Kenmore Washer 110.45986403 (11045986403, 110 45986403) Parts

The Drain Hose is an OEM replacement part for Whirlpool washing machines. Replacements are typically needed due to compression fatigue caused by years of absorbing hydraulic pounding. Additionally, mineral buildup within hoses can reduce drainage efficiency over time.

Symptoms involve:

• Remaining water pockets not fully evacuating after rinses
• Premature alerts about blocked pumps requiring inspection
• Damp loading areas traced to splits along pressure-prone locations

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air, and some Kenmore models.

The Water Temperature Sensor is an OEM part for Whirlpool washing machines. This sensor ensures the water is reaching the proper temperature at each stage of the wash cycle. Note: The sensor does not include the seal WP8540766. Order separately if needed. 

Causes of a bad temperature sensor can be failures over time due to mechanical wear, thermal stress on electronic components, or damage from leaks/flooding inside the unit.

Symptoms of a bad water temperature sensor include:

• Inability to switch between wash steps or advance through the cycle
• Erratic or inconsistent temperature readings
• Failure alarms or error codes displayed
• Improper or incomplete washing even on high heat settings

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 

The Water Level Pressure Switch Hose is an OEM replacement part for Whirlpool washing machines. This hose connects to the water level pressure switch, transmitting pressure changes as the tub fills and drains. It ensures the washing machine accurately gauges the water level, preventing overfilling or insufficient water during cycles.

Causes for a malfunctioning Water Level Pressure Switch Hose can include clogs, kinks, or wear and tear over time that affects its ability to transmit pressure changes effectively.

Symptoms of a bad Water Level Pressure Switch Hose include:

• The washing machine overfilling or not filling enough
• Inaccurate water level readings leading to inefficient wash cycles
• Water not draining properly, indicating a pressure transmission issue
• Visible damage or wear to the hose

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This screw is used to secure the handle end cap to the center of the door. The screw size measures 8-18 x 1/2 inches.

The Door Strike is an OEM replacement part for Whirlpool front-loading washing machines. It is the metal component integrated into the washer cabinet that securely receives and holds the washing machine door shut during cycles. 

Causes of a bad door strike can include normal wear over time. Excessive force on the door or damage to strike mechanics may compromise its integrity.

Symptoms of a failed door strike include:

• Gapping at the door seam permitting water leaks and reduced cleaning 
• Inability to fully latch closed for safety-certified operation
• Loose motion, impact damage, or misaligned connecting pieces  
• Recurring errors involving the door lock mechanism

This is the male piece to the door latch assembly on a front load washer. For the door latch assembly order WP8182634.

This OEM Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore front-load washers.

The Hose Clamp is an OEM part for Whirlpool washing machines. This clamp secures the hose in place, ensuring a tight connection and preventing leaks during operation. It is essential for maintaining the integrity of the washing machine's water system, securing hoses that carry water to and from the washer.

Common causes of a bad hose clamp include rust, physical damage, or loosening from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Water leaks around the hose connection points
• The hose slipping off the fitting
• Visible rust or wear on the clamp
• Difficulty in tightening the clamp to secure the hose

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

The Drive Pulley is an OEM replacement part specific to Whirlpool washing machines. It is a toothed wheel component located inside the washer cabinet that functions with the belt to rotate the wash drum. The drive pulley provides the rotational force needed to agitate clothes and turbulent water during cycle operation.

Causes of a faulty drive pulley include normal wear of the plastic material from extended years of operation.

Symptoms include:

• Abnormal noises (squealing or screeching sounds) emanating from within the washer cabinet
• Slow or weak drum motion, even on high agitation settings
• Premature belt wear due to slipping of the drive pulley teeth
• Visible cracks or splitting in the pulley surface

This genuine OEM part is also compatible with select Maytag, KitchenAid, and other washer brands.

The Detergent Drawer is an OEM part for Whirlpool washing machines. It is responsible for holding and dispensing detergent and fabric softener during the wash cycle. The drawer ensures that the right amount of detergent is released at the appropriate time for optimal cleaning performance.

Causes of a bad detergent drawer can include clogging or residue buildup, damage to the drawer or its tracks, or malfunctioning mechanisms that prevent the proper dispensing of detergent. Over time, these issues can lead to inefficient cleaning and potential damage to your washing machine.

