Kenmore Washer 110.28062800 (11028062800, 110 28062800) Parts

Once you tilt the washer and prop it against something it's a pretty straight forward and easy fix. If you watch the instructional "How-to" video beforehand, the repair should take between 30 to 60 minutes. It all depends on your skill level and if everything goes smoothly. Make sure you have all the proper tools, grease and blue thread lock at the ready to help you move this repair along faster. This repair was in conjunction with replacing the motor position sensor. I didn't know I needed a... Read more

I read the FAQ section of Appliance Pros parts web site. I found out I needed to replace the temperature control switch, WPW10248240, to correct my problem. This switch also controls the tub filling water level based on air pressure via the attached vinyl tubing. I ordered the switch and the tubing, WP353255, in case mine was no longer any good, and I also ordered the retaining clips for the control cabinet, (2) of WP8312709, because they can be damaged when accessing the controls. My new... Read more

I just replaced the glass lid and broken plastic frame with the all metal one. Call 877 477 7278 for appliancepartspros and order the following Whirlpool parts (prices as of November 2016): 1 lid part number WP8572026 (AP6013408) for $119.81 2 hinges WP8563964 (AP6004844) for $6.17 each 4 screws WPW10119828 (AP6015313) for $1.97 each Total $140.03 plus $8.95 shipping, grand total $148.98 Note that it does not say that this lid will fit model 7800, but the lid will fit this model. The... Read more

Replaced the drain pump and the drain hose (since I was replacing the drain pump). The new drain pump seems to pump out the water more forcefully than the one replaced. Have not received a LD code during the wash cycle since the replacement was installed. Read more

I replaced the water inlet valve assembly. We have relatively hard water and I assumed that over the years those inlet valves were clogged with calcium deposits which in turn led to the high pitched squealing as water was added to the machine. The hardest part of the entire job was releasing the top of the washer to disconnect the hoses from the valve assembly. Everything else was relatively easy. We simply followed the online video. My washer no longer screams and I'm thrilled! Your... Read more

APPLIANCE PARTS PROS HELPED ME AND GUIDED ME FOR THE PARTS. PROBLEM FIXED. Read more

I put all pieces that I ordered on the dryer and plugged it in. Read more

Replaced flow meter and control valve Read more

I ordered two replacement baffles and screws, then lifted the top of the dryer to access the drum and installed the two new baffles. Read more

After shopping for a new Whirlpool Thin Twin Stack, Found appliance parts pros online and decided to take it apart to see if repair was a possibility. APPro's online instructions were easy to follow, in a couple hours it was apart, and I placed the order. Reg ground took a week from NY, so the laundry piled up that week. The parts arrived on Monday morrning, by afternoon the machine was running like new! The cause was the belt tensioner pulley had frozen. Replaced it, drum wheels,snap... Read more

Replaced rotor and stator Read more

Replaced water nozzle plus fabric softener tray assembly. Read more

Ordered the shaft, bearing, seal kit. I didn’t order the tool to press the bearings in. If you’re not experienced in changing bearings, I suggest you order it. Straight forward repair. The top of my Whirlpool Cabrio comes off differently than the video showed, everything else was spot on. The adhesive is tacky...wear surgical gloves, trust me. One more thing, get a 1-1/4 “ short box wrench for taking off the shaft bit. Read more

I listen very carefully and looked up on line many items that may cause it. One thing, along with the knock was a ting like noise. Like tapping on the sheet metal of the machine. I rocked the drum back and forth and could only find a similar nose. Rotating had nothing. At that point I figured it had to do something with the suspension rods. The rod toward the back right side would ever so slightly stick (ball) when rocking the tub then the ball would have a chatter like movement. I lubed up... Read more

I ordered the parts and replaced all of them. Read more

This trash compactor is in our vacation home. We never use it and now we are selling the house. When I looked to replace it I was amazed at how expensive a new compactor would cost. I found the serial number on the current compact entered it and your web site came up. Your schematics were excellent and made the repair very easy! Read more