Kenmore Dryer 110.96573220 (11096573220, 110 96573220) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3395382
The Start Switch is an OEM replacement part for Whirlpool dryers. It is an electronic component responsible for initiating the heating elements and tumble cycles upon user command from the control panel.
Causes of a bad start switch involve general wear over extended use. Failure of the internal conducting surfaces interrupts circuit activation as well.
Symptoms of a bad start switch include:
- Heating elements or tumble cycles that will not engage properly
- Dryer fails to operate or stops mid-cycle unexpectedly
- Control panel appears non-responsive to selections
- Error codes related to ignition or power delivery faults
Note: This dryer push-to-start switch has 2 terminals.
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore electric dryer models.
Do-It-Yourself Stories from Customers like You
Dryer wouln't start heard the timer working but the starter wouldn't start Perry B. • Stockton , CA • December 05, 2014
I replaced the starter switch, that really didn't need to be replaced, and the thermal fuse, which did.
Read more
More
$49.40
- Compare At:
-
$58.29
- You Save:
-
$8.89
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8541818
The heater box houses your dryer's heating element and screen. Replace this component when rusted, corroded, or the screen is damaged causing snags or stains.
Do-It-Yourself Stories from Customers like You
The grill face in the dryer where the heat comes out was worn and had developed edges where clothes were catching and pulling thread Willard W. • Rochester , NY • April 06, 2017
Replaced the heater tube. Had to open the back up, removed the heating element and then replaced the heater tube. Then I put it all together again and everything is fine now.
Read more
More
$126.68
- Compare At:
-
$149.48
- You Save:
-
$22.80
Genuine Whirlpool part
By: Whirlpool
Part Number: WP488729
This screw is used to secure the handle end cap to the center of the door. The screw size measures 8-18 x 1/2 inches.
Do-It-Yourself Stories from Customers like You
The lint catch was broken Misti P. • Spokane , WA • January 18, 2019
This was actually one of the easiest fixes I’ve done. All that was required was to remove 3 screws to remove the broken part. I used a pair of pliers to remove the moisture sensors from the broken part to the new one.
Read more
More
$7.31
- Compare At:
-
$8.70
- You Save:
-
$1.39
Genuine Whirlpool part
By: Whirlpool
Part Number: 279320
The Terminal Block Kit is an OEM part for Whirlpool dryers. This kit includes the terminal block, wires, wire connectors, screws, brackets and instructions.
Common causes of a bad terminal block include overheating due to loose connections, corrosion from moisture exposure, and physical damage from handling or installation errors.
Symptoms of a bad terminal block kit include:
- Dryer not starting or losing power during operation
- Burning smell or visible burn marks near the terminal block
- Loose or frayed wires connected to the terminal block
- Intermittent electrical issues or malfunctioning controls
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Could not remove old power cord from back of dryer (screw heads stripped due to soft metal) Michael A. • Lewiston , ME • August 26, 2017
I had to remove my dryer so I could install a new floor. The dryer would not fit through the doorway with the power cord attached. Since the power cord was fastened to the back using 3 phillip headed screws, I gently backed them out with a phillip headed screwdriver. However, two of the 3 screws gave me extreme trouble. The head of the screws were made of such a weak metal, that the screw head began stripping. I have a phillip screw kit with different sized heads, so I picked a head that...
Read more
More
$43.22
- Compare At:
-
$51.43
- You Save:
-
$8.21
Genuine Whirlpool part
By: Whirlpool
Part Number: WP308685
Screw secures appliance panels and access covers. Replace missing, stripped, or corroded screws to restore tight fit and eliminate rattles or gaps.
Do-It-Yourself Stories from Customers like You
Under the counter mounting brackets were missing Douglas A. • Glen Allen , VA • June 19, 2019
After several attempts at Local Hardware stores and Lowe's and Home Depot to find them I called AppiancePartsPros.com. I gave them the model number and what I was looking for and customer service directed me to the part on the Web site. They were extremely helpful and it was very fast and I got the parts the next day.
Read more
More
$7.31
- Compare At:
-
$8.63
- You Save:
-
$1.32
Genuine Whirlpool part
By: Whirlpool
Part Number: 279393
Dryer won't power on or has loose power cord connection? This terminal block screw kit secures electrical connections. Easy DIY fix in 15 minutes.
Do-It-Yourself Stories from Customers like You
Dryer would not turn on. Keith K. • Melbourne , FL • May 19, 2020
And after replacing the thermal fuse The dryer turned on.
