new in 20 minutes. I'm pretty proud of myself.. not going to tell anyone about the $25 switch.
Read more
More
$115.49
- Compare At:
-
$137.43
- You Save:
-
$21.94
Genuine Whirlpool part
By: Whirlpool
Part Number: WP62658
Washer thrust ring acts as a bearing spacer between the outer tub and basket drive, controlling end-play and reducing friction. Replace when worn to restore smooth, quiet operation and prevent premature wear.
Do-It-Yourself Stories from Customers like You
Washer driver block was worn out Melissa J. • Battle Creek , MI • March 15, 2015
Purchased parts from your site and did a self repair. Excellent quality , speedy delivery and easy to install. Now our 13 year old washer works as good as new.
Read more
More
$8.95
- Compare At:
-
$10.65
- You Save:
-
$1.70
Genuine Whirlpool part
By: Whirlpool
Part Number: WP62691
Rubber grommet for motor mount stud.
Do-It-Yourself Stories from Customers like You
Washer did not agitate Gary S. • Kimberling City , MO • December 26, 2016
Replaced dog ears.
Read more
More
$8.95
- Compare At:
-
$10.65
- You Save:
-
$1.70
Genuine Whirlpool part
By: Whirlpool
Part Number: W10389328
Inner tub basket holds clothing during wash cycles. Replace if cracked, rusty, or broken. Installs in center of washer between outer tub and agitator.
Do-It-Yourself Stories from Customers like You
Replacement of rusty inner basket Michael K. • Paramus , NJ • April 18, 2015
Ordered the parts from AppliancePartsPros - super fast shipping, and even though I opted for regular shipping all of my parts arrived the very next day, including the big and bulky inner basket. Disassembly went smoothly, simply following the directions in the AppliancePartsPros video. The only problem I had was that the inner basket simply would NOT come of the drive block no matter what I did. Struggled for a few hours trying to take it off. Then, I called AppliancePartsPros and they said it...
Read more
More
$297.64
- Compare At:
-
$337.09
- You Save:
-
$39.45
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8578209
Fixes poor cleaning or clothes not moving during wash cycle. This agitator restores proper wash action by rotating and lifting laundry through water. DIY-friendly repair.
Do-It-Yourself Stories from Customers like You
Agitator was broke Daniel P. • Madison , OH • August 09, 2016
Striped the agitator out and replaced the bottom portion of agitator.
What was amazing was I placed the order Friday at 5 pm. It arrived Saturday at7:30pm.
Read more
More
$103.33
- Compare At:
-
$124.00
- You Save:
-
$20.67
Genuine Whirlpool part
By: Whirlpool
Part Number: W10820044
Replacement power cord that connects your washer to the wall outlet. Includes strain relief for cable protection. Needed when original cord is damaged, pinched, shorted, or worn. Direct plug-in installation.
Do-It-Yourself Stories from Customers like You
Power cord got pinched and shorted out Gary D. • Kentwood , MI • July 27, 2014
Bought a new cord and removed the back of the washer and unclipped the old and clipped in the new. 5 minutes tops.
Read more
More
$80.95
- Compare At:
-
$97.14
- You Save:
-
$16.19
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10086010
Secures the motor to its mounting point in your laundry center. Replace if the retainer is worn, broken, or has lost tension to prevent motor misalignment.
Do-It-Yourself Stories from Customers like You
Motor drive & mounts Mark H. • Winnemucca , NV • October 10, 2024
A former repair man deleted the grommets from the motor mount plate, the spring fastening the motor to the bracket broke the screw inside the motor and once the motor fell out of place the drive to the the transmission was broken.
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: 285353
This retainer ring is a genuine OEM replacement part sourced directly from the manufacturer for use on front load washing machines to hold the boot seal in place. The boot seal is the gasket that seals the washing machine when the door is closed to prevent water from leaking. The retainer ring is located flush against the boot seal and has either a spring clamp or screw clamp that secures it. Over time, this ring may become damaged due to the washing machine's normal use and age. If the ring is not tight, the washing machine could leak when in use. If water is coming from the door, it is a good idea to inspect and replace the retainer ring and possibly the boot as well.Unplug the washing machine to prevent electrocution. Remove the front panel, the detergent dispenser, and the kickplate to access the retainer ring. Locate the clamp on the ring and loosen it. Remove the retainer ring and set it to the side. Inspect the boot and then install the new retainer ring. Tighten the clamp and reassemble the washing machine. This retainer ring is sold as an individual unit. It is designed specifically for washing machines manufactured by Whirlpool.
Do-It-Yourself Stories from Customers like You
Washer would agitate but would not go into high spin sounded like spin was working though Mario M. • Corona , CA • January 03, 2015
Im not a repairman, so all my knowledge to fix my washer came from either youtube or online chats. I posted this to help the next dad trying to save a few bucks.
Door sensor...
Since door sensor worked correctly, verified that by starting washer with door open, and agitate cycle would not start until door was closed. Meaning door sensor worked correctly.
Timer...
In high spin cycle washer sounded correcltly spinning, but when opening door, drum was was not moving. So timer was triggering...
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3400516
Secures panels or brackets in your laundry center to prevent vibration noise. Replace missing, stripped, or worn screws to restore a tight fit.
Do-It-Yourself Stories from Customers like You
Gearbox replacement Dennis M. • Comer , GA • October 21, 2018
Followed online video. It was easy
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3349365
Fix washer leaks with this fill hose connecting the mixing valve to sensor housing. Common repair for water leaking during fill cycle.
Do-It-Yourself Stories from Customers like You
Washer bounced during the spin cycle Thom J. • Sedona , AZ • November 02, 2018
Replaced the suspension springs. How to video made the repair quick and easy.
Read more
More
$13.47
- Compare At:
-
$15.89
- You Save:
-
$2.42
Genuine Whirlpool part
By: Whirlpool
Part Number: WP357213
Push-in.
Do-It-Yourself Stories from Customers like You
Agitator wasnt sloshing Paige B. • Clarksville , TN • January 30, 2015
I looked inside and saw the teeth were worn off the "dogs" so I purchased the Cam Agitator repair kit and a new bolt. Getting the old bolt out was the hardest part since it was worn and rusted. I ended up having to buy a set of socket extensions and a set of stripped bolt sockets so $45 in tools and it took me an hour to get the old bolt out but putting everything back together was a breeze. I was very proud of myself, as a woman, that I fixed this problem myself and didnt have to pay a repair...
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8546455
Supports the spin basket on the center post for smooth, quiet rotation. Replace if your washer is noisy, vibrating excessively, or has poor spin performance.
More
$18.26
- Compare At:
-
$21.55
- You Save:
-
$3.29