Kenmore Washer 110.28522701 (11028522701, 110 28522701) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3400516
Secures panels or brackets in your laundry center to prevent vibration noise. Replace missing, stripped, or worn screws to restore a tight fit.
Do-It-Yourself Stories from Customers like You
Gearbox replacement Dennis M. • Comer , GA • October 21, 2018
Followed online video. It was easy
Read more
More
$5.95
- Compare At:
-
$7.14
- You Save:
-
$1.19
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3360824
Fix a slipping or freely spinning top agitator with this upper auger. Restores the ratcheting motion that pulls clothes down. Quick 3-minute repair.
Do-It-Yourself Stories from Customers like You
Top agitator would not spin Daniel C. • Woodbine , MD • January 14, 2017
I have a 25 year old Kenmore washer that works well and didn't want to get a new washer as they don't make them like they used to. Upon removing the top cap of the agitator and doing an inspection, the agitator dogs were completely broken into pieces. Due to age we decided to replace the lower and upper agitator along with the agitator auger dogs repair kit. All new parts and works fine. On inspection of old parts, we probably could have gotten away with just a $5 repair for the plastic...
Read more
More
$92.25
- Compare At:
-
$108.85
- You Save:
-
$16.60
Genuine Whirlpool part
By: Whirlpool
Part Number: WP389387
Agitator won't move or slips during wash? A worn drive shaft causes weak agitation. This shaft transfers motion from the gearcase to restore firm engagement.
Do-It-Yourself Stories from Customers like You
Agitator was not turning Edward M. • Glen Allen , VA • March 10, 2019
I had to replace the drive shaft and the lower agitator. The motor coupling was also worn out. The repair was challenging because I had to rebuild the gear box. This step was really messy and I had to wait for the liquid gasket to set prior to completing the repair. Cleaning and prep of all of the parts tripled the repair time.
Read more
More
$124.70
- Compare At:
-
$148.39
- You Save:
-
$23.69
Genuine Whirlpool part
By: Whirlpool
Part Number: WP616099
This hose clamp secures a hose connection to prevent leaks and keep your appliance running smoothly. It provides a tight, reliable hold on the hose fitting so water or air stays contained during operation.
- Tightens around a hose and fitting to maintain a secure seal
- Helps stop drips, seepage, or loose connections
- Common fix when you see moisture around a hose joint
- Useful if a clamp is rusted, stretched, or no longer holding tension
What's included: One hose clamp. Install notes:
- Unplug power and shut off water (if applicable) before servicing
- Note clamp position/orientation before removal
- Use appropriate screwdriver or nut driver to tighten evenly
- Do not overtighten—ensure a snug, leak-free seal without damaging the hose
Do-It-Yourself Stories from Customers like You
Water leak Steven K. • New City , NY • August 10, 2018
Took off cover, installed new parts.
Read more
More
$9.95
- Compare At:
-
$11.59
- You Save:
-
$1.64
Genuine Whirlpool part
By: Whirlpool
Part Number: 285727
Fix a washer that won't agitate or has stripped agitator teeth. This central wash-motion component mounts to the drive hub. DIY-friendly repair.
Do-It-Yourself Stories from Customers like You
Stripped agitator neck from overloading machine John P. • Fort Myers , FL • April 30, 2016
Replaced agitator.
Read more
More
$159.54
- Compare At:
-
$188.26
- You Save:
-
$28.72
Genuine Whirlpool part
By: Whirlpool
Part Number: W11033823
Secures the door boot gasket to the front tub on front-load washers. Replace if the seal is loose or leaking during wash cycles. Confirm fit with model.
More
$8.95
- Compare At:
-
$10.65
- You Save:
-
$1.70
Genuine Whirlpool part
By: Whirlpool
Part Number: WP389386
This is the central wash-action component in select top-load washers. Replacing a worn or damaged agitator restores proper agitation so clothes circulate through water and detergent for consistent cleaning performance. What it does:
- Converts drive motion into the back-and-forth action that moves laundry
- Circulates clothes to improve soil removal and reduce tangling
- Replaces cracked, stripped, or loose agitators that cause weak or no agitation
- Common symptoms include poor cleaning, clothes not moving during wash, or an agitator that wobbles or spins freely by hand
What's included:
Install notes:
- Disconnect power and turn off water supply before servicing
- Remove the fabric softener dispenser and inner cap to access the center bolt
- Remove the bolt, lift off the old agitator, seat the new agitator on the splined shaft, and secure the bolt
- Reinstall the cap/dispenser; reuse original hardware as applicable and check for a secure fit before testing
Do-It-Yourself Stories from Customers like You
Top agitator would not spin Daniel C. • Woodbine , MD • January 14, 2017
I have a 25 year old Kenmore washer that works well and didn't want to get a new washer as they don't make them like they used to. Upon removing the top cap of the agitator and doing an inspection, the agitator dogs were completely broken into pieces. Due to age we decided to replace the lower and upper agitator along with the agitator auger dogs repair kit. All new parts and works fine. On inspection of old parts, we probably could have gotten away with just a $5 repair for the plastic...
Read more
More
$91.24
- Compare At:
-
$107.66
- You Save:
-
$16.42
Genuine Whirlpool part
By: Whirlpool
Part Number: WP62889
Used for lid switch.