Read more
More
$29.95
- Compare At:
-
$35.64
- You Save:
-
$5.69
Genuine Whirlpool part
By: Whirlpool
Part Number: WP90767
The Whirlpool screw is an OEM replacement part responsible for securing various components or parts on different types of Whirlpool appliances. The screw is designed to provide a secure and reliable fastening connection, ensuring that different parts of the appliance stay in place. It is commonly used in different locations within the appliance, such as the cabinet, panels, or other structural elements.
This part fixes the following symptoms:
- Loose or wobbly components within the appliance
- Panels or parts that are not securely attached
- Rattling or unusual noises due to loose parts
- Damaged or missing screw
The Whirlpool screw can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
Do-It-Yourself Stories from Customers like You
Certain buttons were'not working Brent T. • Easton , MD • November 17, 2014
One day my wife went to bake something and the bake/broil buttons as well as #3, #9, and oven light ceased to work. Local repair guy came by and wanted to charge $500 to fix it....YEAH RIGHT! Did a little homework and found this website, spoke with knowledgable staff who pointed me in the right direction. Took me all of about 20 minutes to install new control panel..everything works perfect...THANKS!
p.s. In doing my research come to find Maytag did little to insulate control panel from oven...
Read more
More
$7.31
- Compare At:
-
$8.70
- You Save:
-
$1.39
Genuine Whirlpool part
By: Whirlpool
Part Number: 279318
Includes screws and wire connectors. For the complete terminal block kit use 279320.
This part fixes the following symptoms
-
No heat or not enough heat
See more...
Do-It-Yourself Stories from Customers like You
Loose wire in back caused a short and burned out plug insulator etc William W. • Pottsboro , TX • February 15, 2019
I ordered the parts through AppliancePartsPros.com. They were delivered the next day. I installed them and the dryer works great.
Read more
More
$56.95
- Compare At:
-
$67.20
- You Save:
-
$10.25
Genuine Whirlpool part
By: Whirlpool
Part Number: WP98234
U-type clip nut slides onto sheet metal panels to create threaded anchor points for screws. Replace if broken, missing, or worn during repairs.
Do-It-Yourself Stories from Customers like You
Broken dryer belt and not heating as good as it used to. Jimmie F. • Winfield , KS • January 15, 2018
I undid the top with a putty knife, took out two screws and took off the front. I replaced the drum rollers and put the new belt on the drum, looped the belt on the idler and then onto the motor pulley. I also put on two new top hold down clips as the old ones broke because they were plastic, the new ones were metal. I took off the back panel and replaced the heating element. The hardest part was cleaning up all of the lint and dirt that had accumulated over the years. It was not difficult,...
Read more
More
$11.51
- Compare At:
-
$13.58
- You Save:
-
$2.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP388326
This console screw secures the control console to the appliance cabinet or top, keeping the panel tight and aligned. Replace a missing or damaged screw to stop panel wobble and rattling and maintain a snug, stable fit. What it does:
- Fastens the control console/control panel to the cabinet or top panel
- Helps maintain alignment and reduces vibration and rattling
- Replaces a missing, stripped, or rusty original screw
- Common fix for a loose or lifting console/panel
What's included:
Install notes:
- Disconnect power before service; if applicable, shut off gas/water
- Support the console to avoid straining wiring harnesses
- Start threads by hand to prevent cross-threading; tighten until snug—do not overtighten
- Use the correct driver style for your model's hardware
Do-It-Yourself Stories from Customers like You
Leaking water from the tub seal David C. • Bessemer City , NC • January 27, 2018
THIE REPAIR WAS ON A WHIRLPOOL TOP LOAD WASHING MACHINE
At first I suspected the leak was from the pump because I had replaced the pump 2 times over 10 years. This time with the cabinet removed and filling the tub with water, I saw water running down one of the steel support arms that go under the tub, so I was guessing that it was coming from the tub seal. I had to use a jumper wire to bypass the Lid Switch so the water would drain.
Several months before I had this issue with the water leaking...
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP348197
This support washer is a flat spacer used within the mechanism to support and separate mating parts, maintaining alignment and smoother movement. Replacing a worn washer helps reduce friction and wear so components operate properly. What it does:
- Maintains proper spacing and support between adjoining parts
- Helps prevent metal-to-metal contact, reducing scraping or grinding noises
- Addresses wobble or excess play when the original washer is worn, deformed, or missing
- Restores smoother movement and alignment in the assembly
What's included:
Install notes:
- Disconnect power and water supply before servicing; for gas combos, also shut off gas
- Refer to your model's parts diagram for location and orientation
- Track the order of any shims/spacers during disassembly and reinstall in the same sequence
- Tighten fasteners to manufacturer guidance to avoid deforming the washer or binding parts
Do-It-Yourself Stories from Customers like You
Screaching noise Linda Z. • Kailua Kona , HI • February 06, 2015
Followed the video- opened the front of the dryer and removed the drum. It was evident that one of the wheels had worn and wasn't turning freely like the other one. The video showed how to remove the roller. Very simple process and now the dryer works just fine.