Symptoms of a bad detergent drawer include:

• Detergent not dispensing properly
• Residue left in the drawer after the cycle
• Difficulty sliding the drawer in or out
• Leaks or spills from the drawer area

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This motor control board is created for use with washing machines. It's located inside the washing machine, where users can change settings and start or stop the appliance. It is tasked with regulating how quickly the washer spins during a cycle. Wear and tear or damage can cause the motor control board to malfunction. This may make it impossible for the washer to agitate or spin. If this happens, a replacement will need to be made.To replace this part, start by unplugging the appliance. Once the area is safe, the bottom front panel should be removed. This will provide access to the original motor control board. Pull on the motor control board until the wires can be reached. The position of these components should be noted before taking out the part. Replace with a new motor control board and replace the wires.This motor control board is designed to fit washing machines made by Maytag, Whirlpool, Kenmore, and KitchenAid. This is an authentic OEM replacement part that is sourced directly from the manufacturer. It's sold as a single part.

This replacement seal restores a watertight connection in your washer to help prevent leaks and moisture damage. It replaces a worn, cracked, or flattened original seal so components stay tightly sealed during use.

• Creates a compression barrier between mating parts to contain wash water
• Helps stop drips and seepage during fill, wash, or drain
• Can address water leaks, moisture under the unit, or musty odors from trapped water
• Replaces seals that are brittle, torn, or misshapen

• Disconnect power and turn off water supply before servicing
• Access the seal location per your model's service information and note orientation
• Clean grooves and mating surfaces; seat the new seal evenly (a light film of water or mild soap can aid installation)
• Reassemble and run a short cycle to check for leaks

The Screw is an OEM part for Whirlpool appliances. This specific screw is used in various locations within Whirlpool appliances, securing components and ensuring the stability and proper alignment of parts. It is designed to fit precisely and maintain a firm hold, contributing to the overall functionality and safety of the appliance.

Over time, screws can become worn or stripped due to regular use, corrosion, or over-tightening. 

Causes of a bad screw include wear and tear, exposure to moisture leading to rust, and over-tightening which can strip the threads.

Symptoms of a bad screw include:

• Loose or wobbly components
• Misalignment of parts
• Noise due to vibrating or loose parts
• Difficulty in securing or removing the screw

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Size: 5 foot long. Rubber fill hose used on most automatic washing machines. Two hoses used per machine.

This outer drain hose routes wastewater from your washer to the household standpipe or sink. Replacing a cracked, kinked, or clogged hose restores proper draining and helps reduce leaks at the back of the appliance.

• Carries discharge water from the drain pump outlet to the home drain connection
• Damage such as splits, pinholes, or hardening can cause leaks during the drain cycle
• Kinks or blockages can lead to slow or no draining and water left in the tub
• Visible wear, brittleness, or recurring drain errors are common signs the hose needs replacement

• Disconnect power and turn off water supply before servicing
• Pull the washer forward to access; keep towels or a pan ready for residual water
• Detach the old hose from the pump/outlet and household drain; transfer and reuse clamps or brackets as required by your model
• Route the new hose without kinks, secure all connections, follow your model's manual for drain placement, then run a test drain and check for leaks

This replacement hose restores a secure, leak-free water path inside your appliance so it can move water where it's needed to fill, circulate, or drain correctly. Replacing a worn hose helps prevent leaks and related performance issues.

• Directs water between internal components as designed
• Maintains proper flow for filling, circulation, or draining
• Helps seal connections when correctly clamped and routed
• Common symptoms of a failed hose include leaks under the unit, slow or incomplete draining, erratic filling, or water-related error codes

• Disconnect power and shut off the water supply before servicing
• Note routing and orientation; replace one end at a time to match the original path
• Inspect and reuse OEM clamps if in good condition, or replace if corroded or weakened; fully seat all connections
• Run a brief test cycle and check all joints for leaks after installation

This OEM replacement part is a control board for washers. The control board is the main computer that sends signals to the washer to perform its essential functions. If the washer is no longer turning on, spinning, rinsing or draining properly, this could mean that the control board needs to be replaced. Luckily this is a relatively simple repair. To begin, start by shutting off all power to the appliance. Proceed to move the washer away from the wall to gain access to the upper back panel. Remove the upper back panel and locate the old control board. Pull it out of its mounted position and take note of the orientation of the wires attached to the old board. Reinsert the wire harness and individual wire into their correct terminals on the new board. Snap the board back into place and reinstall the upper back panel. This genuine replacement part is sold individually and is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Sears/Kenmore brand washers.

Includes all four shipping bolts.