Do-It-Yourself Stories from Customers like You
Washer was "dead" with a partially washed load and would not do anything Jimmy M. • Hopewell , VA • September 19, 2014
Researched this kenmore washer on-line and found the problem to be the lid switch. Saw a diagram on how to jump this switch by connecting a wire to both outside wires on the harness and voila! It worked! This is not a fix but it allowed me to finish the load of unwashed clothes and told me which part was bad (do not run washer jumped like this.......fire hazard!)
Ordered the lid switch and it was an easy repair. A $14.00 switch was a lot cheaper than a $450.00 washer. Thanks appliance parts...
Read more
More
$16.77
- Compare At:
-
$19.79
- You Save:
-
$3.02
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8546455
Supports the spin basket on the center post for smooth, quiet rotation. Replace if your washer is noisy, vibrating excessively, or has poor spin performance.
More
$18.26
- Compare At:
-
$21.73
- You Save:
-
$3.47
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3355454
Replace your washer's anti-rattle clip to eliminate vibration noise and buzzing during cycles. Secures components with light spring tension. Confirm fit with your model number before ordering.
Do-It-Yourself Stories from Customers like You
My washer wouldn't go into a spin cycle. Joshua P. • Cohutta , GA • April 18, 2021
I bought a clutch liner kit installed it in 5 minutes now it spins faster than ever.
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP16123
Rubber washer gasket for washer fill hose connections. Replace if worn or leaking at coupler adapter. Measures 1-1/16 x 5/8 inch. Verify fit with model.
Do-It-Yourself Stories from Customers like You
Water inlet valve was corroded and broken washer Sandra H. • Belton , MO • June 26, 2015
Replaced with new part ordered from store
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: W10846509
The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear bulkhead to the tub, ensuring vibrations are reduced through solid mounting points. Properly installed screws dampen oscillating movement.
Causes of a bad screw include damage from water exposure like corrosion or breakage from stress concentrations if the tub bangs around during imbalanced loads.
Symptoms of a bad screw include:
- Loose or detached rear bulkhead allowing side-to-side play
- Excessive noise and shaking felt through the surrounding walls
- Development of micro-cracks around screw holes over time
- Potential leak paths if holes are no longer sealed
This Whirlpool replacement screw restores a stable suspension system. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Whirlpool direct drive washer major repair drive/brake assembly clutch suspension outer tub etc Carter H. • Oak Ridge , TN • July 11, 2015
Watched several repair videos on YouTube produced by AppliancePartsPros.com for this model Whirlpool washer (videos quite well done). Purchased parts from AppliancePartsPros.com; order correctly filled and parts arrived by FedEx within two working days. Performed repairs as instructed. "Plastic welded" holes in poly outer tub using similar plastic (PP) using a cheap soldering iron - worked perfectly, saved >$150 for new tub. Washer now like brand new. Suggestion - buy the spanner wrench,...
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2172937
This three-circuit connector housing organizes and protects terminals in an appliance wiring harness. It provides a secure, insulated plug connection to help prevent loose contacts, heat damage, and intermittent operation when the original housing is cracked or melted. What it does:
- Holds three wiring terminals in the correct orientation for a mating connector
- Insulates and locks terminals to reduce arcing and overheating at the plug
- Replaces cracked, brittle, or heat-damaged connector housings
- Symptoms can include intermittent power, burnt odor near the connector, discoloration/melting, or a plug that won't stay latched
What's included:
- 1 three-circuit connector housing
Install notes:
- Disconnect power before servicing the appliance
- Note wire/terminal positions and transfer them one at a time into the new housing
- Inspect terminals; replace any that are discolored, loose, or damaged. Use the correct crimp tool/terminals specified for your model
- Fully seat each terminal until it locks and the connector latch engages securely
More
$13.48
- Compare At:
-
$16.18
- You Save:
-
$2.70
Genuine Whirlpool part
By: Whirlpool
Part Number: WP273556
Size: 10-16 x 5/8 inch.
Do-It-Yourself Stories from Customers like You
Console screws were rusty and the other screw was broken. Denis C. • Baltimore , MD • June 20, 2018
I used a screwdriver and removed all three screws and replaced them with ones I ordered from you. The job took less than ten minutes to complete.
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP54583
Right hand side. For screws use WPW10119828.
Do-It-Yourself Stories from Customers like You
Whirlpool washer David L. • Linn , MO • August 31, 2015
With the parts supplied from your company. The lady that took my order was good at her job. All the parts were correct and fit. I thank you for the service that recieved.
Read more
More
$19.50
- Compare At:
-
$23.40
- You Save:
-
$3.90
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8546461
Fixes grinding noise or basket won't spin issues by disengaging the brake during spin cycles. Restores smooth operation when cam wears out or breaks.
Do-It-Yourself Stories from Customers like You
No spin every thing else worked made high speed ticking noise Anthony D. • Follansbee , WV • May 12, 2015
First I looked at the many you tube vids, and there are many. appliance parts pros pretty much shows you how to deal with the parts. I changed the brake shoes and the clutch assembly which also comes with the driver cam. I also changed the metal brake operating cam. I think that brake lockup or improper brake release was the problem that broke the plastic cam driver. This was the broken plastic part making all the ticking noise. I first changed the coupling on the motor but that wasn't bad. in...
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13