Read more
More
$5.95
- Compare At:
-
$7.14
- You Save:
-
$1.19
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8066056
The Door Hinge is an OEM part for Whirlpool dryers. This hinge ensures the secure attachment of the dryer door to the appliance, allowing it to open and close smoothly. Right-hand hinge. For the left hinge use AP3047600
Causes of a bad door hinge can include regular wear and tear, accidental impacts, or overloading the door.
Symptoms of a bad door hinge include:
- Door not closing properly
- Door sagging or misaligned
- Difficulty opening or closing the door
- Noises or squeaking when moving the door
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Broken dry door hinge. Lynda S. • Apex , NC • September 24, 2018
Watched your very helpful and informative "how to" video and replaced both right and left hinges. Getting the front panel to line up on the clips was the most difficult part.
Read more
More
$52.95
- Compare At:
-
$63.54
- You Save:
-
$10.59
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3359452
This locking nut is used for many purposes on a range of machines including household appliances. This nut is often used for leg leveling for machines. It will help with vibrations from washers and dryers. If the nut is used for this purpose and goes missing or becomes damaged, it could cause the machine to vibrate more and seem louder.Nuts are made from metal and are built to last a long time. However, there can still be issues that arise. In some cases, the nuts might go missing if they become loose and the machine is moved. They could also corrode over time and need to be replaced. The replacement of the nut is typically a fast and simple repair.The nut is a genuine OEM replacement part sourced from the manufacturer. It can work with washers, dryers, and combo machines, and is compatible with models from Whirlpool, Kenmore, Maytag, and Roper. The part is sold individually. Owners may want to have several on hand.
Do-It-Yourself Stories from Customers like You
Whirlpool washer was shaking and moving in spin cycle Charles B. • Sioux Falls , SD • September 25, 2018
Replaced 2 springs and brackets. Also replace rear legs and front legs and re leveled. Works fine.
Read more
More
$5.95
- Compare At:
-
$7.14
- You Save:
-
$1.19
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10109200
This replacement screw secures panels, brackets, and other components in your appliance to keep them aligned and rattle-free. Replacing worn, stripped, or missing hardware restores a tight fit and helps maintain safe, quiet operation.
- Fastens panels, brackets, or internal parts to the cabinet/frame
- Helps maintain alignment to reduce vibration and rattling
- Replaces lost, stripped, or corroded screws
- Common symptoms: loose panels/trim, rattles, or a screw that won't tighten
What's included: One screw. Install notes:
- Disconnect power; shut off water or gas if applicable
- Match thread and length to the original; replace one at a time to keep alignment
- Start threads by hand to avoid cross-threading; use the correct driver
- Tighten snugly—do not overtighten, especially into plastic or thin sheet metal
Do-It-Yourself Stories from Customers like You
Missing baffles Anna S. • Shoreview , MN • January 31, 2016
I ordered two replacement baffles and screws, then lifted the top of the dryer to access the drum and installed the two new baffles.
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3393657
Dryer belt slipping off motor pulley or making squealing noises? The belt restrainer keeps the drive belt aligned. Moderate DIY repair with video guide.
Do-It-Yourself Stories from Customers like You
Loud squealing noise when dryer (Whirlpool) is turned on Marc P. • Chesterfield , MI • December 31, 2018
Using You Tube How-To Videos.
Replaced the drum drive belt and tensioner pulley/arm (including) the spring.
Read more
More
$73.40
- Compare At:
-
$87.35
- You Save:
-
$13.95
Genuine Whirlpool part
By: Whirlpool
Part Number: WP681414
Specs: 10-16 x 1/2 inch.
Do-It-Yourself Stories from Customers like You
Dryer drum was beginning to stall occasionally Dana J E. • San Marcos , CA • March 17, 2015
After shopping for a new Whirlpool Thin Twin Stack, Found appliance parts pros online and decided to take it apart to see if repair was a possibility. APPro's online instructions were easy to follow, in a couple hours it was apart, and I placed the order. Reg ground took a week from NY, so the laundry piled up that week. The parts arrived on Monday morrning, by afternoon the machine was running like new! The cause was the belt tensioner pulley had frozen. Replaced it, drum wheels,snap...
Read more
More
$5.95
- Compare At:
-
$7.14
- You Save:
-
$1.19