Kenmore Dryer 110.96093800 (11096093800, 110 96093800) Parts

My dryer lint filter was clogged beyond regular cleaning due to its age. After 15 years of daily use it was time to replace. In.the process of determining why the dryer was taking so long to dry loads, I noticed the filter housing gasket had torn off somehow which allow a lot of lint to pass through into the dryers main housing. I believe this prevented the dryer to have good air flow. Replacing both the filter and its housing was easy and fixed the problem pronto! I saved myself $1000 by... Read more

This was actually one of the easiest fixes I’ve done. All that was required was to remove 3 screws to remove the broken part. I used a pair of pliers to remove the moisture sensors from the broken part to the new one. Read more

First I watched videos about squeaking Kenmore dryers. Then I used that information to open the dryer, diagnosing the fact that the roller on the drum belt tension arm had broken and actually fallen off the arm. The dryer was filled with lint and dust/dirt, so I also saw that the seals on the dryer had deteriorated greatly. AppliancePartsPros website is outstanding, far better than its competitors. This made it easy to find the parts and videos that I needed. It took hours to pull everything... Read more

Replaced the roller, shaft, rings and washer. After removing the back, reverse threading the nut off, discarding the old hardware and installing the new hardware back in business in about 20 minutes. Read more

I had to remove my dryer so I could install a new floor. The dryer would not fit through the doorway with the power cord attached. Since the power cord was fastened to the back using 3 phillip headed screws, I gently backed them out with a phillip headed screwdriver. However, two of the 3 screws gave me extreme trouble. The head of the screws were made of such a weak metal, that the screw head began stripping. I have a phillip screw kit with different sized heads, so I picked a head that... Read more

Removed and replaced start switch then motor, no joy. removed the timer for disassembly, found bad contact. soldered contact to the spring tab and assembled and installed the timer. All good now. Read more

Using You Tube How-To Videos. Replaced the drum drive belt and tensioner pulley/arm (including) the spring. Read more

One day my wife went to bake something and the bake/broil buttons as well as #3, #9, and oven light ceased to work. Local repair guy came by and wanted to charge $500 to fix it....YEAH RIGHT! Did a little homework and found this website, spoke with knowledgable staff who pointed me in the right direction. Took me all of about 20 minutes to install new control panel..everything works perfect...THANKS! p.s. In doing my research come to find Maytag did little to insulate control panel from oven... Read more

And after replacing the thermal fuse The dryer turned on. Read more

• No heat or not enough heat

I ordered the parts through AppliancePartsPros.com. They were delivered the next day. I installed them and the dryer works great. Read more

Watched You tube videos to narrow the problem down to old deteriorated gaskets. Read more

THIE REPAIR WAS ON A WHIRLPOOL TOP LOAD WASHING MACHINE At first I suspected the leak was from the pump because I had replaced the pump 2 times over 10 years. This time with the cabinet removed and filling the tub with water, I saw water running down one of the steel support arms that go under the tub, so I was guessing that it was coming from the tub seal. I had to use a jumper wire to bypass the Lid Switch so the water would drain. Several months before I had this issue with the water leaking... Read more

Well i thought i had to replace the whole metal casing, turns out the element is separate and that was all i would have needed. but i cot my original casing apart only to find out that was a mistake. anyway i got it all repaired now and its working like new. Read more

Order part and removed 3 hex head screws at top front edge of dryer and slightly lifted up on control panel to lift off pane. It has hangers that support panel while servicing. Remove 2 screws at inside top edge of dryer opening (where lever of switch protrudes) disconnect 3 wire clips at old switch and restore wire clips at new switch and place switch into position and restore 2 screws to secure switch body. Read more

After shopping for a new Whirlpool Thin Twin Stack, Found appliance parts pros online and decided to take it apart to see if repair was a possibility. APPro's online instructions were easy to follow, in a couple hours it was apart, and I placed the order. Reg ground took a week from NY, so the laundry piled up that week. The parts arrived on Monday morrning, by afternoon the machine was running like new! The cause was the belt tensioner pulley had frozen. Replaced it, drum wheels,snap... Read more

I went online and typed in my model number. I was just going to order the dryer belt, but decided that changing all the movable parts at the same time would be best - I definitely recommend doing this, since it was the tensioner pulley and not the belt. My husband is handy, which is why this was not a problem. The whole dryer needs to come apart in order to do this repair. At first I thought I received the wrong parts because I have a front load washer and dryer set, but the picture on the... Read more